• Journal of the Korean Chemical Society
• /
• v.37 no.12
• /
• pp.1035-1046
• /
• 1993

Some iron(III)porphyrin complexes were prepared, and identified by the spectroscopic methods. Elution behavior of iron(III)porphyrin complexes was investigated by reversed-phase HPLC. The optimum conditions for the separation of iron(III)porphyrin complexes were examined with respect to flow rate and mobile phase strength. These complexes were successfully separated on NOVA-PAK $C_{18}$ column using methanol / water(95/5) for $[T_pCF_3PP)Fe(R)]$ and methanol / water (98/2) for $[(P)Fe(C_6F_5)]$ as a mobile phase. It was found that these complexes were largely eluted in an acceptable range of capacity factor value ($0{\leq}logk'{\leq}1$). The dependence of the capacity factor (k') on the volume fraction of water in the binary mobile phase as well as the dependence of k' on the liquid-liquid extraction distribution ratio$(D_c)$ in methanol-water / n-pentadecane extraction system showed a good linearity. It means that the retention of iron(III)porphyrin complexes on NOVA-PAK $C_{18}$ column is largely due to the solvophobic effect. Also, there was a good linear dependence of the capacity factor(k') on the column temperature and enthalpy calculated by van't Hoff plot. From these results, it was confirmed that the retention mechanism of iron(III)porphyrin complexes in reversed-phase liquid chromatography was invariant under the condition of various temperature, and the solvophobic binding process exhibited isoequilibrium behavior.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.1 no.1
• /
• pp.29-35
• /
• 1999

Soil structure and organic matter have been known to strongly affect water flow and solute transport, yet little information is available concerning soil hydraulic properties related to soil physical and chemical properties in the forest site. The purpose of this study was to quantify the spatial variability and spatial correlation of the measured parameter values from the plots established with the rainfall simulator on Japanese larch(Larix leptolepis) dominated site in Kwangju. Kyunggi-Do. Measurement of soil water flux and retention were made with the inherent soil texture, soil structure, and organic matter. The method was based on the observation that when water was applied at a constant rate to the soil surface on each plot. The method was simple to apply and consists of following steps: (i) Wet the soil from a rainfall simulator with several known discharge rates on a relatively leveled soil surface with and without organic matter. (ii) Once the borders of the ponded zone were steady, saturated hydraulic conductivity( $K_{s}$) and the matric flux function(F) was evaluated from a regression of flux vs. the reciprocal of the ponded area. A conductivity of the form $K_{i+}$$_1$ $_{c}$= $K_{i}$( $_{c}$) [1-d /dz] where flux continuity implies. For this, continuity of matric potential at the interface at all times are as follows: $_1$( $Z_{c}$) = $_2$( $Z_{c}$) = $_{c}$ for steady state intake from water ponded on the soil surface. Results of this investigation showed the importance of understanding spatial variability in wide differences of water retention and saturated hydraulic conductivity with respect to pore geometry and organic matter contents which influenced the water flux throughout the soil profile.l profile.ile.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.17 no.5
• /
• pp.368-372
• /
• 1984

This paper deals with a rapid method for determination of ATP and its related compounds in fish and shellfish products using high performance liquid chromatography(HPLC). The HPLC used is a HPLC/ALC-224 equiped with UV-spectrophotometer (254 nm) as detector and integrator (Yanagimoto system-1000). The column used is a stainless steel tubing ($30.0\;cm{\times}3.9\;mm\;i.d.$) packed with ${\mu}-Bon-dapak\;C_{18}$. A mixture of $1\%$ triethylamine-phosphoric acid(pH6.5) was used as an eluent and the flow rate of the eluent was controlled at 2 ml/min. For the separation of ATP and its related compounds, a standard mixture of ATP, ADP, AMP, IMP, inosine and hypoxanthine was subjected to HPLC under the above mentioned conditions. Six peaks were obtained with retention times within 20 min, and elution order were hypoxanthine, IMP, inosine, AMP, ADP and ATP. But 5'-IMP and 5'-GMP fractions were not separated by this method. In generally, IMP content in boiled-dried fish and shellfish products purchased from the market was comparatively higher than that of other nucleotides. Especially, boiled-dried big eye herring marked higher value in IMP content than other boiled-dried ones. Hypoxanthine and inosine were major components of ATP-related compounds in dried products and seasoned-dried ones. And IMP content in seasoned-dried products was higher than that of dried ones. This fact is suggested that a part of IMP in seasoned-dried ones was derived from flavoring matter (MSG, 5'-IMP and 5'-GMP) which is added during the seasoning treatment.

• Journal of Korea Water Resources Association
• /
• v.47 no.5
• /
• pp.483-490
• /
• 2014

The design procedures for a biological reactor and a secondary settling tank (SST) of an activated sludge system are based on the steady state design method (Ekama et al., 1986; WRC, 1984) and the 1-D flux theory design method (Ekama et al., 1997), respectively. This study combined both of the design procedures, to determine the optimum sludge concentration in the reactor and the best design with the lowest cost. The best design of the reactor volume and the SST diameter at the optimum sludge concentration were specified with varying wastewater and sludge characteristics, temperature, sludge retention time (SRT) and peak flow rate. The effects of the influent wastewater characteristics, such as substrate concentration and unbiodegradable particulate fraction, were found to be considerable, but the effect of unbiodegradable soluble fraction was to be negligible. The effects of sludge settling characteristics, were also significant. SRT, as an operating parameter, was found to be an important factor for determining the optimum sludge concentration. However, the effect of temperature was found to be small. Furthermore, for designing a large scale wastewater treatment plant, the number of reactors or SSTs could be estimated, by dividing the total reactor volume or SST area. The new combined design procedure, proposed in this research, will be able to allow engineers to provide the best design of an activated sludge system with the lowest cost.

• Korean Chemical Engineering Research
• /
• v.56 no.5
• /
• pp.718-724
• /
• 2018

In this study, the $Ni_{0.9}Co_{0.05}Ti_{0.05}(OH)_2$ precursor was prepared by the concentration gradient co-precipitation method. In order to overcome the structural change due to oxygen desorption in the cathode active material with high nickel content, the physical and electrochemical analysis of the cathode active material according to the calcination temperature were investigated. Physical properties of $Li_{1.05}Ni_{0.9}Co_{0.05}Ti_{0.05}O_2$ were analyzed by FE-SEM, XRD and TGA. The electrochemical performance of the coin cell using a cathode active material and $LiPF_6$(EC:EMC=1:2 vol%) electrolyte was evaluated by the initial charge/discharge efficiency, cycle retention, and rate capabilities. As a result, the initial capacity and initial efficiency of cathode materials were excellent with 244.5~247.9 mAh/g and 84.2~85.8% at the calcination temperature range of $750{\sim}760^{\circ}C$. Also, the capacity retention exhibited high stability of 97.8~99.1% after 50cycles.

• Applied Biological Chemistry
• /
• v.50 no.1
• /
• pp.18-22
• /
• 2007

The optimum production condition for the antibiotic from Bacillus thuringiensis BK4 was determined, and the suppression rate of Fusarium-wilt by the butanol-extracted antibiotic was verified by employing tomatoes in vitro and in vivo pot tests. Cell growth and antifungal activity were the best when 0.5% xylose and 0.2% peptone No.3 were given as carbon and nitrogen sources, respectively, in the presence of 5mM $CaCl_2$. The partially purified antibiotic successfully prevented Fusarium oxysporum pathogen in pot experiments. When the pots were treated with both live cells and the partially purified antibiotic, an additive-effect was seen in the suppression of Fusarium-wilt, but synergistic effect was not detected. The antibiotic, denoted BK4, purified by Sephadex LH-20 column chromatography was eluted with a single peak at a retention time of 38 min. on prep-HPLC; Minimum inhibition concentration of the homogenous antibiotic was determined to be 50${\mu}$g/ml.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.34 no.1 s.114
• /
• pp.21-36
• /
• 2006

This study was undertaken to analyze the effects of pavement thermal properties and water retention characteristics on the surface temperature of the gray permeable cement concrete pavement during the summer. Following is a summary of major results. 1) The hourly surface temperature of pavement could be well predicted with a heat transfer model program that incorporated the input data of major meteorological variables including solar radiation, atmospheric temperature, dew point, wind velocity, cloudiness and the evaporation rate of the pavements predicted by the time domain reflectometry (TDR) method. 2) When the albedo was changed to 0.5 from an arbitrary starting condition of 0.3, holding other variables constant, the peak surface temperature of the pavement dropped by 11.5%. When heat capacity was changed to $2.5\;kJm^{-3}K^{-1}\;from\;1.5\;kJm^{-3}K^{-1}$, surface temperature dropped by 8.0%. When daily evaporation was changed to 1 mm from 2 mm, temperature dropped by 5.7%. When heat conductivity was changed to $2.5\;Wm^{-1}K^{-1}\;from\;1.5\;Wm^{-1}K^{-1}$, the peak surface temperature of the pavement fell by 1.2%. The peak pavement surface temperature under the arbitrary basic condition was $24.46^{\circ}C$ (12 a.m.). 3) It accordingly became evident that the pavement surface temperature can be most effectively lowered by using materials with a high albedo, a high heat capacity or a high evaporation at the pavement surface. The glare situation, however, is intensified by raising of the albedo, moreover if reflected light is absorbed into surrounding physical masses, it is changed into heat. It accordingly became evident that raising the heat capacity and the evaporative capacity may be the moot acceptable measures to improve the thermal characteristics of the pavement. 4) The sensitivity of the surface temperature to major meteorological variables was as follows. When the daily average temperature changed to $0^{\circ}C\;from\;15^{\circ}C$, holding all other variables constant, the peak surface temperature of the pavement decreased by 56.1 %. When the global solar radiation changed to $200\;Wm^{-2}\;from\;600\;Wm^{-2}$, the temperature of the pavement decreased by 23.4%. When the wind velocity changed to $8\;ms^{-1}\;from\;4\;ms^{-1}$, the temperature decreased by 1.4%. When the cloudiness level changed to 1.0 from 0.5, the peak surface temperature decreased by 0.7%. The peak pavement surface temperature under the arbitrary basic conditions was $24.46^{\circ}C$ (12 a.m.)

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.6
• /
• pp.537-545
• /
• 2009

The objective of this study was to investigate potential usage of environmentally friendly building materials, liquid mortar and dry cement mortar mixed with charcoal, based on the test of their physical and chemical properties. From the test results of physical and chemical properties of the liquid mortar mixed with charcoal, liquid mortar containing over 20% of charcoal, the consistency viscosity and the non-volatile content met a standard requirement. Drying time was delayed with increase in charcoal contents in the liquid mortar, however they were fully cured within 60 minutes in all treated levels. Other properties were acceptable at standard requirement. From the results, it was found that the proper charcoal addition level to the liquid mortar was 25%. In the results on dry cement, it was found that samples containing 5% of charcoal showed the maximum compressive strength, whereas samples containing over 20% of charcoal did not reach the minimum requirement of KS standard. Water retention ability constantly increased as the charcoal ratio increased. The conventional dry cement mortar adsorbed 59.5% of it, in the test of adsorption rate on ammonia gas, whereas cement mortar containing 10% of charcoal showed 71.6% of ammonia gas adsorption.

• Journal of Preventive Medicine and Public Health
• /
• v.40 no.2
• /
• pp.155-161
• /
• 2007

Objectives : Bisphenol A diglycidyl ether (BADGE) is the major component in commercial liquid epoxy resins, which are manufactured by co-reacting bisphenol A with epichlorohydrin. This study was performed to show the developmental effects of prenatal and postnatal exposures to BADGE in male rat offspring. Methods : Mated female rats were divided into four groups, each containing 12 rats. The dosing solutions were prepared by thoroughly mixing BADGE in corn oil at the 0, 375, 1500 and 3000 mg/kg/day concentrations. Mated females were dosed once daily by oral gavage on gestation day (GD) 6 - 20 and postnatal day (PND) 0 - 21. Pregnant female dams were observed general symptoms and body weight. Also, male pups were observed the general symptoms, body weight, developmental parameters (e.g. anogenital distance, pina detachment, incisor eruption, nipple retention, eye opening, testis descent), organ pathologic changes and hormone levels of plasma. Results : Pregnant rats treated with BADGE died at a rate of about 70% in the 1500 mg/kg/day group and all rats treated with 3000 mg/kg/day died. Body weight, for male pups treated with doses of 375 mg/kg/day, was significantly lower than in the control group at PND 42, 56, and 63 (p<0.05). Evaluation of body characteristics including; separation of auricle, eruption of incisor, separation of eyelid, nipple retention, descent of testis, and separation of the prepuce in the BADGE treated group showed no difference in comparisons with the control group. AGD and adjusted AGD (mm/kg) for general developmental items in BADGE 375 mg/kg/day treated pups tended to be longer than in controls, however, these differences were not statistically significant. Relative weights of adrenal gland, lung (p<0.05), brain, epididymis, prostate, and testis (p<0.01) were heavier than in control in measures at PND 9 weeks. There were no significant changes in comparisons of histological findings of these organs. Loss of spermatids was observed in the seminiferous tubule at PND 9 weeks, but no weight changes were observed. The plasma estrogen levels were similar in the control and treatment groups at PND 3, 6 and 9 weeks. The plasma testosterone levels in the control group tended to increase with age. However, in the BADGE 375 mg/kg/day treated male pups it did not tend to increase. Conclusions : These findings suggest that BADGE is a chemical that has developmental effects consistent with it being an endocrine disruptor.

• Korean Chemical Engineering Research
• /
• v.57 no.6
• /
• pp.832-840
• /
• 2019

To improve the electrochemical performances of the cathode materials, boron-doped $LiNi_{0.90}Co_{0.05}Ti_{0.05}O_2$ were synthesized by using concentration gradient precursor. The characteristics of the prepared cathode materials were analyzed by XRD, SEM, EDS, PSA, ICP-OES and electrical conductivity measurement. The electrochemical performances were investigated by initial charge/discharge capacity, cycle stability, C-rate, cyclic voltammetry and electrochemical impedance spectroscopy. The cathode material with 0.5 mol% boron exhibited a capacity of 187 mAh/g (0.5 C) in a voltage range of 2.7~4.3 V(vs. $Li/Li^+$), and an capacity retention of 94.7% after 50 cycles. In the relatively high voltage range of 2.7~4.5 V(vs. $Li/Li^+$), it showed a high capacity of 200 mAh/g and capacity retention of 80.5% after 50 cycles.