• Journal of the Korean Society of Clothing and Textiles
• /
• v.18 no.1
• /
• pp.23-30
• /
• 1994

The objective of this study was to analyze the effect of the dissolution of detergent on washing and rinsing efficiency, and the possibility of saving detergent in washing. Washing and rinsing efficiency were reviewed in three different ways : A method was to input dissolved detergent by the use of rapid detergent dissolution instrument, B method was to input dissolved detergent beforehand, and C method was to input undissolved detergent. The results were as follows 1. A method > B method > C method was shown in detergency with washing time and three method's gaps were reduced because detergent dissolution effect was reduced by mechanical action in proportion of washing time. Especially, according to detergency of A method of 0.07% and C method of 0.1% was appeared approximately, saving detergent was expected by rapid dissolution of detergent. 2. A method > B method > C method was shown in detergency with washing temperature. As the washing temperature rose, the detergent reached chemically more activated state and become easily soluble. It resulted for the detergent to penetrate and adhere to laundry easily. 3. A method > B method > C method was shown in detergency with detergent concentration and C method was more sensitive than A, B method against change of detergent cocentration. Rapid detergent dissolution made it possible not only to enhance the washing efficiency but also to save the detergent because detergency of A method in low concentration is higher than that of C method. 4. A method $\geq$ B method > C method was shown in rinsing ratio with detergent input method. It indicated input dissolved detergent was advantageous in rinsing. 5. The result of anion surfactant concentration test of each process with detergent input method was shown like that A method In B method > C method in washing and reverse result was shown in rinsing. The anion surfactant concentration of C method was low during washing but high during rinsing. This was identical with previous results which shown the washing and rinsing efficiency improved with dissolved detergent usasge. 6. C method > B method > A method was shown in the degree of remaining detergent after rinsing. There was no remaining detergent after second rinsing in A and B method, but in C method four rinsings were required for the same result. Consequently, in A and B methods, less water and electricity were used, and less abrasion of cloth.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.4_2
• /
• pp.561-570
• /
• 2023

This study was to evaluate the effect of different rinsing times and methods on the accuracy of temporary prostheses fabricated by 3D printing method. Sixty temporary prostheses were fabricated with LCD types of 3D printer(Halot-Sky, Creality, Shenzhen, China) and divided into six groups (n = 10) based on rinsing times and methods. All specimens were rinsed with 99% isopropanol alcohol for 5 and 10 min using three methods-hand washed, ultrasonic cleaning, and automated washing. All specimens were polymerized for 3 minutes under the same conditions. The marginal and internal gaps of specimens were examined using a replica technique. The light-body silicone thickness was measured at 6 reference points(Absolute marginal discrepancy, Marginal, Chamfer, Axial, Angle, and Occlusal gap). All measurements were performed by a stereomicroscope. Reference point images were taken at 100× magnification and then measured using an image analysis program. Statistical analysis was performed using Two-way ANOVA, One-way ANOVA, and the Kruskal-Wallis test (p = .05). The marginal and internal gaps were statistically different according to the rinsing methods and rinsing times(p < .001). In the rinsing time, the temporary prosthesis rinsed for 5 minutes group showed higher accuracy than 10 minutes group. In the rinsing method, the hand washing group showed higher accuracy than the automated washing group.

• Advances in nano research
• /
• v.1 no.2
• /
• pp.93-103
• /
• 2013

An ultrasonic-mediated assisted stepwise method has been developed for depositing transparent ZnO films from aqueous solution. Rinsing in low ethylene glycol temperature was easy to produce intermediate phase of $Zn(OH)_2$, rinsing in $120^{\circ}C$ ethylene glycol was observed the diffraction peak of intermediate $Zn(OH)_2$ in early report, the rinsing temperature plays an important role in the process of $Zn(OH)_2$ phase transformed to ZnO, high rinsing temperature actually improved the intermediate phase. However, the effect of rinsing on the intermediate phase is yet to be understood clearly. The effect of different rinsing procedures, involving either of or a combination of successive ionic layer adsorption and reaction (SILAR) and ultrasonic-assisted rinsing, prior to hydrolysis in ethylene glycol was found to improve the occurrence $Zn(OH)_2$ in ZnO thin films. In the zinc complex ($[Zn(NH_3)_4]^{2+}$) solution, excess ($[Zn(NH_3)_4]^{2+}$) absorbed in glass substrate transformed incompletely to ZnO and exist as $Zn(OH)_2$ phase in thin films. In films deposited at low temperature, rinsing procedure is applied to improve excess $Zn(OH)_2$ and obtain smoother transparent thin films.

• The Journal of Advanced Prosthodontics
• /
• v.14 no.1
• /
• pp.45-55
• /
• 2022

PURPOSE. This in vitro study investigates the effect of different post-rinsing times and methods on the trueness and precision of denture base resin manufactured through stereolithography. MATERIALS AND METHODS. Ninety clear photopolymer resin specimens were fabricated and divided into nine groups (n = 10) based on rinsing times and methods. All specimens were rinsed with 99% isopropanol alcohol for 5, 10, and 15 min using three methods-automated, ultrasonic cleaning, and hand washing. The specimens were polymerized for 30 min at 40℃. For trueness, the scanned intaglio surface of each SLA denture base was superimposed on the original standard tessellation language (STL) file using best-fit alignment (n = 10). For precision, the scanned intaglio surface of the STL file in each specimen group was superimposed across each specimen (n = 45). The root mean square error (RMSE) was measured, and the data were analyzed statistically through one-way ANOVA and Tukey test (α < .05). RESULTS. The 10-min automated group exhibited the lowest RMSE. For trueness, this was significantly different from specimens in the 5-min hand-washed group (P < .05). For precision, this was significantly different from those of other groups (P < .05), except for the 15-min automated and 15-min ultrasonic groups. The color map results indicated that the 10-min automated method exhibited the most uniform distribution of the intaglio surface adaptation. CONCLUSION. The optimal postprocessing rinsing times and methods for achieving clear photopolymer resin were found to be the automated method with rinsing times of 10 and 15 min, and the ultrasonic method with a rinsing time of 15 min.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.31 no.1
• /
• pp.96-105
• /
• 1989

This laboratory study was performed to produce basic data for the estimation of water requirements for desalinization, through analyzing changes of the electrical conductivity and the exchangeable sodium percentage during the desalinization of reclaimed tidelands. Desalinization experiments were carried out by two water management practices, namely, the leaching method by subsurface drainage and the rinsing method by surface drainage, using samples of silt loam soil and silty clay loam soil collected in reclaimed tidelands. The results obtained from this study were summarized as follows : 1. The sample soils used in this study were saline-sodic soils with the high electrical conductivity and the high exchangeable sodium percentage. 2. Changes of the electrical conductivity and the exchangeable sodium percentage with water requirements for desalinization showed a similar tendency in the desalinization experiment by the same water management practice. 3. The regression equation between the relative electrical conductivity(EC/EC) and water requirements for desalinization(Dw/Ds) could be described by Dw/Ds=O. 29x(EC/EC.) -0.982 (Leaching method), Dw/Ds=3. 678X0. 030(EC/EC ) (Rinsing method). 4. The regression equation between the relative exchangeable sodium percentage (ESP/ESP ) and water requirements for desalinization (Dw/Ds) could be expressed in Dw/Ds = 0.039 x (ESP/ESP. ) - 1. 134 (Leaching method), Dw/Ds=7. 197X0. 024(ESP/ESP ) (Rinsing method). 5. It was estimated that water requirements for the adequate desalinization would be Dw/Ds=0.3 (Leaching method) and Dw/Ds=3.0 (Rinsing method)

• Journal of Technologic Dentistry
• /
• v.42 no.4
• /
• pp.334-340
• /
• 2020

Purpose: This study aimed to compare three-dimensional adaptation with the rinsing time of the temporary crown produced using the digital light processing method. Methods: The maxillary right first molar abutment was scanned with a dental scanner. A temporary crown was designed with the scanned abutment. The designed crown was made of 10 temporary crowns using a digital light processing printer. The crowns were divided into the 5-minute and 10-minute rinsing groups; 5 temporary crown washes were performed for each group. In order to obtain the internal data, each group was scanned for a temporary crown. The three-dimensional fit was measured by superimposing the scanned internal surface data and the abutment data. The average comparison of three-dimensional adaptation was analyzed using the Mann-Whitney U test. Results: The 5-minute rinsing group showed a significantly higher adaptation of 71.42±3.08 ㎛ as compared to the 10-minute rinsing group (67.52±0.92 ㎛) (p<0.05). Conclusion: When making a temporary crown with a digital light processing method, a rinsing time of 10 minutes is appropriate.

• Clean Technology
• /
• v.5 no.1
• /
• pp.78-85
• /
• 1999

In the Kimchi manufacturing industry that has recently been on its greatest growth, the rinsing process for salt-pickled Chinese cabbage in a brining step generates a vast amount of rinsing wastewater containing salts, colloids, and organics released from the raw material. In this study, the experimental method was developed to optimize the rinsing water consumption and thus to minimize the rinsing wastewater generation. The continuous counter-current rinsing basin in the actual plant was simulated through the lab-scale three batch-wise rinsing tanks. Rinsing efficiencies for the brined cabbage from the same brining tank were almost in the same level, whereas those varied substantially from source to source in the raw Chinese cabbage provided. When rinsing water used were decreased from 3.3 L/head to 2.7 L/head, no significant change was observed with respect to COD, turbidity, conductivity, $Na^+$, and $Cl^-$ concentrations in the extracted solution of the rinsed cabbage. However, the quality of the extracted solution was badly deteriorated as the amount of rinsing water used dropped down to below 2.7 L/head. The reduction of rinsing water up to 18% was proved to be possible without any negative effect on the quality of the product, Kimchi.

• Journal of Korea Society of Industrial Information Systems
• /
• v.9 no.4
• /
• pp.8-15
• /
• 2004

Gilding process make thin membrane with other metals to surface of metal and metalloid. It control the hydrogen ion and oxalic acid density with rinsing work since the process used to acid and alkali. Therefore, in this study, several control method applied the gilding process. It desired to the optimal controller and their results can be save on water resource by useful feed of rinsing. And there is quite a possibility of uniform production due to fixed control of acid and alkali. Also it can be contributed the competition power because of lower production unit cost. Especially, this control method to be developed can be applied to any process without mathematical model. And it can be changed their algorithm more easily, if control object is changed.

• The korean journal of orthodontics
• /
• v.24 no.1 s.44
• /
• pp.181-192
• /
• 1994

The effect of topical application on the number of S. mutans was tested in a group of 44 orthodontic patients (mean age, 12Y 3M). They were divided into 5 groups according to the method using NaF and $SnF_2$. The number of S. mutans CFU were counted in stimulated saliva of each subject at baseline, and after one, two, three, and eight weeks. The following results were obtained. 1. In NaF rinsing group, and NaF topical application and NaF rinsing group, the number of S. mutans per ml saliva was not significantly changed. 2. In $SnF_2$ topical application group, and $SnF_2$ topical and NaF rinsing group, the number of S. mutans per ml saliva was significantly reduced. 3. After 8 weeks, there were no significant reduction of the number of S. mutans in comparison with baseline.

• Journal of Environmental Science International
• /
• v.25 no.6
• /
• pp.817-827
• /
• 2016

The resistance in series model has been frequently used for determination of various filtration resistance to correctly understand the membrane fouling behaviour in MBR (membrane bio-reactor) for wastewater treatment. The cake layer resistance ($R_c$) which is commonly determined by calculation of flux dataset that are obtained empirically before and after removing the cake layer on membrane surface. However, the calculated Rc values are very dependent on the cleaning methods adapted for removal of cake layer. This study investigated how the various cleaning options affect $R_c$. Seven different cleaning methods were employed: i) ultrasonication (100 W, 10 min), ii) ultrasonication (200 W, 60 min), iii) ultrasonication (400 W, 120 min), iv) water rinsing in a shaker (100 rpm, 10 min), v) water rinsing in a shaker (300 rpm, 60 min), vi) water rinsing, vii) sponge scrubbing. For the hydrophilic PES membrane, the cake layer removal efficiencies ranged from 64% to 10%, indicating that the removal of cake layer was highly dependent on the cleaning options. For the hydrophobic PVDF membrane, the cake layer removal efficiencies ranged from 79% to 97%. Consequently, a standardized method for cake layer removal to determine cake resistance ($R_c$) is needed for correct interpretation of the fouling phenomena.