• Progress in Medical Physics
• /
• v.9 no.2
• /
• pp.89-94
• /
• 1998

To make practical application of the MR image for stereotactic radiosurgery, the target point-achieved by acquisition of MR image in stereotactic radiosurgery planning system must agree with the actual isocenter of irradiation in real treatment. And the amount of distortion of the MR image must be known to make a correction for the agreement. A radish containing abundant water content was chosen as a homogeneous phantom for the purpose of verification of the agreement in this experiment. A dosimetric film was firmly attached to the small specially fabricated acryl plate and needle puncture was made through the film just into the acryl plate and a drop of oil was dropped into the hole of the film. The acryl plate with film was inserted into the radish and the dorp of oil represented the target point in MR image. After the image acquisition by stereotatic radiosurgery planning system, we achieved stereotactic coordinate of the target point represented by the oil drop. And we proceeded to actual irradiation to the target point according to the procedure of stereotactic radiosurgery. After the irradiation, the film in the radish was developed and processed and the degree of coincidence between the center of the radiation distribution and the target point represented by the hole in the film was measured. The discrepancy between two points was under 0.5 mm. so we could confirm good coincidence in homogeneous phantom such as radish. On the other hand, authors tried to use our home-made device for estimation of distortion of MR image.

• Journal of Life Science
• /
• v.26 no.6
• /
• pp.633-639
• /
• 2016

Biomaterials including polymer, metal, ceramic, and composite have been widely applied for medical uses as medical fibers, artificial blood vessels, artificial joints, implants, soft tissue, and plastic surgery materials owing to their physicochemical properties. However, the biocompatibility and toxicity for film- and plate-form biomaterials is difficult to measure in mammalian cells because there is no appropriate incubation system. To solve these problems, we developed a novel mammalian cell culture system consisting of a silicone ring, top panel, and bottom panel and we applied two polymer films (PF) and one metal plate (MP). This system was based on the principal of sandwiching a test sample between the top panel and the bottom panel. Following the assembly of the culture system, SK-MEL-2 cells were seeded onto Styela Clava Tunic (SCT)-PF, NaHCO₃-added SCT (SCTN)-PF, and magnesium MP (MMP) and incubated at 37℃ for 24 hr and 48 hr. An MTT assay revealed that cell viability was maintained at a normal level in the SCT-PF culture group at 24 or 48 hr, although it rapidly decreased in the SCTN-PF culture group at 48 hr. Furthermore, the cell viability in the MMP culture group was very similar to that of the control group after incubation for 24 hr and 48 hr. Together, these results suggest the sandwich-type mammalian culture system developed here has the potential for the evaluation of the biocompatibility and toxicity of cells against PF- and MP-form biomaterials.

• Korean Journal of Environmental Agriculture
• /
• v.12 no.2
• /
• pp.144-152
• /
• 1993

A bacterium which degrades efficiently synthetic detergents was isolated from the polluted waters, activated sludge of wastewater treatment plants or polluted soil. This bacterium showed considerably higher growth rate in the agar plate containing $2,000{\mu}g/ml$ of synthetic detergents than any other isolated strains, was identified as a Pseudomonas fluorescens or strains similar to it. The strain was named as a Pseudomonas fluorescens S1. Optimum pH and temperature for the growth of the Pseudomonas fluorescens S1 were pH 7.0 and $30^{\circ}C$, respectively. The strain was resistant to streptomycin and gentamycin, but sensitive to kanamycin. The strain was greatly resistant to zinc chloride, lead nitrate and copper sulfate, but unable to grow in the presence of relatively low concentrations of mercury chloride and silver nitrate. This strain utilized benzene, catechol, cyclohexane and xylene as a sole carbon source. The strain was well grown in the medium containing ABS 10,000${\mu}g$/ml. Degradation of ABS was 55% and 60% at 20${\mu}g$/ml and 100${\mu}g$/ml of ABS, respectively. Benzene ring was degraded 45% in 100${\mu}g$/ml of ABS. During the incubation of the strain in the medium containing ABS 100${\mu}g$/ml and COD 10,000${\mu}g$/ml for 4 days, degradation of ABS and COD were reduced to 40${\mu}g$/ml and 3,200${\mu}g$/ml, respectively. Total amino acid content of the Pseudomonas fluorescens S1 grown with 1,000${\mu}g$/ml of ABS was 115mg/g cell, whereas its content was decreased in the bacterium grown without synthetic detergent by 9.4%.

• Journal of Korean Society of Forest Science
• /
• v.88 no.4
• /
• pp.429-437
• /
• 1999

Heavy metals(Cd, Cu, Pb and Zn) in tree rings of P. thunbergii growing at Onsan Industrial Complex of air polluted area were analyzed to study the condition of heavy metal pollution. The tree ring width began to decrease after operation of factories and decreased abruptly at Onsan Industrial Complex after 1991. Cd contents in tree rings showed 119.4ppb to 867.0ppb level and suddenly increased after 1991. Cu contents showed 309.5ppb to 3686.8ppb, and Pb contents 911.33ppb to 7997.1ppb and fluctuations of those were high after operation of factories. Zn contents showed the highest level of 3528.7ppb to 23826.7ppb and largely ascended after 1960, and increased suddenly after 1992, as compared to former tendency. On the other hand, heavy metal contents in tree rings of P. thunbergii at Gosung of non-air polluted area were far lower than Onsan I. C., and there was a wide difference between both areas after 1990. On the heavy metal contents accumulated in bark of P. thunbergii of both areas, it was higher to 10 times in Cd, 1,000 times in Cu, 285 times in Pb and 133 times in Zn contents at Onsan than at Gosung. In the heavy metal analysis for circle plate and cores, heavy metal contents in cores were generally higher than those in disk and Pb contents showed specially high difference, but pattern of variation by tree age showed a similar tendency.

• The Journal of Korean Society for Radiation Therapy
• /
• v.20 no.2
• /
• pp.103-107
• /
• 2008

Purpose: This paper describes a electron field presence of magnetic field, intensity and shape surface dose variation to clinical application possibility. Materials and Methods: The using 6 MeV electron and $10{\times}10\;cm^2$ field size, 9 hole to shielding block make the by measure the film, when the magnetic field position inside and outside of the X-Omat film and parallel plate ionization chamber using the surface dose measured. Results: Present of 4 cm to the side at angle about 3 degree from beam center, use of ring type magnetic is 0.9% increase the surface dose, lens block located in the magnetic field the surface dose 1.58% increase, half magnetic field's position on the side of them at the field center of the 3.6% increase of the surface dose. Conclusion: Surface dose variation is with magnetic field about the mean electron beam of progress direction change, orbit region patient's is inconvenient without surface dose increase percentage case goodness will be used as a useful way.

• Aerospace Engineering and Technology
• /
• v.4 no.2
• /
• pp.171-191
• /
• 2005

This Technical Memo(TM) was written for the purpose of determining the type of UHF-band power divider which is applicable to KSLV-1. For this, some different kinds of power divider are compared with there types and characteristics. And then, we select three types of power divider(which is Wilkinson power divider, Quadrature hybrid divider and Ring hybrid divider) and perform Schematic and Momentum simulation for finding the optimized characteristics. With this results, in order to demonstrate the selected power divider, we manufactured UHF-band power dividers using FR-4 epoxy plate. By the measured results, we obtain the similar results compare with simulation and fabrication. And Quadrature hybrid power divider is suitable to application to KSLV-1.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.2 no.2
• /
• pp.19-24
• /
• 1991

This paper propose a new taegeuk shaped directional couper and verify the possibility of high power division rate in those directional coupler through the experiments. We took the taegeuk shaped structure in those proposed directional coupler to utilize a $3\lambda/4$ section of hybrid ring directional coupler actively, and calculated the branch admittances, which satisfied the condition of perfect matching and isolation in the center frequency, by even odd mode analyzing methodes. On the result, we knew that it can be realized a much higher power division rate than reported result in same circuit area within the producible resistance limit in the microstrip line, made the taegeuk shaped directional couplers with 0, 8, 16 dB power split ratio in the 10 GHz frequency using CGP - 502 plate, and confirmed the validity of theory through the experiments.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.2
• /
• pp.120-126
• /
• 2010

This paper propose analysis and examination of the melting characteristic of fuse elements by repeating overcurrent as a depletion factor of high pressure current limiting fuse through test following existence and nonexistence of extinction material and various configuration of elements. To examine deterioration progress rate by repeating overcurrent we analyzed heat for various element notching configuration, designed plate type, ring type element and estimated the relationship with life span by analyzing breaking characteristic through repeating overcurrent test with adjusting load factor at Silicon Dioxide(SiO2) filled state or in air. A Crack by repeat stress, decrease of section and transformation by friction with extinction material by repeating overcurrent causes a problem which shortens life span based on fuse repeating frequency. Since the contents of this paper might be useful to research the correlation between friction of materials and repeating life span based on load factor of repeating current, the quality of product would be improved through solution of the problem.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.1
• /
• pp.9-15
• /
• 2008

Mokumegane is one of the sophisticated metal craft techniques enabling wood grain surface effect. To embody the mokumegane, an ingot of well-bonded stacked metal plates has been required. Traditionally prepared mokumegane ingots were bonded using charcoal which enables reduction atmosphere, but sometimes end up with collapse of bonding interface due to the lack of reliable process control. We proposed a systematic vacuum direct bonding process for ingots. First, we confirmed copper//copper homogeneous plate bonding at $900^{\circ}C$ by applying uniaxial press of 2.5kg. We observed 80min required to obtain 90%-bonding ratio and the diffusion coefficient would be enhanced up to 100 times due to surface effect. Second, by considering enhanced diffusion behavior, we also obtained optimum bonding condition in copper/silver heterogeneous plates that ensures 90%-bonding ratio at $700^{\circ}C$ for 10min with apply uniaxial press. A 7-layered copper/silver ingot is prepared successfully, and eventually the prototype mokumegane cases for mobile phone were fabricated with these ingot.

• Journal of the Korean Vacuum Society
• /
• v.5 no.2
• /
• pp.139-146
• /
• 1996

Transparent and conducting Sb-doped $SnO_2$ thin films were prepared by rf magnetron sputtering technology. But it showed a serious damage phenomenon on the surface of as-deposited films. In order to avoid a damage caused in the substrate center and location facing to target erosion, a ring plate of masking glass was installed at 1.5 cm above target surface. The uniformity and electrical characteristic of $SnO_2$ thin films were evaluated by the control of optimal conditions in the magnetron sputtering operation such as rf power, sputtering gas pressure, and substrate temperature. In the experimental results using the operating conditions, the optimum temperature, which produced uniform and damageless films, shifted with the change of gas pressure. The rate was about $100^{\circ}C$/5 mTorr at rf power of 50 W Similarly, the optimum temperature in compensation for an increase of rf power shifted down to a proper rate.