• 대한치과의사협회지
• /
• 제53권3호
• /
• pp.178-186
• /
• 2015

Dental polymer-based luting materials are classified into esthetic resin cement, adhesive resin cement and self-adhesive resin cement. Due to the different component of each type of resin cement, the preconditioning method of tooth surface and the steps are different from each type of resin cement. The pre-treatment of adherend (ceramic, resin and metal) surface also varies with the type of resin cement and the manufacturer. In this study, the characteristics of each type of resin cement, mechanical properties, indication and advantages were investigated. Through these, clinical tips on using resin cements were suggested.

• 한국세라믹학회지
• /
• 제34권10호
• /
• pp.1037-1044
• /
• 1997

Mechanical properties and water stability of HAC/PVA based MDF cement composite were investigated using polyurethane(PU) resin, silane coupling agent and various PVA. The results were as follows ; The flexural strength of MDF cement composite increased as increasing with PVA content. Low-viscosity PVA developed higher flexural strength than high-viscosity PVA under a drying curing condition. But the strength of water immersed specimen decreased. Water stability of MDF cement improved as increasing with content of PU. Consequently, water stability of polyurethane 7% added MDF cement was about 2 times higher than that of the controlled specimen. Furthermore, the strength and water stability of diamine group based silane couling agent in using MDF cement increased and improved dramatically.

• The Journal of Advanced Prosthodontics
• /
• 제8권2호
• /
• pp.144-149
• /
• 2016

PURPOSE. The use of temporary or permanent cements in fixed implant-supported prostheses is under discussion. The objective was to compare the retentiveness of one temporary and two permanent cements after cyclic compressive loading. MATERIALS AND METHODS. The working model was five solid abutments screwed to five implant analogs. Thirty Cr-Ni alloy copings were randomized and cemented to the abutments with one temporary (resin urethane-based) or two permanent (resin-modified glass ionomer, resin-composite) cements. The retention strength was measured twice: once after the copings were cemented and again after a compressive cyclic loading of 100 N at 0.72 Hz (100,000 cycles). RESULTS. Before loading, the retention strength of resin composite was 75% higher than the resin-modified glass ionomer and 2.5 times higher than resin urethane-based cement. After loading, the retentiveness of the three cements decreased in a non-uniform manner. The greatest percentage of retention loss was shown by the temporary cement and the lowest by the permanent resin composite. However, the two permanent cements consistently show high retention values. CONCLUSION. The higher the initial retention of each cement, the lower the percentage of retention loss after compressive cyclic loading. After loading, the resin urethane-based cement was the most favourable cement for retrieving the crowns and resin composite was the most favourable cement to keep them in place.

• The Journal of Advanced Prosthodontics
• /
• 제3권3호
• /
• pp.119-125
• /
• 2011

PURPOSE. The aim of this study was to evaluate the influence of resin cement thickness on the microtensile bond strength between zirconium-oxide ceramic and resin cement. MATERIALS AND METHODS. Thirty-two freshly extracted molars were transversely sectioned at the deep dentin level and bonded to air-abraded zirconium oxide ceramic disks. The specimens were divided into 8 groups based on the experimental conditions (cement type: Rely X UniCem or Panavia F 2.0, cement thickness: 40 or 160 ${\mu}m$, storage: thermocycled or not). They were cut into microbeams and stored in $37^{\circ}C$ distilled water for 24 h. Microbeams of non-thermocycled specimens were submitted to a microtensile test, whereas those of thermocycled groups were thermally cycled for 18,000 times immediately before the microtensile test. Three-way ANOVA and Sheffe's post hoc tests were used for statistical analysis (${\alpha}$=95%). RESULTS. All failures occurred at the resin-zirconia interface. Thermocycled groups showed lower microtensile bond strength than non-thermocycled groups (P<.001). Differences in cement thickness did not influence the resin-zirconia microtensile bond strength given the same resin cement or storage conditions (P>.05). The number of adhesive failures increased after thermocycling in all experimental conditions. No cohesive failure was observed in any experimental group. CONCLUSION. When resin cements of adhesive monomers are applied over air-abraded zirconia restorations, the degree of fit does not influence the resin-zirconia microtensile bond strength.

• 한국세라믹학회지
• /
• 제35권4호
• /
• pp.371-377
• /
• 1998

HAC/PVA계 MDF 시멘트 복합재료의 수분안정성을 향상시키기 위하여 수용성 epoxy resm을 시멘트 중량에 대해 5wt% 에서 15wt%까지 첨가하고 calendering법, extruding법, warm pressing법으로 성형하여 epoxy resin첨가량 및 제조공정이 수분안정성에 미치는 영향을 살펴보았다. 제조된 시편은 건조상태 및 3일, 7일, 14일간 물 속에 침적 후 습윤강도를 3점 곡강도로 측정하고 SEM으로 표면 가까운 부분의 파단면을 관찰하고 수은압입법으로 기공분포 및 기공율을 분석하여 침수 재령벌 MDF 시멘트 복합재료의 미세조직 변화를 살펴보았다. 적량의 epoxy resin 첨가에 의해 건조강도는 감소하였으나 전반적으로 수분안정성이 향상되었다. 그러나 전반적으로 epoxy의 함량이 많아지면 초기건조강도는 감소하는 경향을 나타나었으며 epoxy 첨가량이 7wt% 이상일 경우에서는 수분안정성 역시 별다른 효과를 볼 수 없었다. 제조공정별로는 warm pressing법에 의해 성형된 경우 epoxy 첨가에 의한 강도 및 수분안정성 향상 효율이 다른 방법보다 월등히 뛰어났으며 epoxy resinmdmf 5wt%, 7wt% 첨가하였을 때, 최적의 강도 및 수분안정성 효과를 얻을 수 있었다.

• 한국농공학회지
• /
• 제26권1호
• /
• pp.52-72
• /
• 1984

This study was performed to obtain the basic data which can be applied to the use of epoxy resin mortars. The data was based on the properties of epoxy resin mortars depending upon various mixing ratios to compare those of cement mortar. The resin which was used at this experiment was Epi-Bis type epoxy resin which is extensively being used as concrete structures. In the case of epoxy resin mortar, mixing ratios of resin to fine aggregate were 1: 2, 1: 4, 1: 6, 1: 8, 1:10, 1 :12 and 1:14, but the ratio of cement to fine aggregate in cement mortar was 1 : 2.5. The results obtained are summarized as follows; 1.When the mixing ratio was 1: 6, the highest density was 2.01 g/cm$^3$, being lower than 2.13 g/cm$^3$ of that of cement mortar. 2.According to the water absorption and water permeability test, the watertightness was shown very high at the mixing ratios of 1: 2, 1: 4 and 1: 6. But then the mixing ratio was less than 1 : 6, the watertightness considerably decreased. By this result, it was regarded that optimum mixing ratio of epoxy resin mortar for watertight structures should be richer mixing ratio than 1: 6. 3.The hardening shrinkage was large as the mixing ratio became leaner, but the values were remarkably small as compared with cement mortar. And the influence of dryness and moisture was exerted little at richer mixing ratio than 1: 6, but its effect was obvious at the lean mixing ratio, 1: 8, 1:10,1:12 and 1:14. It was confirmed that the optimum mixing ratio for concrete structures which would be influenced by the repeated dryness and moisture should be rich mixing ratio higher than 1: 6. 4.The compressive, bending and splitting tensile strenghs were observed very high, even the value at the mixing ratio of 1:14 was higher than that of cement mortar. It showed that epoxy resin mortar especially was to have high strength in bending and splitting tensile strength. Also, the initial strength within 24 hours gave rise to high value. Thus it was clear that epoxy resin was rapid hardening material. The multiple regression equations of strength were computed depending on a function of mixing ratios and curing times. 5.The elastic moduli derived from the compressive stress-strain curve were slightly smaller than the value of cement mortar, and the toughness of epoxy resin mortar was larger than that of cement mortar. 6.The impact resistance was strong compared with cement mortar at all mixing ratios. Especially, bending impact strength by the square pillar specimens was higher than the impact resistance of flat specimens or cylinderic specimens. 7.The Brinell hardness was relatively larger than that of cement mortar, but it gradually decreased with the decline of mixing ratio, and Brinell hardness at mixing ratio of 1 :14 was much the same as cement mortar. 8.The abrasion rate of epoxy resin mortar at all mixing ratio, when Losangeles abation testing machine revolved 500 times, was very low. Even mixing ratio of 1 :14 was no more than 31.41%, which was less than critical abrasion rate 40% of coarse aggregate for cement concrete. Consequently, the abrasion rate of epoxy resin mortar was superior to cement mortar, and the relation between abrasion rate and Brinell hardness was highly significant as exponential curve. 9.The highest bond strength of epoxy resin mortar was 12.9 kg/cm$^2$ at the mixing ratio of 1:2. The failure of bonded flat steel specimens occurred on the part of epoxy resin mortar at the mixing ratio of 1: 2 and 1: 4, and that of bonded cement concrete specimens was fond on the part of combained concrete at the mixing ratio of 1 : 2 ,1: 4 and 1: 6. It was confirmed that the optimum mixing ratio for bonding of steel plate, and of cement concrete should be rich mixing ratio above 1 : 4 and 1 : 6 respectively. 10.The variations of color tone by heating began to take place at about 60˚C, and the ultimate change occurred at 120˚C. The compressive, bending and splitting tensile strengths increased with rising temperature up to 80˚ C, but these rapidly decreased when temperature was above 800 C. Accordingly, it was evident that the resistance temperature of epoxy resin mortar was about 80˚C which was generally considered lower than that of the other concrete materials. But it is likely that there is no problem in epoxy resin mortar when used for unnecessary materials of high temperature resistance. The multiple regression equations of strength were computed depending on a function of mixing ratios and heating temperatures. 11.The susceptibility to chemical attack of cement mortar was easily affected by inorganic and organic acid. and that of epoxy resin mortar with mixing ratio of 1: 4 was of great resistance. On the other hand, when mixing ratio was lower than 1 : 8 epoxy resin mortar had very poor resistance, especially being poor resistant to organicacid. Therefore, for the structures requiring chemical resistance optimum mixing of epoxy resin mortar should be rich mixing ratio higher than 1: 4.

• 한국농공학회논문집
• /
• 제59권6호
• /
• pp.19-27
• /
• 2017

This study investigated to predict the compressive strength of unsaturated polyester resin based polymer concrete using the maturity method. The test results show that the development of the compressive strength increased exponentially until an age of 24 hours. After 24 hours, the development of the compressive strength just increased gradually. This test result shows that the strength of unsaturated polyester resin based polymer concrete was developed mainly at the early age. Estimated datum temperature of unsaturated polyester resin based polymer concrete was $-20.67^{\circ}C$ which was much lower than of datum temperature ($-10^{\circ}C$) of Portland cement concrete. Also, this study result shows that the existing maturity index associated with Portland cement concrete was not applicable for polymer concrete because curing time of Portland cement concrete is different clearly with curing time of polymer concrete. The cause of different curing time was that there were different curing mechanisms between Portland cement concrete and polymer concrete. In order to best apply the experimental data to a model, CurveExpert Professional, the commercial software, was used to determine the predictive model regarding the compressive strength of unsaturated polyester resin based polymer concrete. As a result, Gompertz Relation or Weibull Model was an appropriate model as a predictive model. The proposed model can be used to predict the compressive strength, especially, it is more useful when the maturity is in the range between $40^{\circ}C{\cdot}h^{0.4}$ and $900^{\circ}C{\cdot}h^{0.4}$.

• Restorative Dentistry and Endodontics
• /
• 제33권6호
• /
• pp.553-559
• /
• 2008

이 연구의 목적은 레진 코팅된 표면과 레진인레이 사이의 자가-접착 레진시멘트를 이용한 결합 시 임시가봉제에 따른 미세인장결합강도를 평가하는 것이었다. Caviton(GC, Tokyo, Japan), Provifil(Promedica, Neumunster, Germany), Provifil(Promedica, Neumunster Germany) & petrolatum, and Eugenol-based cement, Tembond(Kerr, Orange. CA, USA) 이 임시가봉재로 사용되었다. Tescera(Bisco, Schamburg IL, USA) 로 제작하였고 자가-접착 레진시멘트인 Rely X unicem (3M, St. Paul. Minn, USA) 를 이용하여 접착하였다. 이후 미세인 장결합강도를 측정하였고 one-way anova 와 Duncan test 를 이용하여 분석하였다.(p<0.05) Caviton 군이 다른 그룹과 비교하여 유의성 있는 차이를 보여주었다(p<0.05). Provifil, Provifil & petrolatum, Tembond 군 등은 상대적으로 낮은 값을 보여주었다.

• 대한치과재료학회지
• /
• 제45권4호
• /
• pp.233-242
• /
• 2018

본 연구의 목적은 레진시멘트 색상이 상용 지르코니아 크라운의 색상에 미치는 영향을 평가하는 것이다. 연구에는 $NuSmile^{(R)}$ ZR Zirconia LT Shade (LT) 지르코니아와 $RelyX^{TM}$ U200 TR, A2, A3O (TR, A2, A3O) 레진시멘트를 사용했다. 이 때 지르코니아와 레진시멘트 시편은 직경 5 mm, 두께 1 mm의 디스크 형으로 각 조건 당 다섯 개씩 제작했다. CIE $L^*a^*b^*$값은 검은색과 흰색 배경에서 분광 광도계를 사용해 지르코니아와 레진시멘트 단독 조건과 겹친 조건에서 각각 측정했다. 레진시멘트 색상이 상용 지르코니아 크라운의 색상에 미치는 영향은 측정된 값을 이용해, 반투명도(TP, translucency parameter), 대조비(CR, contrast ratio), 색차(${\Delta}E{^*}_{ab}$)의 계산을 통해 평가했다. 각 변수에 대한 평균값과 표준편차는 동일한 실험군에서 CIE $L^*a^*^b^*$ 값을 3회씩 측정하여 구했다. 실험군의 통계적 유의성은 일원배치 분산분석(one-way ANOVA)과 Tukey-multiple comparisons test로 검증했다. 그 결과, 지르코니아 하방에 레진시멘트를 겹친 조건일 때는 지르코니아 단독 조건일 때에 비해 반투명도는 감소했고(p<0.05) 대조비는 증가했다. 검은색 배경에서 지르코니아와 지르코니아 하방에 레진시멘트를 겹쳤을 때의 색차는 모든 실험군에서 색의 변화를 인지할 수 없었고 LT/A3O 조합에서 최소값을 보였다. 한편, 흰색 배경에서 지르코니아와 지르코니아 하방에 레진시멘트를 겹쳤을 때의 색차는 LT/TR 조합에서 색변화를 임상적으로 허용할 수 있는 경계값을 보였다. LT/A2 조합에서는 색변화를 임상적으로 허용할 수 없었고, LT/A3O 조합에서는 색변화를 인지할 수 있었으나 임상적으로 허용할 수 있는 수준이었다. 이상의 결과와 같이 본 연구의 한계 내에서는, 흰색 배경의 LT/A2 조합 외에는 지르코니아 색상에 임상적으로 허용할 수 없는 색변화를 주는 레진시멘트는 없었다. 그 중 지르코니아 색상에 최소한의 영향을 미치는 레진시멘트 색상은 A3O였다. 따라서, 본 연구와 동일한 상용 지르코니아 크라운을 치아에 접착할 때 색변화를 최소화하기 위해서는 A3O 색상의 레진시멘트 사용이 추천된다.

• Restorative Dentistry and Endodontics
• /
• 제41권3호
• /
• pp.167-175
• /
• 2016

Objectives: Endodontically treated teeth with insufficient tooth structure are often restored with esthetic restorations. This study evaluated the cytotoxicity and biological effects of yttria partially stabilized zirconia (Y-TZP) blocks in combination with several dental cements. Materials and Methods: Pairs of zirconia cylinders with medium alone or cemented with three types of dental cement including RelyX U200 (3M ESPE), FujiCEM 2 (GC), and Panavia F 2.0 (Kuraray) were incubated in medium for 14 days. The cytotoxicity of each supernatant was determined using 3-(4,5-dimethylthiazole- 2-yl)-2,5-diphenyltetrazolium bromide (MTT) assays on L929 fibroblasts and MC3T3-E1 osteoblasts. The levels of interleukin-6 (IL-6) mRNA were evaluated by reverse transcription polymerase chain reaction (RT-PCR), and IL-6 protein was evaluated by enzyme-linked immunosorbent assays (ELISA). The data were analyzed using one-way ANOVA and Tukey post-hoc tests. A p < 0.05 was considered statistically significant. Results: The MTT assays showed that MC3T3-E1 osteoblasts were more susceptible to dental cements than L929 fibroblasts. The resin based dental cements increased IL-6 expression in L929 cells, but reduced IL-6 expression in MC3T3-E1 cells. Conclusions: Zirconia alone or blocks cemented with dental cement showed acceptable biocompatibilities. The results showed resin-modified glass-ionomer based cement less produced inflammatory cytokines than other self-adhesive resin-based cements. Furthermore, osteoblasts were more susceptible than fibroblasts to the biological effects of dental cement.