• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.8
• /
• pp.28-34
• /
• 2000

Pyroelectric properties of the $Pb(Zr_{0.9}Ti_{0.1})O_3$ ceramics having the rhombohedral structure have been studied by using the dynamic measurement method. The pyroelectric responses of the $Pb(Zr_{0.9}Ti_{0.1})O_3$ ceramics are characterized in both low and high medulation frequency regions and their frequency depences are observed. In the low frequency region (2~200Hz), the change of polarization increases and shows the maximum since the reorientation rate of domains is higher than the modulation frequency. Inthe high frequency region (200~2000Hz), the pyroelectrci response decreases as the frequency increases, because the reorientation of domains is suppressed and so the change of polarization decreases. Pyroelectric coefficient, figure of merit, noise equivalent power and detectivity of the $Pb(Zr_{0.9}Ti_{0.1})O_3$ ceramics are measured as $1.6{\times}10^{-8}C/cm^2{\cdot},\;1.6{\times}10^{-11}C{\cdot}cm/J,\;2.4{\times}10^{-7}W/Hz^{1/2}\;and\;4.17{\times}10^6cm{\cdot}Hz^{1/2}/W$, respectively.

• Journal of the Korean Magnetics Society
• /
• v.5 no.4
• /
• pp.275-280
• /
• 1995

The sites for $Fe^{+3}$ are partly substituted by $Co^{+2}$ and $Ti^{+4}$ cations to control coercivity of Ba-ferrite particles for use in high density magnetic recording. The substituted $Co^{+2}$ cation has very much different effects on magnetic properties and particle characteristics from that $Ti^{+4}$ cation has. The decrease in the coercivity with the $Co^{+2}$ substitution is attributed to the formation of excessive spinel-block(S-block) in pure Ba-ferrite crystal, while saturation magnetization is increased and the distributions of coercivity and particle size become broad. The substitution with the $Ti^{+4}$ decreases the sauration magnetization, but has less effect on a change in coercivity than the $Co^{+2}$. The $Ti^{+4}$ acts as a nucleation agent in amorphous phase of formulated compound, and consequently particle size and aspect ratio are decreased. Furthermore, the enhancement of substitution of the $Co^{+2}$ for the $Fe^{+3}$ sites in rhombohedral-block(R-block) by the $Ti^{+4}$ retards the nucleation of spinel phase of Ba-ferrite, which results in uniform magnetic properties of Ba-ferrite particles. It is suggested that the contents of the cations to be substituted for the $Fe^{+3}$ sites are optimized on the bases of magnetic properties and particle characteristics rather than on the base of electrical charge balance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.138-141
• /
• 2004

[ $MnO_2$ ]가 첨가된 $0.9Pb(Zr_{0.5}Ti_{0.5})O_3-0.2Pb[(Zn_{0.8}Ni_{0.2})_{1/3}Nb_{2/3}]O_3$(0.8PZT-0.2PZNN) 세라믹스는 그 압전특성과 유전특성이 뛰어나지만 $1000^{\circ}C$ 이하의 낮은 소결 온도에서는 소결되지 않는다. $1000^{\circ}C$이하의 낮은 소결온도에서 소결하기 위해 CuO를 첨가한 결과, 소결온도 $920^{\circ}C$에서 소결성은 우수하였으나 그 압전 특성의 저하가 두드러졌다. 이는 XRD에서 확인한 결과에 따르면 CuO의 첨가가 우수한 MPB 조성으로 판명된 $MnO_2$ 가 첨가된 0.8PZT-0.2PZNN 세라믹스의 결정구조를 Rhombohedral 구조로 바꾸기 때문인 것으로 보였으며 이러한 문제는 PZNN의 비율을 조절하여 0.875PZT-0.125PZNN 세라믹스를 선택함으로 인해 해결할 수 있었다. 그러나 여전히 낮은 $Q_m$값을 높이기 위해서 $Al_2O_3$를 첨가하였고 그 결과 시편의 tetragonality 감소와 $Q_m$값의 증가를 확인할 수 있었으나 그 첨가량이 0.2wt% 이상일 경우에는 밀도의 감소로 인한 압전특성의 저하가 나타났다. 밀도의 향상을 위해 Zn and Ni excess 조성을 선택하였고 그 결과 0.5wt% $MnO_2$와 0.2wt% CuO 그리고 0.3wt% $Al_2O_3$를 첨가한 0.875PZT-0.125PZNN 세라믹스(Zn and Ni excess 조성)를 $920^{\circ}C$에서 소결한 경우 $k_p=0.581,\;Q_m=809,\;d_{33}=345\;pC/N\;and\;{\varepsilon}_{33}/{\varepsilon}_0=1345$의 빼어난 압전 및 유전특성과 $330^{\circ}C$의 높은 $T_c$를 보였고 그 조성의 vibration velocity는 약4.5 m/s로 나타났다.

• Journal of the Mineralogical Society of Korea
• /
• v.30 no.4
• /
• pp.179-186
• /
• 2017

This study investigated the mineralogical characteristics of lime mortars used in pointing of Namhansanseon Yeojang from Joseon dynasty. Polarization microscopy revealed quartz, feldspar, mica, pyroxene and opaque minerals in the lime mortars. XRD analysis also confirmed clay minerals chlorite and kaolin. As a result of particle size analysis of lime mortars, the particle size distribution was wide and size was not uniform. 60% of samples were corresponded to the sand area. The chemical components detected from XRF analysis, 8.71-11.18 % of Ca as the main component of lime and $SiO_2$, $Al_2O_3$, and $Fe_2O_3$ in soil minerals were main components. The lime mortars showed an endothermic peak due to decarbonization reaction of $CaCO_3$ at $750^{\circ}C$ and weight reduction rate of 10%. The microstructures were agglomerated amorphous and observed rhombohedral calcite crystals by scanning electron microscope. It is considered that the pointing of Yeojang is a mortar mixed with lime and soil. In addition the Hanbongseong Yeojang was constructed using the same materials and construction technique because the minerals composition is not different according to the Yeojang location and use.

• Applied Chemistry for Engineering
• /
• v.9 no.5
• /
• pp.654-660
• /
• 1998

In preparing PSZT powder by hydrothermal synthesis, effects of reaction temperature, concentration of raw materials and mineralizer on crystallinity, particle size distribution, and dielectric constant were investigated. By varying the concentration of mineralizer and the ratio of Pb to Sr or Zr to Ti, crystalline PSZT powder, having the mean particle size of $0.3{\sim}15{\mu}m$, was prepared by hydrothermal synthesis in the temperature range of $120{\sim}200^{\circ}C$ for a 2h reaction. PSZT ceramics, having dielectric constant of 1000~3000, were prepared at $1150^{\circ}C$ for a 2h sintering reaction of the PSZT powders. Experimental results showed that the weight mean particle size of $0.5{\mu}m$ was obtained when the concentration of KOH in the solution was 10 wt % and the ratio of Pb to Sr was 0.95/0.05, that of Zr to Ti was 0.52/0.48. It also showed that the ceramics of dielectric constant of 2900 were prepared through sintering of this PSZT powder. Size of PSZT particles became smaller with its narrow distribution as the concentration of KOH increased up to 10 wt %. However, it came to be larger at this concentration and above. By adding small amount of Sr that would not affect that crystallinity of particles we can improve dielectric property of sintered materials. Addition of Zr may shift the major crystal phase of synthetic PSZT powder from tetragonal to rhombohedral phase.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.5
• /
• pp.18-38
• /
• 2002

A previous study on the model coatings based on latex-bound plastic pigment coatings (1) has been extended to latex-bound No. 1 clay, ultra-fine ground calcium carbonate (UFGCC), and clay-carbonate pigment mixture coatings, which are being widely used in the paper industry. The latex binder used was a good film-forming, monodisperse S/B latex or 0.15$\mu\textrm{m}$. No. 1 clay was representative of plate-like pigment particles, whereas UFGCC was of somewhat rounded rhombohedral pigment particlel. Both of them had negatively skewed triangular particle size distributions having the mean particle suet of 0.7${\mu}{\textrm}{m}$ and 0.6$\mu\textrm{m}$, respectively. Their packing volumes were found to be 62.5% and 657%, respectively. while their critical pigment volume concentrations (CPVC's) were determined to be 52.7% and 50.5% ( average of 45% caused by the incompatibility and 55.9% extrapolated) by coating porosity, respectively. Each pigment/latex coating system has shown its unique relationship between coating properties and pigment concentrations, especially above its CPVC. Notably, the clay/latex coating system hat shown higher coating porosity than the UFGCC/latex system at high pigment concentrations above their respective CPVC's. It was also found that their coating porosity and gloss were inter-related to each other above the CPVC's, as predicted by the theory. More interestingly, the blends of these two pigments have shown unique rheological and coating properties which may explain why such pigment blends are widely used in the industry. These findings have suggested that the unique structure of clay coatings and the unique high-shear rheology of ground calcium carbonate coatings can be judiciously combined to achieve superior coatings. Importantly, the low-shear viscosity of the blends was indicative of their unique packing and coating structure, whereas their high-shear rheology was represented by a common mixing rule, i.e., a viscosity-averaging. Transmission and scanning electron and atomic force microscopes were used to probe the state of pigment / latex dispersions, coating surfaces, freeze fractured coating cross-sections, and coating surface topography. These microscopic studies complemented the above observations. In addition, the ratio, R, of CPVC/(Pigment Packing Volume) has been proposed as a measure of the binder efficiency for a given pigment or pigment mixtures or as a measure of binder-pigment interactions. Also, a mathematical model has been proposed to estimate the packing volumes of clay and ground calcium carbonate pigments with their respective particle size distributions. As well known in the particle packing, the narrower the particle size distributions, the lower the packing volumes and the greater the coating porosity, regardless of particle shapes.

• Korean Chemical Engineering Research
• /
• v.57 no.2
• /
• pp.205-209
• /
• 2019

The exquisite structure and attractive biological properties of biominerals have great potential and increased interest for use in a wide range of medical and industrial applications. Calcium carbonate biomineralization, mainly controlled by shell matrix proteins, has been used as a representative model to understand the biomineralization mechanism. In this study, in vitro calcium carbonate crystallization was carried out under room temperature and atmospheric pressure using recombinant shell matrix protein GRP_BA and artificial shell matrix protein GG1234. Both proteins inhibited the growth of typical rhombohedral calcite crystals in the calcium carbonate crystallization using $CaCl_2$ solution and $(NH_4)_2CO_3$ vapor, and spherulitic calcite crystals with rosette-like structures were synthesized in both the presence of GRP_BA and GG1234. These results might be caused by the properties of block-like domain structure and intrinsically disordered proteins. We expect that this study can contribute to enhance understanding of the calcium carbonate biomineralization controlled by shell matrix proteins.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.3
• /
• pp.249-254
• /
• 2023

La_0.7-xCe_xSr_0.3MnO₃ specimens were fabricated by a solid state reaction method and structural and electrical properties with variation of Ce⁴⁺ contents were measured. All specimens exhibited a polycrystalline rhombohedral crystal structure, and the (110) peaks were shifted to low angle side with increasing the amount of Ce⁴⁺ contents. As Ce⁴⁺ ions with different ion radii and charges are substituted with La³⁺ ions, electrical properties are thought to be affected by changes in the double exchange interaction between Mn³⁺-Mn⁴⁺ ions due to distortion of the unit lattice, a decrease in oxygen vacancy concentration, and an increase in lattice defects. Resistivity gradually decrease as the amount of Ce⁴⁺ added increased, and negative temperature coefficient of resistance (NTCR) properties were shown in all specimens. In the La_0.5Ce_0.2Sr_0.3MnO₃ specimens, electrical resistivity, TCR and B-value were 31.8 Ω-cm, 0.55%/℃ and 605 K, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.36 no.3
• /
• pp.275-279
• /
• 2023

La_0.7Sr_0.3-xMg_xMnO₃ (LSMMO) (x=0.05~0.20) specimens are fabricated by a solid phase sintering method, and the sintering temperature and time are 1,300℃ and 2 hours, respectively. The dependence of the crystalline structure according to the amount of Mg²⁺ contents is not observed, and all specimens show a polycrystalline rhombohedral crystal structure, the X-ray diffraction (110) peaks move to the high angle side with increasing the amount of Mg²⁺ contents. LSMMO specimens exhibit a granule-shaped microstructure with an average grain size of 1 ㎛ or less. Resistivity gradually decrease as the amount of Mg²⁺ contents increased. And in the La_0.7Sr_0.1Mg_0.2MnO₃ specimen, resistivity and B_25/65-value are 36.7 Ω-cm and 394 K at room temperature, respectively. LSMMO specimens show a variable-range hopping (VRH) electrical conduction mechanism, and the negative temperature of coefficient of resistance (NTCR) is approximately 0.37~0.38%/℃.

• Progress in Medical Physics
• /
• v.20 no.2
• /
• pp.80-87
• /
• 2009

Phase transformation, superelastic characteristics and variation of surface residual stress were studied for Nitinol shape memory alloy through application of UNSM technology, and life extension methods of stent were also studied by using elastic resilience and corrosion resistance. Nitinol wire of ${\phi}1.778$ mm showed similar surface roughness before and after UNSM treatment, but drawing traces and micro defects were all removed by UNSM treatment. It also changed the surface residual stress from tensile to compressive values, and XRD result showed less intensive austenite peak and clear martensite and additional R-phase peaks after UNSM treatment. Fatigue resistance could be greatly improved through removal of surface defects and rearrangement of surface residual stress from tensile to compressive state, and development of surface modification system to improve not only bio-compatability but also resistance to corrosion and wear will make it possible to develop vascular stent which can be used for circulating system diseases which run first cause of death of recent Koreans.