• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.5 no.4
• /
• pp.191-197
• /
• 2012

In this paper, method using electric braking from stop area to high-speed area was presented in order to improve air-brake. And electric braking method can be improved environmental problems, efficiency, economy, etc.. Method for electrical complete braking are two ways that method of inserting series resistance between the motor and the inverter, and method of inverter output voltage increase. In this paper, use series resistance insert method because economical and easy to apply. In addition, Series resistor is used short circuit method for reduce the power loss. In improved efficiency and the laboratory environment for secure braking, resistance insert method and inverter output voltage increase method showed same characteristics in all areas.

• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.4
• /
• pp.58-65
• /
• 1992

In this paper, wave resistance for a submerged body is calculated by a higher order panel method. The Neumann-Kelvin problem is solved by the source or normal dipole distribution method. The body surface is represented by a bicubic B-spline and the singularity strengths are approximated by a bilinear form. The results calculated by the higher order panel method are compared with those by the lowest order panel method developed by Hess & Smith. The convergence rate of the higher order panel method is much better than the lowest order panel method. But the wave resistance calculated by the higher order panel method still shows discrepancy with an analytic solution at low Froude number like that by the lowest order panel method.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.5 no.3
• /
• pp.127-137
• /
• 2012

In this paper, method using electric braking from stop area to high-speed area was presented in order to improve air-brake. And electric braking method can be improved environmental problems, efficiency, economy, etc. Method for electrical complete braking are two ways that method of inserting series resistance between the motor and the inverter, and method of inverter output voltage increase. In this paper, use series resistance insert method because economical and easy to apply. In addition, Series resistor is used short circuit method for reduce the power loss. In improved efficiency and the laboratory environment for secure braking, resistance insert method and inverter output voltage increase method showed same characteristics in all areas.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.322-325
• /
• 2007

Dent resistance is an important characteristic to avoid damage on automotive outer panels. From a practical point of view, dents can be caused in a number of ways. Considering doors as an example, denting can occur from stone impacts or from the careless opening of an adjacently parked vehicle door. Denting can occur where the door surface is smooth and may not have sufficient curvature to resist dent. These exterior body parts are designed to improve dent resistance using a combination of work hardening and bake hardening. In brief, dent is affected by the shape of the parts and the material properties such as yield strength, strain and thickness. In this work, forming of door outer panel is investigated by Taguchi method. Main parameters are yield strength, thickness, blank size, blank holding force and so on. For the given value of design parameters, forming analysis of the thirty six cases are carried out according to L18 orthogonal array. After comparing the performance by simple conversion of simulation results into dent resistance, the final suggestion of the forming parameters is verified for the best improvement of dent resistance.

• Korean Journal of Materials Research
• /
• v.24 no.10
• /
• pp.526-531
• /
• 2014

Thermal shock resistance property has recently been considered to be one of the most important basic properties, in the same way that the transverse-rupture property is important for sintered hard materials such as ceramics, cemented carbides, and cermets. Attempts were made to evaluate the thermal shock resistance property of 10 vol% TaC added Ti(C,N)-Ni cermets using the infrared radiation heating method. The method uses a thin circular disk that is heated by infrared rays in the central area with a constant heat flux. The technique makes it possible to evaluate the thermal shock strength (Tss) and thermal shock fracture toughness (Tsf) directly from the electric powder charge and the time of fracture, despite the fact that Tss and Tsf consist of the thermal properties of the material tested. Tsf can be measured for a specimen with an edge notch, while Tss cannot be measured for specimens without such a notch. It was thought, however, that Tsf might depend on the radius of curvature of the edge notch. Using the Tsf data, Tss was calculated using a consideration of the stress concentration. The thermal shock resistance property of 10 vol% TaC added Ti(C,N)-Ni cermet increased with increases in the content of nitrogen and Ni. As a result, it was considered that Tss could be applied to an evaluation of the thermal shock resistance of cermets.

• Geotechnical Engineering
• /
• v.12 no.6
• /
• pp.21-36
• /
• 1996

The stress transfer mechanism between soil and grid reinforcements involves two basic mechanism : frictional soil resistance and passive soil resistance. However the mechanism of the passive soil resistance is very complex to understand. To study the failure mechanism of ribbed reinforcement, the direct shear tests which are dominated by passive soil resistance are analyzed by using the finite element method. The finite element method is used to examine the effects of ribs on this passive soil resistance development and the met hanism of failure. The calculated behavior of the ribbed reinforcement is compared with the measured behavi or. Comparisons between the measured and the simulated strain pat terns, failure modes and load displacement relationship are presented. The behavior of the ribbed reinforcements in a cohesive soil is predicted on the basis of a good agreement between the measured and the Predicted behavior of the Ottawa sand.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.569-576
• /
• 2003

Based on the equivalent uniform stress concept Presented by Seed and Idriss, sinusoidal cyclic loads which simplified earthquake loads have been applied in evaluating the liquefaction resistance strength experimentally. However, the liquefaction resistance strength of soil based on the equivalent uniform stress concept can not exactly reflect the dynamic characteristics of the irregular earthquake motion. The liquefaction assessment method which was invented by using the equivalent uniform stress concept is suitable for the severe earthquake region such as Japan or USA, so the proper method to Korea is needed. In this study, estimation of the resistance to liquefaction was conducted by applying real earthquake loading to the cyclic triaxial test. From the test results, the characteristics of the fine sand under moderate earthquake were analyzed and compared with the results under strong earthquakes. Typically real earthquake loads used in this study are divided into two types - impact type and vibration type. Furthermore, results of the liquefaction resistance strength based on the equivalent uniform stress concept and tile concept using real earthquake loading were compared.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.10 s.181
• /
• pp.2581-2588
• /
• 2000

In previous studies, the dynamic resistance, which was calculated by the process variables measured at the electrode of the welding machine, and the electrode displacement were used for quality exa mination. However, in-process usage of such systems is not effective in systems that include a welding gun attached to a robot. In order to overcome such problems, we obtained and used the process variables from the welding machine timer. This would allow us to estimate real time in -process weld quality. For quality estimation, the features were extracted as factors from the primary dynamic resistance patterns, which were measured in t he welding machine timer. The relationship between the indexes and nugget size of the welds was observed through the regression analysis. Using the analyzed factors, a regression model that could estimate nugget diameter was developed. Two regression equations of the model were suggested depending on the factors, and it was showed that the model developed by stepwise method was effective one for weld quality estimation. The developed estimation model was in good linearity with the nugget diameter obtained through the experimentation.

• Transactions of Materials Processing
• /
• v.16 no.4 s.94
• /
• pp.254-259
• /
• 2007

Dent resistance is an important characteristic to avoid damage on automotive outer panels. From a practical point of view, dents can be caused in a number of ways. Considering doors as an example, denting can occur from stone impacts or from the careless opening of an adjacently parked vehicle door. Denting can occur where the door surface is smooth and may not have sufficient curvature to resist dent. These exterior body parts are designed to improve dent resistance using a combination of work hardening and bake hardening. In brief, dent is affected by the shape of the parts and the material properties such as yield strength, strain and thickness. In this work, forming of door outer panel is investigated by Taguchi method. Main parameters are yield strength, thickness, blank size, blank holding force and so on. For the given value of design parameters, forming analysis of the eighteen cases are carried out according to L18 orthogonal array. After comparing the performance by simple conversion of simulation results into dent resistance, the final suggestion of the forming parameters is verified for the optimal improvement of dent resistance.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.17 no.3
• /
• pp.198-204
• /
• 2014

Ships sailing the seas encounter air resistance. The air resistance depends on the shape of the above-water hull, the ship speed, the wind speed and wind direction. The experimental or statistical methods which are used to predict the air resistance are one of the essential procedures of the calculation of the towing force of the disabled ships. This paper shows simplified air resistance prediction method using the variables of the projected area of the above-water hull, the speed of the ship, the wind speed and its direction. These methods have been applied to the existing computer program which had been set up to predict the towing force of the disabled ships.