• International Journal of Highway Engineering
• /
• v.15 no.1
• /
• pp.143-154
• /
• 2013

PURPOSES: Design of approach roads of rest areas in highway has many drawbacks such as geometric design elements. There has been traffic accidents occured in these approach roads of rest areas. Thus, design criteria is required in order to protect accidents from being occurred. In case of Korea, geometric structure design criteria of entry facilities, such as toll-gate, interchange, junction etc was established. However there are no presence in a detailed standards for geometric structure of the rest area which affiliated road facilities. METHODS: In this study, analytic on accidents was carried out in regards to the entry of geometric structure of resting areas by utilizing a sight survey and an investigation research of traffic accidents. The survey was targeting 135 general service areas. Collisions with physical channelization and safety facilities occurred due to speeding, rapid entry, and etc at the entrance nose section. At the entrance connector roads, accidents caused by speeding, negligence, over-operation of handle of drivers were main reason of accidents. Discriminant analysis were conducted about geometric elements to distinguish influencing factors for traffic accidents. the lengths and access angles of the entrance connector roads were regarded as to have the high relation with traffic accidents. RESULTS: After classifying the design section of resting areas' entry as well as derive design elements on each section, a speed measurement by targeting entry of rest areas and car behavior surveys were performed, then each element's minimum standard was derived through the analyses. According to the speeds at the starting/end point of entrance connector road, the range of the junction setting angle of the entrance connector road is defined as $12^{\circ}{\sim}17^{\circ}$ and the connector length model was suggested. CONCLUSIONS: Suggest improvement plans for existing rest areas that can be applied realistically. This should be corresponded to the standards of entry and exit of developed rest areas.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.1542-1549
• /
• 2011

The Transitional zone between bridge abutment and earthwork is one of the representative vulnerable zones in railway where differential settlements may take place due to the different supportive stiffness. Although transitional zones are managed with stricter standards than those of the other earthwork zones either in the design and construction stages, it is very difficult to prevent differential settlement perfectly. A three-dimensional numerical analyses were performed by applying train moving load in this study. The analytical model including abutments and earthwork zones was constituted with rail, sleepers, track concrete layer (TCL), hydraulic stabilized base (HSB), reinforced road bed, and road bed using railway and road base structure. The clamp connecting the rail and sleeper were also modeled as the element with spring coefficient. The train wheel is modeled in the actual size and moved on the rail with 300 km/hr speed. The deformation characteristics at each point of the rail and the ground were considered in detail when moving the train wheel. The analysis results were compared with those from the two-dimensional analysis without considering moving load. The research results show that displacement and stress were greater in the three-dimensional analysis than in other analyses, and the three-dimensional analysis with moving load should be performed to evaluate railway performance.

• Journal of Korean Society for Geospatial Information Science
• /
• v.10 no.1 s.19
• /
• pp.67-76
• /
• 2002

At a recent, with an increase of traffic demand and a spread of automobile culture, the safety, convenience and speed of highway is required. On this study, using the real time kinematic GPS, observation value at a center line of ready-built road is obtained and then design specification of highway, IP, IA and R are obtained by least square method. Using those IP, IA and R, we analysed the risk factor of highway alignment by the standard for structure and facility of the road. With using RTK GPS, we could analyse dangerous element of highway alignment rapidly and cope with dangerous area of the existing road. It is also proved to apply availably whether we determine alignment improvement is needed or not or analyze source of accident related with alignment in the region having a high traffic accident rate.

• Structural Engineering and Mechanics
• /
• v.82 no.2
• /
• pp.233-244
• /
• 2022

Following a loss of control, the impact against a road barrier in a turn predominates among the most severe motorcyclist accidents. These road restraint devices can be equipped with a motorcycle screen, the function of which is to restrain the rider and minimize the consequences of the impact in terms of the severity of injuries. The performance of these screens is evaluated by the European normative procedure EN1317-8, which specifies the test conditions, based on one or two configurations. In practice, however, these impact conditions are very diverse, difficult to extrapolate from accident analysis and therefore poorly investigated. This study is interested in improving knowledge of these impact conditions in terms of impact speed, impact angle and particularly position of the rider. A finite element model has been developed to simulate the dynamic behavior of the rider from loss of control to impact on the screen. Statistical analysis of the results shows a high variability of the impact conditions, in particular with regard to the direction of turn (to the right or to the left). Some improvements are suggested in order to overcome the limitations inherent in standard procedures.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2003.10a
• /
• pp.187-192
• /
• 2003

of the road would be a key index judged for a safety at the vehicle driving on the road. In Korea, as seen through a lot of documents, the vehicle driving speed is much faster compared with the design speed. The vehicle driving speed is an important element to get to know the vehicle driving characteristics. However, it is not easy to obtain the vehicle driving speed relating to vehicles' consecutive movements just merely through the presently used methods of vehicle driving speed. In consequence, this study has conducted photographing vehicle movements by use of digital moving images. Based on digital moving Images pictured, we have obtained a certain time interval frame and extracted out vehicles' coordinates and calculated vehicle speed from the firstly rectified image and the secondly rectified image. We could obtain comparatively exact results in the calculation of vehicle driving speed as errors of about 4%, as a result of comparison and verification of vehicle speed calculated from the digital moving images and the speed obtained from DGPS.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.3
• /
• pp.166-175
• /
• 2002

Tank track rubbers, which undergo dynamic stresses and strains under various road conditions, leads to a result of considerable internal temperature rise due to the heat generation. Since rubber materials are not fully elastic, a part of the mechanical energy is converted into heat because of the hysteresis loss. Heat generation without adequate heat dissipation leads to heat build-up, i.e. internal temperature rise which, if excessive, exerts a bad influence upon the performance and the life of the tank track rubbers. The purpose of this paper is to predict temperature distributions of the rubber components off tank track subjected to complex dynamic loads under various read conditions. In steady state analysis temperature fields are displayed in contour shapes, and in unsteady analysis the temperature variations of some important nodes are represented graphically with respect to the running time of the tank.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.10a
• /
• pp.91-96
• /
• 2001

When it is considered that many vehicle rides on the road and ride quality is an important method to evaluate vehicle performance with handling, running-over-bump manoeuvre may be suitable for testing ride quality. In this paper, a computed model has roughly steering system and lumped mass, connected by joint each rigid body, and suspension that has beam elements and has shock absorber as force element to represent nonlinear characteristics. A computer simulations for passing over a bump were made with two velocities. One side of vehicle passed over bump in due consideration of driver's habit that driver is subject to avoid a bad ride quality. On simulation, vertical acceleration, pitch angle and roll angle were measured at the mass center of chassis each case.

• Interaction and multiscale mechanics
• /
• v.5 no.4
• /
• pp.347-368
• /
• 2012

Measuring the bridge frequencies indirectly from an instrumented test vehicle is a potentially powerful technique for its mobility and economy, compared with the conventional direct technique that requires vibration sensors to be installed on the bridge. However, road surface roughness may pollute the vehicle spectrum and render the bridge frequencies unidentifiable. The objective of this paper is to study such an effect. First, a numerical simulation is conducted using the vehicle-bridge interaction element to demonstrate how the surface roughness affects the vehicle response. Then, an approximate theory in closed form is presented, for physically interpreting the role and range of influence of surface roughness on the identification of bridge frequencies. The latter is then expanded to include the action of an accompanying vehicle. Finally, measures are proposed for reducing the roughness effect, while enhancing the identifiability of bridge frequencies from the passing vehicle response.

• Interaction and multiscale mechanics
• /
• v.3 no.4
• /
• pp.389-403
• /
• 2010

Based on the Model Coupled Method (MCM), a case study has been carried out on a Concrete-Filled Steel Tubular (CFST) tied arch bridge to investigate the vibration problem. The mathematical model assumed a finite element representation of the bridge together with beam, shell, and link elements, and the vehicle simulation employed a three dimensional linear vehicle model with seven independent degrees-of-freedom. A well-known power spectral density of road pavement profiles defined the road surface roughness for Perfect, Good and Poor roads respectively. In virtue of a home-code program, the dynamic interaction between the bridge and vehicle model was simulated, and the dynamic amplification factors were computed for displacement and internal force. The impact effects of the vehicle on different bridge members and the influencing factors were studied. Meanwhile the acceleration responses of some of the components were analyzed in the frequency domain. From the results some valuable conclusions have been drawn.

• Journal of the Korea Construction Safety Engineering Association
• /
• s.50
• /
• pp.84-96
• /
• 2009

Road is typically constructed along ridge area of mountain because of topographical and economic reasons. Therefore, road may face lots of open cut slope which can easily cause rock falling. This study evaluates the structural safety of newly developed falling rock protection system which has a roof deck plate. The structural performance under self-weight, snow load and load from failing rock was investigated using a finite element numerical analysis method. From the analysis results, the H-beam space was limited not to exceed 2.2m. The deck plate was also safe under the examined loading condition. A hinge and connection in the system were investigated through detailed modelling and analysis. The results showed that the hinge was safe enough and that the connection should strengthened with appropriate stiffeners.