• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.519-524
• /
• 1999

To manufacture alumina products, sintering and grinding process are needed. In Al2O3 grinding, macro/micro surface fracture and cracks are easily occurred on the ground surface because of its high brittleness. In view point of fatigue fracture, surface profile produced by grinding is considered as notches. Therefore, it was reasonable that magnitudes and shapes of surface profiles effects on fatigue strength and life. Particularly, surface finish of Al2O3 which have high hardness and brittleness have an effect on fatigue strength. In this paper, some experiments are carried out to examine influence of grinding conditions to magnitude and shape of surface profile as well as the relationships of Ra, Rmax, Rmax/Ra, and Ku. Through the experimental results, It is found that Ra and Rmax was affected by grinding conditions, but Rmax/Ra and Ku was not. There are linear relations between Ra and Rmax, and between Rmax/Ra and Ku.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1994년도 추계학술대회 논문집
• /
• pp.273-278
• /
• 1994

The surface finishing systems using the micro abrasive film were designed and manufactured to make the mirror surface of the cylindrical workpiece. An experimental study of surface finishing was carried out to investigate the performance of mirror surface finishing system. The surface roughness of stainless steel was about Rmax 0.2~0.25 .mu.m, Ra 0.02~0.04 .mu.m in abrasive grain size 12, 9 .mu.m. the surface roughness of chrome coated workpiece was about Rmax 0.07~ 0.11 .mu. m, Ra 0.01 in abrasive grain size 3 .mu. m. Also, to measure the mirror finishing time by mirror surface finishing system, the experiment was carried out on the chrome coated and ground roller of diameter 76mm and length 650mm. The finishing time and surface roughness were 40min and Rmax 0.1~0.13 .mu.m, Ra 0.01 .mu.m.

• 대한의용생체공학회:의공학회지
• /
• 제18권3호
• /
• pp.301-306
• /
• 1997

간암의 조기 발견으로 인해 간 절제술이 많이 행해지고 있다. 그러나 간을 너무 많이 절제할 경우 수술 후 사망하므로 수술후 잔여 간 기능의 정량적 평가는 외과의에게 매우 중요한 파라미터이다. 그러나 현재 사용하는 ICG Rmax나 Lidocaine clearance test는 시간이 많이 걸리고, 복잡하며, 수술 후 잔여 간 기능의 정량적 평가는 불가능하다. 한편 HEF는 측정의 간편성, 신속성, 비관혈성, 정량성 등의 장점이 있으나 정확성에 의문이 제기되어왔다. 그리하여 본 연구에서는 감마카메라 영상으로부터 HEF를 계산하는 소프트웨어를 개발하여 간을 손상시킨 토끼 18마리와 정상 토끼 6마리를 대상으로 HEF의 정확성을 ICG Rmax 및 MEGX와의 상관계수를 구한 결과 각각 0.91 및 0.94이었다. 그리고 정상인과 비정상인을 대상으로 한 실험에서는 정상군의 HEF는 100% 이상, 비정상군의 HEF는 80% 이하로 나타나 정상군과 비정상군의 구별에 좋은 방법임을 확인하였다. 그리고, 잔여 간 기능의 정량적 평가를 위해 비정상군 중 절제 수술을 시행한 후 생존자를 관찰해 본 결과, 수술 전후의 HEF가 각각 60% 이상인 환자들을 대부분 생존하여 HEF가 60%이면 생존 가능성이 높다는 결론을 내릴 수 있었다.

• 한국자동차공학회논문집
• /
• 제15권4호
• /
• pp.101-107
• /
• 2007

This study investigated the wear of the valve and seat insert seating faces. A tester, an exhaust valve and a seat insert were used. Test variables were cycle numbers ($2{\times}10^6,\;4{\times}10^6,\;6{\times}10^6\;and\;8{\times}10^6$) and Hz (10Hz and 25Hz). The other test conditions such as temperature ($350^{\circ}C$), fuel (LPG) and load (1960N) were fixed. The 10Hz tests indicated that the average Rmax of the valve increased at the rate of $7.76{\mu}m/10^6$ cycles starting from $29.42{\mu}m$ at the $2{\times}10^6$ cycles and that of the seat insert increased at the rate of $8.57{\mu}m/10^6$ cycles starting from $34.19{\mu}m$ at the $2{\times}10^6$ cycles. The 25Hz tests indicated that the average Rmax of the valve increased at the rate of $1.58{\mu}m/10^6$ cycles starting from $74.2{\mu}m$ at the $2{\times}10^6$ cycles and that of the seat insert increased at the rate of $1.25{\mu}m/10^6$ cycles starting from $83.95{\mu}m$ at the $2{\times}10^6$ cycles. The tribochemical reaction product covered the two seating faces, preventing the wear of the seating faces. As cycle numbers became greater, the average Rmax of the seating faces became greater, but the increase rate varied significantly depending on the Hz. The wear mechanism of the two faces was investigated through the tribochemical reaction.

• 한국공작기계학회논문집
• /
• 제15권1호
• /
• pp.82-87
• /
• 2006

The cutting tests of aluminum alloy with heat treatmented various hardnesses after rheo-fonning were carried out using CNC milling machine. The surface roughness(Ra, Rmax) of cut surface and cutting forces are measured at various cutting conditions such as low spindle speed, feed speed and hardness. In the CNC end-milling, the surface roughness increases as feed speed increases and decreases as spindle speed increases. However, the bulit-up edge has occurred on in case of low hardness and low feed speed. In experimental conditions, as the hardness of aluminum alloy increases, the surface roughness(Ra, Rmax) decreases

• 한국세라믹학회지
• /
• 제34권4호
• /
• pp.380-386
• /
• 1997

The tribological properties of ceramics are very important in the application to engineering ceramic parts such as seal rings, pump parts, thread guides, and so on. In this study, the effects of graphite addition on the mechanical and tribological properties of alumina/graphite composites were investigated. The composites were prepared by the adding of graphite powder to the mixture of Al2O3, talc and calcium carbonate. Bending strength, water absorption, friction coefficient, the amount of worn out material at a certain time, and maximum surface roughness(Rmax) of the prepared composites were measured. Crystalline phases and microstructure were examined with XRD and SEM. The melt of Al2O3-CaO-MgO-SiO2 system was shown over 10 vol% graphite composition. As the amount of the graphite is increased, needle like crystals of mullite were formed and grown. We obtained the good properties of friction coefficients and wear resistance at the powder composition containing 15 vol% of graphite.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 후기학술대회논문집
• /
• pp.21-22
• /
• 2005

A study on the wear characteristics of the white metal(Sn-base alloy) bearing as a function of particle contamination level was conducted in order to establish control criteria of the lubricant in the 2-stroke marine diesel engine. Particle contamination level of the lubricants ranged from NAS 10 to 12 for the experiments. Bar-on-plate type wear test was performed using reciprocating wear tester. Based on this study it was found that there was no noticeable difference in weight loss of the white metal for NAS10 and NAS11(particle contamination level). Surface roughness of the white metal bearing after the wear test of 8hrs for the highly contaminated lubricant(NAS12 level) was up to $6{\mu}m$ in Rmax whilst that of the less contaminated lubricants(NAS10 & 11) was less than $1.5{\mu}m$ in Rmax.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1832-1835
• /
• 2003

This paper suggests the selective ultra precision polishing techniques for micro die and mold parts using magnetic-assisted machining. Fabrication of magnetic abrasive particle and their polishing performance are key technology at ultra precision polishing process of micro parts. Conventional magnetic abrasives have disadvantages. which are missing of abrasive particle and inequality between magnetic particle and abrasive particle. So, bonded magnetic abrasive particles are fabricated by several method. For example, plasma melting and direct bonding. Ferrite and carbonyl iron powder are used as magnetic particle where silicon carbide and Al$_2$O$_3$ are abrasive particle. Developed particles are analyzed using measurement device such as SEM. Possibility of magnetic abrasive and polishing performance of this magnetic abrasive particles also have been investigated. After polishing, surface roughness of workpiece is reduced from 2.927 $\mu\textrm{m}$ Rmax to 0.453 $\mu\textrm{m}$ Rmax.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 춘계학술대회 논문집
• /
• pp.646-650
• /
• 1996

In this paper, A hydrostatic bearing spindle for high precision machining and a motor built-in spindle for high speed machining are developed toobtain the high precision machining accuracy of the prototype lathe. The sliding bearing with fluoric resin (turcite) pad is adopted for improving the damping charateristics of guide ways. The funning accuracy of moving elements isestimated to confirm the validity of application on the prototype; the high precision CNC lathe. The surface roughness of Cupper and Aluminum machined by the hydrostatic spindle are 0.07 .mu. m and 0.10 .mu. mRmax. The surface roughness of Aluminium machined by the built-in spindle are 0.10 .mu. mRmax. From this results, it is venified that the prototype lathe is effective to high precision maching.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1873-1876
• /
• 2003

Magneto-rheological polishing is a new technology used in precision polishing. It utilizes magneto-rheological fluid. nonmagnetic polishing abrasive, aqueous carrier fluids in magnetic field to remove material from a part surface. Silicon micro channel as work piece is fixed in the slurry which is made of MR fluid and CeO$_2$(10 vol%) abrasive particles. And permanent magnet rotate in the slurry to transfers magnetic force to abrasive particles by increasing yield strength of MR fluid. so, the obtained bottom surface roughness of micro channel by experiment reduced to Ra 0.010 $\mu\textrm{m}$ Rmax 0.103 $\mu\textrm{m}$ and finwall surface roughness of micro channel reduced to Ra 0.018 $\mu\textrm{m}$ Rmax 0.468 $\mu\textrm{m}$. At optimum conditions of variables, the workpiece as silicon micro channel have about 24 times smaller surface roughness than before polishing.