• Structural Monitoring and Maintenance
• /
• v.10 no.3
• /
• pp.207-220
• /
• 2023

The safety of bridges are critical in our transportation infrastructure. Bridge design and analysis require complex structural analysis procedures to ensure their safety and stability. One common method is to calculate the maximum moment in the girders to determine the appropriate bridge section. Girder distribution factors (GDFs) provide a simpler approach for performing this analysis. A GDF is a ratio between the response of a single girder and the total response of all girders in the bridge. This paper explores the significance of GDFs in bridge analysis and design, including their importance in the evaluation of existing bridges. We utilized Bridge Weigh-in-motion (B-WIM) measurements of five simple supported girder bridge in Indonesia to develop a simple GDF provisions for the Indonesia's bridge design code. The B-WIM measurements enable us to know each girder strain as a response due to vehicle loading as the vehicle passes the bridge. The calculated GDF obtained from the B-WIM measurements were compared with the code-specified GDF and the American Association of State Highway and Transportation Officials (AASHTO) Load and Resistance Factor Design (LRFD) bridge design specification. Our study found that the code specified GDF was adequate or conservative compared to the GDF obtained from the B-WIM measurements. The proposed GDF equation correlates well with the AASHTO LRFD bridge design specification. Developing appropriate provisions for GDFs in Indonesian bridge design codes can provides a practical solution for designing girder bridges in Indonesia, ensuring safety while allowing for easier calculations and assessments based on B-WIM measurements.

• Advances in aircraft and spacecraft science
• /
• v.10 no.6
• /
• pp.495-519
• /
• 2023

The drone serves the customers not served by vans. At the same time, considering the safety, policy and terrain as well as the need to replace the battery, the drone needs to be transported by truck to the identified station along with the parcel. From each such station, the drone serves a subset of customers according to a direct assignment pattern, i.e., every time the drone is launched, it serves one demand node and returns to the station to collect another parcel. Similarly, the truck is used to transport the drone and cargo between stations. This is somewhat different from the research of other scholars. In terms of the joint distribution of the drone and road vehicle, most scholars will choose the combination of two transportation tools, while we use three. The drone and vans are responsible for distribution services, and the trucks are responsible for transporting the goods and drone to the station. The goal is to optimize the total delivery cost which includes the transportation costs for the vans and the delivery cost for the drone. A fixed cost is also considered for each drone parking site corresponding to the cost of positioning the drone and using the drone station. A discrete optimization model is presented for the problem in addition to a two-phase heuristic algorithm. The results of a series of computational tests performed to assess the applicability of the model and the efficiency of the heuristic are reported. The results obtained show that nearly 10% of the cost can be saved by combining the traditional delivery mode with the use of a drone and drone stations.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.4
• /
• pp.1108-1119
• /
• 2018

As the interest on the air pollution is gradually rising at home and abroad, automotive and fuel researchers have been studied on the exhaust and greenhouse gas emission reduction from vehicles through a lot of approaches, which consist of new engine design, innovative after-treatment systems, using clean (eco-friendly alternative) fuels and fuel quality improvement. This research has brought forward two main issues : exhaust emissions (regulated and non-regulated emissions, PM particle matter) and greenhouse gases of vehicle. Exhaust emissions and greenhouse gases of automotive had many problem such as the cause of ambient pollution, health effects. In order to reduce these emissions, many countries are regulating new exhaust gas test modes. Worldwide harmonized light-duty vehicle test procedure (WLTP) for emission certification has been developed in WP.29 forum in UNECE since 2007. This test procedure was applied to domestic light duty diesel vehicles at the same time as Europe. The air pollutant emissions from light-duty vehicles are regulated by the weight per distance, which the driving cycles can affect the results. Exhaust emissions of vehicle varies substantially based on climate conditions, and driving habits. Extreme outside temperatures tend to increasing the emissions, because more fuel must be used to heat or cool the cabin. Also, high driving speeds increases the emissions because of the energy required to overcome increased drag. Compared with gradual vehicle acceleration, rapid vehicle acceleration increases the emissions. Additional devices (air-conditioner and heater) and road inclines also increases the emissions. In this study, three light-duty vehicles were tested with WLTP, NEDC, and FTP-75, which are used to regulate the emissions of light-duty vehicles, and how much emissions can be affected by different driving cycles. The emissions gas have not shown statistically meaningful difference. The maximum emission gas have been found in low speed phase of WLTP which is mainly caused by cooled engine conditions. The amount of emission gas in cooled engine condition is much different as test vehicles. It means different technical solution requires in this aspect to cope with WLTP driving cycle.

• Journal of Korean Society of Transportation
• /
• v.35 no.6
• /
• pp.499-510
• /
• 2017

Traffic accident fatalities in Korea in 2016 was 4,292 and 1,732 cases were deaths of elderly people. In spite of this, the researches on behaviors of the elderly when crossing roads, are rather limited. The purpose of this study is to investigate and analyze road crossing behavior characteristics of the elderly, when crossing roads, especially focusing on the characteristics of pedestrians and vehicles. Cross-sectional data was collected from six different sites in two regions and the following results was identified. First, at road crossings, 528 cases(84.3%) out of 626 conflict situations of the elderly and 303 cases(63.3%) out of 478 conflict situations of the non-elderly pedestrians were found to be dangerous, respectively. The elderly tend to face a statistically significant risk of 3.11 times higher than that of non-elderly people. Second, 519 cases(82.9%) of jaywalking occurred in 626 conflict cases of the elderly and 375 cases(78.5%) of jaywalking in 478 conflict events of non-elderly persons, which indicates the elderly's 1.34 times higher trend compared with the non-elderly's. Third, the pedestrian safety margin (PSM) analysis showed that the PSM of the elderly and the non-elderly were 3.33 seconds and 4.04 seconds respectively, which is 17.5% high. Fourth, the difference in pedestrian safety interval was examined by dividing the speed of approaching vehicle into less than 30km/h, above 30km/h and less than 50km/h, and over 50km/h. There was no significant difference between the PSM of coming vehicles with the speed less than 30km/h and the PSM of approaching with the speed 30km/h~50km/h, but the conflicts with vehicle of the speed above 50km/h show significantly lower PSM than with vehicle speed of 30km/h~50km/h. Finally, when the risk threshold is set to less than 2.5 seconds, the analysis shows that older pedestrians tend to cross roads dangerously 1.59~2.53 times than younger pedestrians. The results set forth here can be used as a basis for constructing the elderly safety measures at present and a potential basis for autonomous vehicle safety application in the future for solving the issue of the difference in crossing behavior between elderly and non-elderly pedestrians.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.13 no.1
• /
• pp.1-14
• /
• 2014

The expansion of the physical road in response to changes in social conditions and policy of the country has reached the limit. In order to alleviate congestion on the existing road to reconsider the effectiveness of this method should be asking. Currently, how to collect traffic information for management of the intersection is limited to point detection systems. Intelligent Transport Systems (ITS) was the traffic information collection system of point detection method such as through video and loop detector in the past. However, intelligent transportation systems of the next generation(C-ITS) has evolved rapidly in real time interval detection system of collecting various systems between the pedestrian, road, and car. Therefore, this study is designed to evaluate the development of an algorithm for queue length based real-time traffic signal control methodology. Four coordinates estimate on time-space diagram using the travel time each individual vehicle collected via the interval detector. Using the coordinate value estimated during the cycle for estimating the velocity of the shock wave the queue is created. Using the queue length is estimated, and determine the signal timing the total queue length is minimized at intersection. Therefore, in this study, it was confirmed that the calculation of the signal timing of the intersection queue is minimized.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.14 no.5
• /
• pp.23-29
• /
• 2015

In this study, human is the subject of driving a car, the actual EEG is a biological information in a number of reactions that are displayed while driving the vehicle by using a measuring device, occurs during travel of the road EEG to be collected, number of experiments the collected material on the basis of changes associated with running time, extracts the factors such as changes due to road geometry, and analysis was performed. The required changes in the EEG occurring during traveling experiment analysis alpha (${\alpha}$) waves, beta (${\beta}$) wave, after the primary extraction in the form of gamma (${\gamma}$) faction, the brain wave frequency of the entire period of the experiment change rate extracts, to calculate the change in frequency in response to EEG characteristics by applying the regression model to observe a learning effect in response to an increase in the number of experiments, as a result, depending on the number of experiments, EEG changes due to individual differences. The show, by repeatedly driving a section like this, it was possible to verify that comfortably travels driver accustomed in accordance with the stored road geometry and signal, safety facilities.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.8 no.5
• /
• pp.59-64
• /
• 2008

The urban is possessing of various landuses such as commercial, industrial, residential and official areas. All of these landuses is including the paved areas that are roads and parking lots. The NPS (nonpoint sources) pollutants are generally originated from pavement areas in urban by human activities. Especially the roads are stormwater intensive landuses because of high vehicle activities and high imperviousness. The main NPS pollutants from roads are particulates and metals from vehicles and pavements. The Korea MOE (Ministry of Environment) is developing the NPS control program to reduce the NPS pollutants from the basins. However, it is not easy to control the NPS because it has high uncertainty by characteristics of rainfalls and watersheds. Therefore, this research was conducted on characterizing the runoff and providing mean EMC from roads. The monitoring were performed for total 16 rainfall events from a road in Youngin City since 2006. The results show that the TSS is highly correlated with other pollutant parameters. The statistical regression models using TSS EMC have been developed to easily determine the EMC of other pollutant parameters.

• Journal of Korean Society of Transportation
• /
• v.27 no.2
• /
• pp.95-105
• /
• 2009

Traffic accidents on highways are likely to happen when there is an imbalance in the complex relationships among key elements such as road geometries, driver related factors, and mechanical performances. The Demand-Effort Model (DEM), which evaluates highway safety, can be explained by the imbalance, which occurs when the level of demand of the driver's attention to the road environment exceeds that of the response from the driver. This study suggests a new model that improves the reliability of the current DEM through the reinterpretation on the physiological signals with the help of the Neural Network Model (NNM). The data were collected from 149 subjects, who drove a test vehicle on the Yongdong, Honam, and Seohaean Expressways in Korea. Three important results could be drawn from the recursive tests as follows; (1) Only 5 out of 10 parameters on the physiological signals which are currently used were proven to be meaningful through the Normality Test, Cluster Analysis, and Mann-Whitney Analysis. (2) The revised DEM, which internally uses the NNM, showed more reliable results than existing DEM. Group 1, which is based on the new DEM showed 80.0% of accuracy in measuring the level of driver's efforts, however, that of Group 2 based on the current DEM was 74.3%. (3) Field tests on the Honam Expressway showed lower 'type II error' with the new DEM (40.5%) than the old DEM (58.8%). The DEM is designed as a quick and easy way to determine highway safety prior to the minute road safety audit (RSA) by a professional audit team. Then a new DEM, which is based on the NNM, needs to be considered since it showed higher reliability and lower error.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.2
• /
• pp.175-181
• /
• 2020

This paper suggests a proper hydraulic filling method in downtown areas. Road subsidence on roadways and sidewalks in downtown areas can result in vehicle damage and casualties. The representative cause of road subsidence is the fraudulent construction in nearby construction sites. A deficiency of excavation restoration causes approximately 25~49% of subsidence. This is performed by equipment or manpower. Hydraulic filling is used in backfilling narrow pipe conduits and spaces between structures. On the other hand, standard specifications and quality assurance standards regarding hydraulic filling principles and construction conditions are insufficient. Therefore, in-door model experiments on hydraulic filling principles, backfilling material, and compaction efficiency were performed. This paper suggests guidelines by investigating and analyzing construction status. In conclusion, thrown backfilling material has a particle size distribution and permeability coefficient as major factors, and detailed standards of the factors are suggested. To improve the compaction efficiency, 90% or more, compaction by the floor should be in units of 0.3m while ensuring a lower drainage layer. When an H-shape stabilizing pile is pulled out after filling, additional hydraulic filling should be in the disturbance range.

• Journal of Korean Society of Transportation
• /
• v.29 no.3
• /
• pp.103-114
• /
• 2011

In this study, we discuss a fatal accident severity model obtained from the analysis of 112 crash sites collected since 2000, and the resulting relationship between fatal accidents and roadway geometry design. From the 720 times computer simulations for improving driving safety, we then reached the following conclusions:. First, the result of cross and frequency-analyses on the car accident sites showed that 43.7% of the accidents occurred on the curved roads, 60.7% on the vertical curve section, 57.2% on the roadways with radius of curvature of 0 to 24m, 83.9% on the roads with superelevation of 0.1 to 2.0% and 49.1% on the one-way 2-lane roads; vehicle types involved are passenger vehicles (33.0%), trucks (20.5%) and buses (14.3%) in order of frequency. The results also show that the superelevation is the most influencing factor for the fatal accidents. Second, employing the Ordered Probit Model (OPM), we developed a severity model for fatal accidents being a function of on various road conditions so as to the damages can be predicted. The proposed model possibly assists the practitioners to predict dangerous roadway segments, and to take appropriate measures in advance. Third, computer simulation runs show that providing adequate superelevation on the segment where a fatal accident occurred could reduce similar fatal accidents by at least 85%. This result indicates that the regulations specified in the Rule for Road Structure and Facility Standard (description and guidelines) should be enhanced to include more specific requirement for providing the superelevation.