• 동력기계공학회지
• /
• 제10권2호
• /
• pp.29-35
• /
• 2006

Two-dimensional numerical simulation has been performed to investigate mixed convection heat transfer between inclined parallel plates with bottom-heated and top-cooled uniformly. The ratio of parallel plate length to height is 9.33, Prandtl number is 909(that of silicone oil at 298K) and Rayleigh number is 8600. In the ranges of the Reynolds number Re from 0 to 1.8 and the angle of inclination ${\theta}$ from 0 to 90 degree. The governing equations are discretized using the finite volume method. In this study, the effects of the Reynolds number, the angle of inclination, and the local and mean Nusselt numbers are presented and discussed. It is found that the periodic flow of mixed convection between inclined parallel plates is shown at $0^{\circ}{\leq}\;{\theta}<30^{\circ},\;Re<0.063$, and the flow pattern can be classified into three patterns which depend on Reynolds number and the angle of inclination. The minimum average Nusselt numbers occur at Re=0.05 regardless of the angle of inclination.

• 대한기계학회논문집B
• /
• 제26권7호
• /
• pp.927-936
• /
• 2002

An experimental study has been conducted to investigate the heat/mass transfer characteristics within a film cooling hole of square cross-section for various blowing ratios and Reynolds numbers. The experiments have been performed using a naphthalene sublimation method and the flow field has been analyzed by numerical calculation using a commercial code. A duct flow enters into a film cooling hole in a cross-direction. For the film cooling hole with square cross-section, it is observed that the reattachment of separated flow and the vortices within the hole enhance considerably the heat/mass transfer around the hole entrance region. The heat/mass transfer on the leading edge side of hole exit region increases as the blowing ratios decrease because the main flow induces a secondary vortex. Heat/mass transfer patterns within the square film cooling hole are changed little with the various Reynolds numbers.

• 대한기계학회논문집
• /
• 제8권3호
• /
• pp.185-194
• /
• 1984

본 연구에서는 2차원 정상 층류 유동을 지배하는 극좌표계로 표시된 Navier- Stokes 방정식을 유한해석법으로 전개하여 극좌표계에서의 그 수치계산적 성질을 검토 하고 유한해석법의 적용 좌표계 범위를 확장하는 한편, 2차원 부채꼴 캐비티 유동에 응용하여 공학적 해석도구로서의 그 가능성을 확인하고 아직 연구가 불충분한 부채꼴 캐비티 유동을 고찰하는데 그 목적이 있다.

• 한국가시화정보학회지
• /
• 제4권2호
• /
• pp.44-50
• /
• 2006

A visualization study on the boundary layer and near-wake of an NACA 0012 airfoil was con-ducted in order to investigate the influence of boundary layer behavior on the near-wake at low Reynolds numbers. The present study is investigated at static angles of attack ${\alpha}=0^{\circ},\;3^{\circ},\;6^{\circ}$ and $Re=2.3{\times}10^4,\;3.3{\times}10^4,\;4.8{\times}10^4$ by using a smoke-wire technique. The results of this study show that the laminar boundary layer on the airfoil surface is attached to the surface at ${\alpha}=0^{\circ}$, and that laminar separation of boundary layer on the airfoil surface occurs at ${\alpha}=3^{\circ}$. Furthermore, reattachment of the boundary layer occurs in the case of ${\alpha}=6^{\circ}$. In the current study, the location of the laminar separation point moves upstream as the Reynolds number and the angle of attack increase.

• 한국항공운항학회지
• /
• 제14권4호
• /
• pp.24-30
• /
• 2006

An experimental study was carried out in order to investigate the influence of boundary layer behavior on the near-wake at low Reynolds numbers. An X-type hot-film probe(55R51) was used to measure the near-wake of an NACA 0012 airfoil at static angles of attack ${\alpha}=0^{\circ}$, $3^{\circ}$, and $6^{\circ}$, and the Reynolds numbers Re=2.3${\times}10^4$, 3.3${\times}10^4$, and 4.8${\times}10^4$. The results of the study show that the characteristics of the boundary layer on the airfoil surface have a close relationship with the mean velocity and turbulence intensity profiles of a near-wake. Therefore, the development of the boundary layer, the position of the separation point, and the existence and non-existence of reattachment on the airfoil surface were represented by the differences in mean velocity and turbulence intensity profiles of the near-wake.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.766-771
• /
• 2001

An experimental study was undertaken to investigate the effect of coriolis force for the turbulent flow at low Reynolds numbers in a rotating straight square duct. The study was carried out using a hot-wire anemometer. The flow Reynolds number based on the hydraulic diameter ranged from 4,000 to 18,000 and Rotation number ranged from 0 to 0.196. At Re=9000, developing turbulent flow was calculated for mean velocity and Reynolds stress. Pressure coefficient and energy dissipation spectrum were also calculated.

• Water Engineering Research
• /
• 제3권4호
• /
• pp.247-258
• /
• 2002

This paper presents a non-isotropic turbulence modeling of flows over bedforms. The Reynolds stress model is used for the turbulence closure. In the model, Launder, Reece, and Rodi's model and Hanjalic and Launder's model are employed f3r the pressure strain correlation term and the diffusion term, respectively. The mean flow and turbulence structures are simulated and compared with profiles measured in the experiments. The numerical solutions from two-equation turbulence models are also provided for comparisons. The Reynolds stress model yields the separation length of eddy similar to the other numerical results. Using the developed model, the resistance coefficients are also estimated for the flows at different Froude numbers. Karim's (1999) relationship is used to determine the bedform geometry. It is found that the values of the form drag and the skin friction are very similar to those obtained by the other turbulence models. meaning higher values of the form drag and lower values of the skin friction compared with the empirical formulas.

• 한국전산유체공학회지
• /
• 제18권3호
• /
• pp.34-41
• /
• 2013

We develop a novel immersed boundary (IB) method based on implicit direct forcing scheme for incompressible flows. The proposed IB method is based on an iterative procedure for calculating the direct forcing coupled with the momentum equations in order to satisfy no-slip boundary conditions on IB surfaces. We perform simulations of two-dimensional flows over a circular cylinder for low and moderate Reynolds numbers. The present method shows that the errors for estimated velocities on IB surfaces are significantly reduced even for low Reynolds number with a fairly large time step while the previous methods based on direct forcing failed to provide no-slip boundary conditions on IB surfaces.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권6호
• /
• pp.670-678
• /
• 2002

Fluid flow in a rectangular duct with $90^{\circ}$ mitered elbow is measured by 5W laser doppler velocity meter. The fluid flow is also computed by commercial software of STAR-CD for comparison between measured and computed velocity profiles in the duct. Reynolds numbers for the comparison are 1,608 and 11,751 based on mean velocity and hydraulic diameter of the duct. First, the fluid flow of Reynolds number equal to 1,608 is predicted by assumptions of both laminar and turbulent models. But, even though the Reynolds number is less than 2,300~3,000, the computation by turbulent model is closed to the experimental data than that by laminar model. Second, the computation for Reynolds number of 11,751 by turbulent model also predicted the experimental data satisfactorily.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2390-2395
• /
• 2007

The present research was experimentally performed to analyze the effect of delta-wing vortex generators(DWVG) on the heat transfer of fin surface of the plate fin-oval tube. The local heat transfer coefficient of the fin surface for four kinds of DWVG's arrangement was measured by the naphthalene sublimation technique for Reynolds numbers ranging from 2000 to 3200. The results showed that the heat transfer of the plate fin-oval tube can be significantly enhanced by DWVG for relatively low Reynolds numbers.