• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.1
• /
• pp.161-182
• /
• 2018

We carried out a series of linear cutting machine tests to assess the cutting performance of a pick cutter in sedimentary rock. The specimens were Linyi sandstone from China and Concrete (rock-like material, conglomerate). Using the small scaled LCM system, we estimated the cutter force and specific energy under different cutting conditions. The cutter forces (cutting and normal) increased with penetration depth and cutter spacing in two rock types, and it was affected by the strength of specimens. On the other hand, the ratio of the peak cutter force to the mean cutter force was influenced by cutting characteristic and composition of rock rather than rock strength. The cutting coefficient was affected by the friction characteristic between rock and pick cutter rather than the cutting conditions. Therefore, the optimal cutting angle can be determined by considering of cutting coefficient and resultant force of pick cutter. The optimum cutting condition was determined from the relationship between the specific energy and cutting condition. For two specimens, the optimum s/p ratio was found to be two to four, and the specific energy decreased with the penetration depth. The result from this study can be used as background database to understand the cutting mechanism of a pick cutter, also it can be used to design for the mechanical excavator.

• Journal of the korean Society of Automotive Engineers
• /
• v.8 no.3
• /
• pp.28-36
• /
• 1986

This study was investigated the feasibility of AE application on in-process detection of tool fracture and chipping. Carbon steel SM45C workpiece with longitudinal slots was turned interruptedly on a lathe. AE RMS signal at tool fracture was observed and also the tangential force and the feed observed at the time of tool fracture, the levels of tangential force and the feed force at the time of fracture decrease considerably. In chipping, high level AE signal was observed but there were no changes of cutting force. Peak AE RMS squared is proportional to the area of tool fracture and resultant force. Fracture model of tool fracture is proposed as $V_{p}$ = $C_{1}$ $E_{1}$F(.DELTA. A)$_{0.5}$ and peak AE RMS shows strong correlation with the fracture parameter F(.DELTA.A)$^{0.5}$.

• Journal of Ocean Engineering and Technology
• /
• v.8 no.1
• /
• pp.131-143
• /
• 1994

The BTA(boring and trepanning association) deep hole machining has an increasing demands because of its wide applications and its good productivity. The main feature of the BTA tools is that the tool cutting edges are unsymmetrically located on the boring head. This provides a stabilizing cutting force resultant necessary for self guidance of the boring head. The BTA tools are capable of machining for having a large length to diameter ratio in single pass. A study of the accuracy and surface finish of holes produced would reveal quite useful information regarding the process. This study deals with the experimental results obtained during BTA machining on SM55C, SM45C steel under differnt machining conditions.

• Korean Journal of Applied Biomechanics
• /
• v.25 no.3
• /
• pp.363-370
• /
• 2015

Objective : The purpose of this study was to give the basic data for the cutting movement with the various angels on the poly urethane. Method : Ten healthy men voluntarily participated in this study. A three-dimensional motion analysis system (VICON) and force plates were used to analyze the movements of the joints for the lower extremities. For the statistical analysis the IBM SPSS 21.0 was used to perform repeated measured ANOVA and post-hoc comparison result was used to perform the Scheffe and the level of significance was set up at ${\alpha}=.05$. Results : There were significant differences for the time required for the increasing angles of the cutting movement(p<.05). In addition, there were significant differences for the maximum dorsiflexion, plantarflexion of ankle joint, maximum flexion of knee joint and hip joint with the increasing the angles of cutting movement(p<.05). Also, there were significant differences for the maximum adduction and abduction angle of the hip joint with the increasing of the angles of cutting movement. There was signigicant difference for the resultant utilized coefficient of friction(RuCOF) for the increasing angles of cutting movement(p<.05). Conclusion : There was a pattern to increase the coefficient friction with the angle of cutting direction. Also, it would be possible to use the poly urethane for the outdoor floor with the results of this study.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.1
• /
• pp.71-79
• /
• 2004

The deformed layers generated in face milling works were comparatively investigated to type 316L and nitrogen(N)-added type 316LN stainless steels. In order to characterize mechanical properties between type 316L and type 316LN, high-temperature tensile tests were conducted with different temperatures: R.T to $700^{\circ}C$. The cutting forces of three components, Fx, Fy and Fz were measured using a tool dynamometer through the face milling cutting tests. The deformed layers were measured by micro-hardness tests along deformed layers. The results of mechanical properties showed that type 316LN was superior to type 316L. The deformed layers of two steels were generated in the 1501m-3001m ranges, and type 316L was higher than type 316LN. The reason for this is due to the high strength properties by nitrogen effect. It was found that deformed structures were well observed for type 316L, but were minutely observed for type 316LN in this cutting conditions.

• Journal of Advanced Marine Engineering and Technology
• /
• v.18 no.2
• /
• pp.64-74
• /
• 1994

The gundrill is capable of machining for having large length to diameter ratio in single pass. The techniques of gundrill and gun boring began developing in the late 18th century with the need for more accurate bores in rifle, cannon, machinery part and marine part etc. The main feature of the gun drilling provides a stabilizing cutting force resultant necessary for self guidance of the drill head. A study of the accuracy and surface finish of holes produced would reveal quite useful information regarding the process. The thesis deals with the experimental results obtained during gun drilling on marine part materials for different machining conditions.