• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.601-606
• /
• 2004

Vibration spectrums of the test loop according to flow conditions were analyzed in order to identify the sources of vibration at peak frequencies. While a flow condition of the sweep test was changed by varying pump rotational speed from 450 rpm to 1500 rpm by the step 150 rpm, midspan acceleration of the test section in width-direction and dynamic pressure perturbation in the test section were measured. Other sources of vibration due to the flow structure interactions, such as acoustic resonance, blade pulsing frequency and bellows wrinkles, were investigated. Pressure perturbation in the section and acoustic resonance due to branch pipe give major effects to the vibration of the test section in high frequency range of 1.5 kHz to 2.8 kHz.

• Journal of Power Electronics
• /
• 제12권4호
• /
• pp.559-566
• /
• 2012

A new design method for the LCL filters of three-phase voltage source PWM rectifiers is presented in this paper. Based on the single-phase harmonic equivalent model, the harmonic voltage of the rectifier side is calculated to design the LCL filter parameters by an iterative algorithm, in which the resonance frequency $f_{res}$ and the ratio r between the grid-side inductance and the rectifier-side inductance are selected as known constants. The design criteria and process are introduced and the influence on the design result by the value of the resonance frequency $f_{res}$, ratio r is analyzed. Finally an example (600V, 500kW) is tested by simulation and experiment to verify the validity of the new design method.

• 전자공학회논문지A
• /
• 제33A권7호
• /
• pp.111-120
• /
• 1996

In this paper, we proposed an inductance loaded small type open-loop travelling wave antenna model for the suitable VHF/UHF frequency bands moisture measurement systems and analyzed its operating characteristics by galerkin's solution method. This antenna model enables to change the oeprating rsonance frequency from the frequency range 150 Mhz to 1.0 Ghz without changing the antenna design dimensions by only varing the load inductance values and it showed the similar operating charcteristics and narrowband resonance characteristics at each resonance frequencies. Also this model showed the uniformly distriubte dpower radiation characteristics above the loop axis and it can effectively suppress the spurious radiations from its narrowband resonance characteristics.

• Journal of Magnetics
• /
• 제18권2호
• /
• pp.155-158
• /
• 2013

FeCoB films were being prepared on a Ru underlayer by using the oblique incidence of sputtered and back-scattered particles which have a high in-plane magnetic anisotropy field $H_k$ above 400 Oe. It is suitable to attain such deposition condition when facing targets sputtering system. The in-plane X-ray diffraction analysis clarified that there is anisotropic residual stress which is the origin of the high in-plane magnetic anisotropy. The directional crystalline alignment and inclination of crystallite growth were also observed. Such anisotropic crystalline structures may affect the anisotropic residual stress in the films. The B content of 5.6 at.% was appropriate to induce such anisotropic residual stress and $H_k$ of 410 Oe in this experiment. The film with B content of 6 at.% possessed large saturation magnetization of 22 kG and high $H_k$ of 500 Oe. The film exhibited high ferromagnetic resonance frequency of 9.2 GHz.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2005년도 동계학술발표대회 논문집
• /
• pp.335-340
• /
• 2005

Nonlinear and forced oscillations of supported viscous droplet were focused in the present study. The droplet has a free contact line with solid plate and inviscid fluid. Natural frequencies of a pendant droplet have been investigated experimentally by imposing the acoustic wave while the frequency is being increased at a fixed amplitude. The evaporation was observed at atmosphere pressure. The droplet was recorded throughout the entire evaporation process and transient variations of the volume was measured. The evaporation process of oscillating droplet with thermofoil has been also observed to investigate analyzing the resonance effect on the thermal characteristics of droplet. It is found that a pendant droplet shows the resonant behaviors at each mode similar to the theoretical analysis. During imposing the acoustic wave, the pendant droplet makes a rotating motion in its longitudinal axis which is a new shape oscillation mode. The evaporation rate of a pendant droplet at resonant frequency is significantly enhanced.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.429-434
• /
• 2004

Vibration response of the tower structure of a 750kW wind turbine generator is investigated by measurement and analysis. Acceleration response of the tower under various operation condition is monitored in real time by vibration monitoring system using LabVIEW. Resonance state of the tower structure is diagnosed in the operating speed range. To predict the tower resonance frequency, tower is modeled as an equivalent beam with a lumped mass and Rayleigh energy method is applied. Calculated tower bending frequency is in good agreement with the measured value and the result shows that the simplified model can be used in the design stage of the wind turbine tower.

• 지질공학
• /
• 제31권2호
• /
• pp.211-222
• /
• 2021

포항지진은 2017년 규모 5.4의 포항시 북구 북쪽 7.5 km 부근에서 발생하였다. 지진피해가 크게 발생한 경상북도 포항 북구 지역의 상시미동의 특성을 알아보기 위하여 총 39 지점에 상시미동 자료를 취득하여 수평 대 수직 스펙트럼 비율(Horizontal to Vertical Spectral Ratios, HVSR) 분석연구를 실시하였다. 상시미동은 지역에 따라 각각 다르므로 상시미동을 조사해 그 지역의 공명주파수를 취득한다. 층후 분석을 위해서는 기반암까지의 전단파 속도(Vs) 구조 및 특성을 분석하여 공명주파수를 인근의 시추자료와 대비하여 수평 대 수직 스펙트럼 비율(Horizontal to Vertical Spectral Ratios, HVSR) 분석기법이 일치하는지 비교하였다. 충적층의 공명주파수 1.3 ± 0.07 Hz, 연일층군의 공명주파수 0.69 ± 0.22 Hz로 F₀ = V_s/4H를 이용하여 층후를 구하면 충적층은 26~30 m, 연일층군은 170~250 m로 인근 시추자료와 비교하여 대체로 일치한 것으로 분석하였다.

• 한국소음진동공학회논문집
• /
• 제21권3호
• /
• pp.258-263
• /
• 2011

The direction of the cutting tool plays a critical role in elliptical vibration cutting(EVC) where the cutting tool cuts workpiece in a trochoidal motion. In this study, EVC cutting device was developed using two parallel piezoelectric materials and it was observed that the rotation direction of the tool reverses as the EVC device undergoes resonance at which either flexural(cutting direction) or longitudinal( thrust direction) mode shapes occurs. To analytically explain reversal of the rotation direction, kinematic motion analysis of the tool was modified to incorporate amplification of the vibration amplitude and phase introduced by resonance. It successfully demonstrated, through Matlab simulation, reversal of the rotation direction of the cutting tool as the excitation frequency increases beyond resonance frequencies at which either flexural or longitudinal vibration occurs.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.638-641
• /
• 2002

This paper presents design and construct of flat type step-down piezoelectric transformer for the application to AC-adapters. This piezoelectric transformer operated in resonance vibration mode. In this paper, Finite element method(FEM) was used for analysis piezoelectric transformers. Vibration mode and electric field of piezoelectric transformer at resonance frequency were simulated. Using this simulation, we manufactured flat type piezoelecric transformer and measured its output characteristics. As results, output power was linearly increased by increasing input power at resonance frequency. And it was found that the transformer exhibited an output power of 11.4[W] at 60[V] input voltage. From these results, we expect that this piezoelecric transformer can be applied to AC adapters.

• 한국정밀공학회지
• /
• 제28권8호
• /
• pp.951-958
• /
• 2011

In this paper, the purpose is to investigate the vibration characteristics and the design of resonance avoidance of the unmanned helicopter master. Based on the Euler-Bernoulli beam theory for helicopter master, the equation of motion is derived by using extended Hamilton's principle. It was studied about the natural frequency of helicopter master as the design variances(tip mass, length and diameter of master). Also, it was compared the theoretical results for natural frequency with the results of FE analysis. The results of this study showed the vibration characteristics of helicopter master for the design of resonance avoidance.