• 유변학
• /
• 제11권2호
• /
• pp.105-111
• /
• 1999

감쇠기는 기계 시스템에서 에너지를 소모하는데 사용되는 요소이다. 이러한 감쇠기에는 수동 감쇠기, 능동 감쇠기, 반능동 감쇠기 등의 종류가 있다. 반능동 감쇠기는 수동 감쇠기에 비해서 더 좋은 성능을 내면서 능동 감쇠기보다는 더 작은 동력원을 필요로 하는 장치로 상황에 따라서 그 감쇠력 특성을 변화 시킬 수 있다. 본 논문은, 자기 유변 유체를 이용한 반능동 감쇠기의 개발에 관한 것이다. 자기 유변 유체는 가제어성 유체의 일종으로 인가 자기장에 대해서 그 유동학적 성질이 변하며 높은 항복응력, 낮은 점성계수, 불순물에 대한 안정성과 넓은 사용 온도 범위 등의 장점을 가진 재료이다. 이를 이용할 경우 간단한 구조로 반능동 감쇠기를 설계할 수 있을 뿐만 아니라 빠른 응답성 등의 효과도 기대할 수 있다. 본 연구에서는 자기 유변 유체를 이용하여 설계·제작된 몇 가지 종류의 감쇠기들을 통하여 그 응용 방법과 범위 그리고 응용 시 수반되는 문제점 등을 제시하였다.

• International Journal of Industrial Entomology and Biomaterials
• /
• 제26권2호
• /
• pp.81-88
• /
• 2013

Wet-spun silk fibers have attracted the attention of many researchers because of 1) the unique properties of silk as a biomaterial, including good biocompatibility and cyto-compatability and 2) the various methods available to control the structure and properties of the fiber. Cellulose nanofibrils (CNFs) have typically been used as a reinforcing material for natural and synthetic polymers. In this study, CNF-embedded silk fibroin (SF) nanocomposite fibers were prepared for the first time. The effects of CNF content on the rheology of the dope solution and the characteristics of wet-spun CNF/SF composite fibers were also examined. A 5% SF formic acid solution that contained no CNFs showed nearly Newtonian fluid behavior, with slight shear thinning. However, after the addition of 1% CNFs, the viscosity of the dope solution increased significantly, and apparent shear thinning was observed. The maximum draw ratio of the CNF/SF composite fibers decreased as the CNF content increased. Interestingly, the crystallinity index for the silk in the CNF/SF fibers was sequentially reduced as the CNF content was increased. This phenomenon may be due to the fact that the CNFs prevent ${\beta}$-sheet crystallization of the SF by elimination of formic acid from the dope solution during the coagulation process. The CNF/SF composite fibers displayed a relatively smooth surface with stripes, at low magnification (${\times}500$). However, a rugged nanoscale surface was observed at high magnification (${\times}10,000$), and the surface roughness increased with the CNF content.

• Korea-Australia Rheology Journal
• /
• 제14권3호
• /
• pp.107-114
• /
• 2002

Residual stress distribution in injection molded short fiber composites is determined by using the layer-removal method. Polystyrene is mixed with carbon fibers of 3% volume fraction (4.5% weight fraction) in an extruder and the tensile specimen is injection-molded. The layer-removal process, in which removing successive thin uniform layers of the material from the surface of the specimen by a milling machine, is employed and the resulting curvature is acquired by means of an image processing. The isotropic elastic analysis proposed by Treuting and Read which assumes a constant Yaung’s modulus in the thickness direction is one of the most frequently used methods to determine residual stresses. However, injection molded short fiber composites experience complex fiber orientation during molding and variation of Yaung’s modulus distribution occurs in the specimen. In this study, variation of Yaung’s modulus with respect to the thickness direction is considered for calculation of the residual stresses as proposed by White and the result is compared with that by assuming constant modulus. Residual stress distribution obtained from this study shows a typical stress profile of injection-molded products as reported in many literatures. Young’s modulus distribution is predicted by using numerical methods instead of experimental results. For the numerical analysis of injection molding process, a hybrid FEM/FDM method is used in order to predict velocity, temperature field, fiber orientation, and resulting mechanical properties of the specimen at the end of molding.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.441-443
• /
• 2008

A non-vacuum process for fabrication of $CuInSe_2$ (CIS) absorber layer from the corresponding Cu, In solution precursors was described. Cu, In solution precursors was prepared by a room temperature colloidal route by reacting the starting materials $Cu(NO_3)_2$, $InCl_3$ and methanol. The Cu, In solution precursors were mixed with ethylcellulose as organic binder material for the rheology of the mixture to be adjusted for the doctor blade method. After depositing the mixture of Cu, In solution with binder on Mo/glass substrate, the samples were preheated on the hot plate in air to evaporate remaining solvents and to burn the organic binder material. Subsequently, the resultant CI/Mo/glass sample was selenized in Se evaporation in order to get a solar cell applicable dense CIS absorber layer. The CIS absorber layer selenized at $530^{\circ}C$ substrate temperature for 30 min with various Se gas evaporation temperature was characterized by XRD, SEM, EDS.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 춘계학술대회 논문집
• /
• pp.19-22
• /
• 2009

A non-vacuum process for fabrication of $CuIn_xGa_{1-x}Se_2$ (CIGS) absorber layer from the corresponing Cu, In, Ga solution precursors was described. Cu, In, Ga precursor solution was prepared by a room temperature colloidal route by reacting the starting materials $Cu(NO_3)_2$, $InCl_3$, $Ga(NO_3)$ and methanol. The Cu, In, Ga precursor solution was mixed with ethylcellulose as organic binder material for the rheology of the mixture to be adjusted for the doctor blade method. After depositing the mixture of Cu, In, Ga solution with binder on Mo/glass substrate, the samples were preheated on the hot plate in air to evaporate remaining solvents and to burn the organic binder material. Subsequently, the resultant CIG/Mo/glass sample was selenized in Se evaporation in order to get a solar cell applicable dense CIGS absorber layer. The CIGS absorber layer selenized at $530^{\circ}C$ substrate temperature for 1h with various metal organic ratio.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 춘계학술대회
• /
• pp.222-224
• /
• 2006

A non-vacuum process for $Cu(In,Ga)Se_2$ (CIGS) thin film solar cells from nanoparticle precursors was described in this work CIGS nanoparticle precursors was prepared by a low temperature colloidal route by reacting the starting materials $(CuI,\;InI_3,\;GaI_3\;and\;Na_2Se)$ in organic solvents, by which fine CIGS nanoparticles of about 20nm in diameter were obtained. The nanoparticle precursors were mixed with organic binder material for the rheology of the mixture to be adjusted for the doctor blade method. After depositing the mixture of CIGS with binder on Mo/glass substrate, the samples were preheated on the hot plate in air to evaporate remaining solvents ud to burn the organic binder material. Subsequently, the resultant (porous) CIGS/Mo/glass simple was selenized in a two-zone Rapid Thermal Process (RTP) furnace in order to get a solar ceil applicable dense CIGS absorber layer. Complete solar cell structure was obtained by depositing. The other layers including CdS buffer layer, ZnO window layer and Al electrodes by conventional methods. The resultant solar cell showed a conversion efficiency of 0.5%.

• 소성∙가공
• /
• 제14권4호
• /
• pp.319-326
• /
• 2005

In this study, the nano-deformation behavior of semi-solid Al-Si alloy was investigated using a molecular dynamics simulation as a part of the research on the surface crack behavior in thixoformed automobile parts. The microstructure of the grain-size controlled Al-Si alloy consists of primary and eutectic regions. In eutectic regions the crack initiation begins with initial fracture of the eutectic silicon particles and inside other intermetallic phases. Nano-deformation characteristics in the eutectic and primary phase of the grain-size controlled Al-Si alloy were investigated through the molecular dynamics simulation. The primary phase was assumed to be single crystal aluminum. It was shown that the vacancy occurred at the zone where silicon molecules were.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.569-574
• /
• 2002

Generally, the limestone powder is known to have some advantages in rheology of fresh concrete, resistance of material separation, and enhancement of strength at early ages. Recently, great attention is being paid to limestone blended cements in the manufacture of concrete, especially in the countries of Europe. The purpose of the present study is to establish the mechanical and durable properties of concrete containing slag and limestone powder. In this paper, the chloride ion penetration test, rapid carbonation test and rapid freezing-thawing test is carried out to study durability of concrete with various content of limestone powder. Futhermore, the strength of concrete is evaluated with various ages.

• Advances in materials Research
• /
• 제3권2호
• /
• pp.91-103
• /
• 2014

A study that demonstrates how to investigate the molded part quality and the consistency of injection process based on the rheological concept is proposed. It is important for plastic material whose melt viscosity is variable with respect to the processing condition. The formulations to couple the melt viscosity with injection pressure and fill time are derived first. Taking calculations of the measured pressure and the time by using these formulations, the melt viscosity in injection process can be determined on machine. As the relation between the injection speed and the melt viscosity is constructed, the influences of the setting parameter of injection machine on the molded part quality can be investigated through evaluating the state of the melt viscosity. In addition, a pressure sensor bushing (PSB) designed with a quick installation feature is also provided and validated. The results show that a higher injection speed improves the tensile strength of the molded part but also the consistency of the molded part quality. This work provides an alternative to evaluate the molding quality scientifically.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 춘계학술발표대회
• /
• pp.1.2-1.2
• /
• 2011

With recent advances in materials and products, materials processing experiences new challenges. More particles and polymers in material side and thinner and faster deformations in processing side. It happens in most emergying industries such as manufacturing of batteries, solar cells, multi-layer chips, displays, printed electronics, to list a few. In most cases, they are manufactured by coating or printing process, which is defined as a process in which gas is replaced by liquid on a substrate. In this sense, casting, inkjet printing, and roll-to-roll printing are all included. The printing process consists of three unit processes. As the materials used in the above mentioned applications typically contain a large amount of particles with polymers and solvents, they continuously change microstructures during preparation, flow, and even drying. However, little is known about the flow characteristics of such complex fluids and less is known about how to design and control the process. Therefore, for better control of the process and for better quality of the product, we need to understand the flow characteristics of these complex fluids under extremely fast flow environment.