• Korean Journal of Food Science and Technology
• /
• v.21 no.1
• /
• pp.75-79
• /
• 1989

The rheological properties of sugar and cocoa particle suspensions in cocoa butter under molten condition were analyzed with Haake rotationary viscometer. Both suspensions had yield value and showed rheopexy at low shear rate and thixotropy at high shear rate. Flow behaviors of the suspensions were analyzed with modified Casson model. Casson viscosity and yield value increased with increasing the concentration of sugar and cocoa particles. There was an obvious dependence of the Casson viscosity and yield value on the particle size distributions that was represented by the Sauter mean diameter of the particles. Casson viscosity and yield value of cocoa butter-sugar suspension increased with increasing the fineness of sugar particle crystal. With increasing the fineness of cocoa particle a decreasing Casson viscosity of cocoa butter-cocoa particle suspension was achieved, but the yield value did not change significantly with cocoa particle size. Therefore, it was predicted that the best rheological properties of chocolate could be obtained with the combination of coarse ground sugar $(d=36.30{\mu}m)$ and fine ground cocoa particle $(d=14.81{\mu}m)$ within the studied range.

• Archives of Pharmacal Research
• /
• v.8 no.2
• /
• pp.91-98
• /
• 1985

Dependence of the flow behavior of aqueous suspension of Young-Il bentonite on the concentration and the type of electrolytes was studied. Viscosity measurements were made was Rion Viscotester, using No. 3 rotor at 62.5 R. P. M. at 25.deg.C. As electrolyte concentration increased, the apparent viscosity was observed to increase. Changes in viscosity were in general agreement with predicted results based on the Hofmeister sequence and the Schulze-Hardy rule. The observed electrolyte effect on the apparent viscosity was discussed in terms of the Verwey-Overbeek theory.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.1
• /
• pp.41-49
• /
• 2021

3D printing techniques have been recently adopted in the construction industry. It mainly utilizes additive manufacturing which is the fabrication process depositing successive layers of materials without any formworks. Conventional cementitious materials may not be directly applicable to 3D printing because 3D printable cementitious materials is required to satisfy such characteristics as pumpability, extrudability, and buildability in a fresh state. This study aimed to investigate rheological properties and required performances of 3D printable cementitious materials, by reviewing existing studies. Test methods and equipments, evaluation results and characteristics of mixture additives were compared. Based on reviews of existing studies, this study indicates that the viscosity is mainly relevant to the pumpability of 3D printable materials whereas the yield stress and thixotropy are important in securing buildability of the materials.

• Advances in concrete construction
• /
• v.13 no.4
• /
• pp.281-289
• /
• 2022

3D printing cement-based materials (3DPCBM) is an innovative rapid prototyping technology for construction materials. This study is tested on the rheological behavior, printability and buildability of steel slag (SS) content based on the extrusion system of 3D printing. 0, 8 wt%, 16 wt%, 24 wt%, 32 wt% and 40 wt% SS was replaced cement, The test results revealed that the addition of SS would increase the fluidity of the printed paste, prolong the open time and setting time, reduce the plastic viscosity, dynamic yield stress and thixotropy, and is beneficial to improve the pumping and extrudability of 3DPCBM. With the increase of SS content, the static yield stress developed slowly with time which indicated that SS is harmful to the buildability of printing paste. The content of SS in 3DPCBM can reach up to 40% at most under the condition of satisfying rheological property and buildability, it provides a reference for the subsequent introduction of SS and other industrial solid waste into 3DPCBM by explored the influence law of SS on the rheological properties of 3DPCBM.

• YAKHAK HOEJI
• /
• v.35 no.4
• /
• pp.319-325
• /
• 1991

Aluminum phosphate gel was synthesized by reacting aluminum sulfate as a soluble aluminum salt to tribasic sodium phosphate in this study. The optimal synthesis conditions based on the yield of product were investigated by applying Box-Wilson experimental design. It was found that optimal synthesis conditions were as follows: Reaction temperature; $61~71^{\circ}C$, concentration of two reactants; 12.27~13.83%, concentration ratio of two reactants; [AI$_{2}$(SO$_{4}$)$_{3}$]/[Na$_{3}$PO$_{4}$]= 0.5, reaction time; 10.9~12.1 minutes, drying temperature of product; $60~72^{\circ}C$. Aluminum phosphate gel prepared by the optimal synthesis conditions was suspended with four types of natural and synthetic gums at the concentration of 0.375~1.5wv%. Their Theological properties of aluminum phosphate gels were examined with Haake-Rotovisco RV 20 rotational viscometer. It showed that the higher concentration of suspending agents and lower temperature, the higher viscosity. Aluminum phosphate gel suspended by pectin and agar showed plastic flow with rheopexy, and their gels suspended by sodium alginate and sod. CMC showed plastic flow with thixotropy.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.11a
• /
• pp.721-724
• /
• 2006

In this study, particle size distribution of cement powder system were adjusted using the blast furnace slag powder, Blaine $2250cm^2/g\;and\;8300cm^2/g$, which easy to adjust particle size distribution to examine how particle size distribution of the binder has an effect on rheological properties of the cement paste. In addition, the relationship between n-value of Rosin-Rammler function and plastic viscosity were discussed. All measured flow curves represented thixotropy behavior and the hysteresis area was smaller for the more added coarse particle. When the combination was based on a ratio of $20{\sim}25vol%$ fine particles, $30{\sim}40vol%$ OPC and $40{\sim}45vol%$ coarse particles of the total volume, a high fluidity and low yield strength was achieved.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.21 no.1
• /
• pp.71-80
• /
• 2003

Printing inks are mainly composed of pigment and vehicles. Among these components, the Vehicle affect the rheologic property of the ink the most but pigment content or characteristic also affect to the fluidity property not less than the vehicle. In the study, with the same vehicle on each sample, by making the sample to increase pigment content gradually. It can be examined the influence of the pigment to the fluidity of ink. In result we found that the viscosity value of the low shear rate rang has relatively higher value with increasing the pigment content in the ink. According to higher pigment content, yield stress and thixotropy index increases gradually. Structure recovery of the ink is that, the higher pigment content's ink, the less changing shear rate, and it takes less time to recover.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.35 no.2
• /
• pp.103-110
• /
• 2009

The objective of this study is to analyze the influences of fatty alcohols and fatty acids on rheological properties of oil in water (O/W) emulsions using viscosity and rheograms. As the chain length of fatty alcohols and fatty acids lengthened, the viscosity of emulsions was increased. The influence of fatty alcohols on viscosity enhancement was stronger than that of fatty acids. Both stearyl alcohol and cetearyl alcohol, which have carbon chain length similar to lipophilic portion of surfactant used in emulsion preparation, had showed the best increase in viscosity of O/W emulsions. O/W emulsions prepared with fatty alcohols and fatty acids were pseudo-plastic fluid and they showed shear thinning behaviour like as the common cosmetic emulsions. O/W emulsions prepared with cetyl alcohol, cetearyl alcohol and stearyl alcohol were thixotropic fluids and thixotropy increased with an increase in the concentration of fatty alcohols and fatty acids. Also O/W emulsions prepared with fatty alcohols were more thixotropic than those prepared with fatty acids. For the sake of viscosity increase related to O/W emulsions stability and spreadability enhancement related to payoff, it is thought that fatty alcohols are more useful than fatty acids in the O/W emulsions as the emulsion stabilizer.

• Korean Journal of Materials Research
• /
• v.29 no.4
• /
• pp.221-227
• /
• 2019

This study examines the role of the nano- and micro-particle ratio in dispersion stability and mechanical properties of composite resins for SLA(stereolithography) 3D printing technology. VTES(vinyltriethoxysilane)-coated $ZrO_2$ ceramic particles with different nano- and micro-particle ratios are prepared by a hydrolysis and condensation reaction and then dispersed in commercial photopolymer (High-temp) based on interpenetrating networks(IPNs). The coating characteristics of VTES-coated $ZrO_2$ particles are observed by FE-TEM and FT-IR. The rheological properties of VTES-coated $ZrO_2/High-temp$ composite solution with different particle ratios are investigated by rheometer, and the dispersion properties of the composite solution are confirmed by relaxation NMR and Turbiscan. The mechanical properties of 3D-printed objects are measured by a tensile test and nanoindenter. To investigate the aggregation and dispersion properties of VTES-coated $ZrO_2$ ceramic particles with different particle ratios, we observe the cross-sectional images of 3D printed objects using FE-SEM. The 3D printed objects of the composite solution with nano-particles of 80 % demonstrate improved mechanical characteristics.

• Proceedings of the SCSK Conference
• /
• 2003.09b
• /
• pp.369-369
• /
• 2003

Viscarin is a tradename given to viscosifying carrageenans manufactured by FMC BioPolymer. The suitability of Vis car ins as rheology agents in mild cleansing applications has been investigated. Rheological properties, foam volume and clarity were measured to determine the impact of including 1 % Viscarin on 10% solutions of the following surfactants: acylglutamate, cocoamidopropyl betaine, PEG-80 laurate, sodium lauryl sulphate and sodium lauryol sarcosinate. Viscosity, pseudoplasticity and thixotropy of Viscarin/surfactant solutions varied with surfactant type. In all cases, the addition of Viscarin substantially increased viscosity. For example, at a shear rate of 1 sol, all surfactant solutions had viscosities <0.1 Pa s while viscosities of Viscarin/surfactant solutions ranged from 10 to 60 Pa s. By comparison, a solution of 1 % Viscarin had a viscosity of 0.3 Pa s. Clarity of surfactant solutions decreased in all cases on the addition of Viscarin. However, it was found that by including a mild solubilizing surfactant, such as PEG 40 hydrogenated castor oil, crystal clarity could be maintained in Viscarin/surfactant solutions. Viscarin increased the foam volume of sodium lauryolsarcosinate solutions from 10 ml to 220 ml and had no impact on the foam volume of the other surfactants tested. These results were used to formulate a clear, ultra-mild foaming cleansing gel based on sodium lauryol sarcosinate and Viscarin without the need for a secondary, foam-boasting surfactant. A mild shampoo was also formulated. Both products have excellent skin-feel and are capable of suspending bubbles and solid inclusions.