• 대한조선학회논문집
• /
• 제55권4호
• /
• pp.321-329
• /
• 2018

Resonance phenomena occurs at large vertical pump which is operating to cool down the hot steam using sea water in the power plant. To avoid the resonance, the natural frequency needs to be isolated about 20% from motor operating speed. Yet, excessive vibration occurs especially at low tide. At first, natural frequency of the whole pump system and each part is calculated using ANSYS. As it is revealed in the previous journal papers that only circular pipe part is related to resonance, the FSI technique is applied for free vibration analysis. The natural frequency is reduced to 60% (compared to that) of the frequency measured in air as it is similar to other published results. And the frequency obtained by finite element analysis is almost same to that obtained from modal test. Based on the accurate finite element model and analysis, design change is tried to avoid the resonance by changing the thickness of pipe and base supporting plate. In stead of doing optimization process, design sensitivity is computed and used to find such designs to avoid resonance.

• 한국소음진동공학회논문집
• /
• 제27권2호
• /
• pp.148-154
• /
• 2017

This paper discussed design for resonance avoidance of sensor plates of loose-parts monitoring systems (LPMS) in nuclear power plants (NPP). An LPMS monitors impact of loose parts in primary loop of NPP by using accelerometers, which is mounted on sensor plates. Resonance of the plates may cause false alarms at frequencies over 10 kHz, which can be misunderstood as impact signals of loose parts with small mass and cause unnecessary response of NPP operators. Modal analysis was carried out for the existing sensor plate and design parameters affecting natural frequencies were chosen. Frequency response functions of plates were analyzed by changing the parameters and the optimized plate design for avoiding resonance was determined. Experiments was carried out for the plate specimen with improved design and verified the proposed approach and design.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2013년도 특별논문집
• /
• pp.55-59
• /
• 2013

Transverse vibrations of ship's aft end and deckhouse among the various modes of hull structures are induced mainly by transverse exciting forces and moments of main engine such as ${\times}$ and h-moment. Avoidance of resonance should be made in a intial design stage in case there is a prediction for resonance between main engine and transverse modes of deckhouse. This study shows a case of change in type of main engine from 12 cylinders to 10 without modification of hull structures in engine room requested by a shipowner of 8,600 TEU class container carrier and proposes a guide to the effective ways of structural arrangement for avoiding resonance between transverse exciting force and surrounding structures of main engine in engine room through case studies.

• 한국공작기계학회논문집
• /
• 제17권6호
• /
• pp.35-42
• /
• 2008

Most of tasks for vertical surface work in shipyard have been accomplished by human workers. However, such manual work often causes injury to workers, also the production cost becomes high due to increasing individual wage. To cope with the circumstance, shipbuilding companies try to introduce wall-climbing robots for carrying out such kind of tasks. In designing a wall-climbing robot, it is essential to minimize its own weight to improve the performance such as moving speed and power saving. For such purpose. this study proposes a method of optimal design for a wall-climbing robot using a genetic algorithm with multi-objective function. Specifically, the thickness of the robot base is minimized to reduce the weight while maintaining the allowable strength and avoiding the resonance frequencies. The proposed method is applied to the design of a wall-climbing robot, and the result shows that the method is useful at an early design stage.

• 풍력에너지저널
• /
• 제9권4호
• /
• pp.57-64
• /
• 2018

To maximize power generation and reduce the construction cost of a commercial utility-grade wind turbine, the size of the wind turbine should be large. The initial design of the 12 MW University of Ulsan(UOU) Floating Offshore Wind Turbine(FOWT) was carried out based on the 5 MW National Renewable Energy Laboratory(NREL) offshore wind turbine model. The existing 5 MW NREL offshore wind turbines have been expanded to 12 MW UOU FOWT using the geometric law of similarity and then redesigned for each factor. The resonance of the tower is the most important dynamic responses of a wind turbine, and it should be designed by avoiding resonance due to cyclic load during turbine operations. The natural frequency of the tower needs to avoid being within the frequency range corresponding to the rotational speed of the blades, 1P, and the blade passing frequency, 3P. To avoid resonance, vibration can be reduced by modifying the stiffness or mass. The direct expansion of the 5 MW wind turbine support structure caused a resonance problem with the tower of the 12 MW FOWT and the tower length and diameter was adjusted to avoid a match of the first natural frequency and 3P excitation of the tower.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.902-905
• /
• 2004

Recently, the composite materials are widely used for manufacturing the helicopter rotor blades. furthermore, composites show great potential on the design of rotor blades due to the advantages of strength, durability and weight of the materials. To keep with this advantages, it is necessary to calculate natural frequencies of a rotating blades for avoiding resonance. In this paper, the structural design process of airfoil cross section is introduced, and natural frequencies of composite rotor blades with variable rpm we investigated.

• 한국소음진동공학회논문집
• /
• 제26권5호
• /
• pp.584-593
• /
• 2016

In this study, an improvement design method for reducing the vibration of fenders equipped in a tractor is proposed through the establishment of a finite element model and the topology optimization. As the original shapes of the parts cannot be altered, an improved design model was derived in which a stiffener was attached to the border of parts. Thus, the first resonance frequency was increased by approximately 16 Hz, which was confirmed to be the frequency interval for avoiding the idle and operating frequency of the engine. Finally the improved design model was applied to confirm the effect of vibration reduction. Therefore, it can be concluded that the improved design model of the tractor fender is effective at reducing vibrations of the tractor fender.

• 한국산학기술학회논문지
• /
• 제20권8호
• /
• pp.279-285
• /
• 2019

다양한 형태의 선체 진동 중, 선체 선미 및 거주구의 횡방향 진동은 대부분 주기관의 횡기진력으로부터 유발되는데, 주기관과 연결된 주변 구조물과의 공진이 발생 할 수 있으므로 공진회피 설계가 반드시 필요하다. 공진 회피를 위한 가진 주파수는 주기관 및 프로펠러 사양으로부터 추정 가능하나, 기관실 주변 구조물의 고유 진동수는 형상의 다양성 등에 의해 추정이 쉽지 않고 경험을 위주로 한 방진 설계가 수행되고 있는 현실이며, 이로 인해 시운전 중에 발생하는 진동 문제는 공정지연, 현장 인력의 과다 투입 및 설계의 반복 수행 등 많은 문제점이 발생하고 있다. 본 연구에서는8,600TEU급 컨테이너선을 대상으로 유연한 설계를 위해 선체 구조배치의 변경 없이 주기관만 12기통에서 10기통으로 변경하는 경우에 대해 주기관 횡진동에 의한 공진 문제를 다루었다. 연구 결과로서, 주기관 횡기진력과 기관실 주변 구조와의 공진 회피를 위한 효율적인 구조보강 설계지침을 제시하였으며, 설계 현장의 실제적인 방진설계 지침으로 활용이 기대된다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1996년도 추계학술대회논문집; 한국과학기술회관, 8 Nov. 1996
• /
• pp.313-318
• /
• 1996

In this paper, a parametric study of the unbalance response and the stability is carried out to show the influence of seal parameters on the response of rotor. The seal parameters optimized are the seal clearance and the seal length. The minimum quantity of a Q factor in the critical speed and the maximum quantity of a logarithmic decreement in the operating speed, avoiding the reign of resonance, are the objective function. This paper describes a new approach to find a seal parameter of rotor system. The optimization method is used genetic algorithms, which are search algorithms based on the mechanics of natural selection and natural genetics. The results show the capability of this method and indicate that an optimal design of seals can improve the unbalance and the stability of rotor.

• Coupled systems mechanics
• /
• 제11권6호
• /
• pp.525-542
• /
• 2022

In this work we present an advanced approach to the design of small wind turbine support steel structures. To this end we use an improved version of previously developed geometrically exact beam models. Namely, three different geometrically exact beam models are used, the first two are the Reissner and the Kirchhoff beam models implementing bi-linear hardening response and the third is the Reissner beam capable of also representing connections response. All models were validated in our previous research for a static response, and in this work they are extended to dynamic response. With these advanced models, we can perform analysis of four practical solutions for the installation of small wind turbines in new or existing buildings including effects of elastoplastic response to vibration problems. The numerical simulations confirm the robustness of numerical models in analyzing vibration problems and the crucial effects of elastoplastic response in avoiding resonance phenomena.