• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.205-208
• /
• 2001

Steady state and transient thermal analysis has been done by a finite element method in a diode of 12kV blocking voltage for microwave oven. The diode was fabricated by soldering ten pieces of 1200V diodes in series, capping a dummy wafer at the far end of diode series, and finally copper wire bonded for building anode and cathode terminal. In order to achieve high voltage and reliability, the edge of each diode was beveled and passivated by resin and epoxy with a thickness of 25$\mu\textrm{m}$ and 3,700$\mu\textrm{m}$, respectively. The chip size, thickness and material properties were very important factor for high voltage diode package. And also, thermal stress value was highest in the edge of diode and solder. So, design of edge in silicon was very important to thermal stress.

• Restorative Dentistry and Endodontics
• /
• 제24권3호
• /
• pp.503-510
• /
• 1999

The purpose of this study was to evaluate the amount of transportation of original canal, zip formation, permanent deformation and fracture of instruments after canal enlargement. In this study, the 60 resin blocks that have curved canals were randomly divided into 3 experimental groups with 20 teeth each according to instrument types and filling methods for canal enlargement. The curved canals of each experimental groups were enlarged to No 40 ISO size with the K-flexo stainless steel file (Group 1), Engine-driven Ni-Ti Profile new series(Group 2) and Engine-driven Ni-Ti Quantec 2000 series(Group 3) according to the manufacturer's recommendation. Pre- and postoperative X-rays were taken at same position and the films were scanned and the canal images were traced to determine the canal curvature according to the method of Schneider. The amount of reduction in canal curvature were calculated between pre- and postoperative X-rays. In addition to zip formation, permanent deformation and fracture of instruments were examined after canal enlargement. The results were as follows : 1. All experimental groups showed some loss of canal curvature after instrumentation. There was a significant change in curvature between before and after instrumentation in each group(p<0.001). 2. Engine-driven Ni-Ti instrumentations resulted in an average loss of curvature of 2.36 degrees for Profile new series, 3.43 degrees for Quantec series, and hand instrumentation showed an average loss of curvature of 6.48 degrees for K-flexo file. There was a statistical significant difference between hand instrumentation and engine-driven Ni-Ti instrumentations(p<0.05). But there was no statistical difference between Profile new series and Quantec series. 3. There were many apical zip formations in group 1(Hand instrumentation). But there were no apical zip formations in group 2,3(Engine-driven Ni-Ti instrumentation). 4. The instrument deformation occured 9 cases in group 1(K-flexo file), 2 cases in group 2(Profile new series) and 3 cases in group 3(Quantec) after instrumentation. And the instrument fracture occured 1 case in each group. The results showed that the engine-driven Ni-Ti instruments, if we use carefully according to manufacturer's recommendations, can be use effectively for instrumenting the curved root canals in case of the MAF was over size 40.

• 한국정밀공학회지
• /
• 제28권7호
• /
• pp.777-782
• /
• 2011

Micro features on the surface are well-known to have significant effects on optical or mechanical properties such as the optical interference, reflectance at the surface, contact angle, interfacial friction, etc. These surface micro features are increasingly employed to enhance the functionality of the applications in various application areas such as optical components for LCD or solar panel. Diverse surface features have been proposed and some of them are showing excellent efficiency or functionality, especially in optical applications. Most applications employing the micro features need manufacturing process for mass production and the injection molding and roll-to-roll forming, which are typical processes for mass production adopting polymeric materials, may be also preferred for micro patterned plastic product. Since the functionality or efficiency of the surface structures generally depends on the shape and the size of the structure itself or the array of the structures on the surface, it would be very important to replicate the features very precisely as being designed during the molding the micro pattern applications. In this paper, a series of research activities is introduced for roll-to-roll forming of micro patterned film including filling of patterns with UV curable resin, demolding of surface structures from the roll tool, control of surface energy and cure shrinkage of resin and dispose time and intensity of the UV light for curing of UV curable resin.

• 콘크리트학회논문집
• /
• 제19권4호
• /
• pp.421-431
• /
• 2007

본 연구의 주 목적은 유리 및 탄소단섬유 (chopped fiber)와 에폭시 및 비닐에스터수지 (resin)를 외기에서 혼합하여 요철이 많은 콘크리트 표면에 고속의 압찰 공기로 랜덤하게 분사하여 기존 콘크리트 구조물을 보강하는 새로운 공법, 즉 sprayed FRP 보수보강 공법을 개발하는 것으로서, 본 연구에서는 sprayed FRP 보강을 위한 치적의 재료 물성치를 제시하고자 유리 및 탄소단섬유의 길이, 단섬유와 에폭시 및 비닐에스터수지의 배합 비율 등을 주요변수로 설정하여 재료 인장시험을 실시하였다. 또한 상기 재료 시험 결과를 바탕으로 sprayed FRP 공법을 이용하여 보강된 철근콘크리트 휨 보, 전단 보 및 손상 보의 보강 성능을 실험적 연구를 토대로 평가하였다. 그 결과, 유리 및 탄소단섬유의 길이 38 mm, 섬유와 수지의 배합 비율 1 : 2가 최적 물성치로 제안되었으며, sprayed FRP의 휨 및 전단 보의 보강 효과는 기존 FRP sheet와 유사한 보강 효과를 나타냈으며, 손상 보의 경우 최대 강도의 결과를 비교해보면 보강 보와 동등한 보강 효과가 나타났다. 기존 FRP 설계식의 적용 가능성을 분석해본 결과, sprayed FRP 휨실험체의 경우 기존설계식의 적용이 가능한 것으로 드러났으며, 전단실험체의 경우는 전단강도 저감계수 ${\alpha}=0.18$이 실험값과 근접한 범위 내에서 안전 측으로 설계가 되는 것으로 사료된다.

• 약학회지
• /
• 제29권3호
• /
• pp.144-151
• /
• 1985

Cathodic stripping voltammetric determination of traces of selenium in plant samples was studied. Stripping peak of selenium (IV) from Cu-Se intermettalic deposit in acidic media containing copper (II) ion is specific, highly sensitive and well defined, is successfully used for the quantitative determination of selenuin down to the level of 1ng/ml. Sample is burnt in a calorimeter bomb under the oxygen pressure of 40atm. and the selenium is absorbed in 0.1M NaOH. After the solution is filtrated, concentrated and acidified with HCl, then passed through a column of cation exchange resin in the $H^{+}$ form(Dowex 50X-8). The column eluate is analyzed for selenium by differential pulse cathodic stripping voltammetric method. Analytical results of selenium for NBS SMR is well agreement with the certified values. Results are given for a series of plant materials.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 춘계학술대회 논문집
• /
• pp.164-167
• /
• 1997

A series of interpenetrating polymer networks(IPN) based on Epoxy, MA and PU were synthesized in order to improve withstand voltage properties of Epoxy resin. Dielectric breakdown characteristics are investigated for six types of specimens. As a result, it was found that impulse voltage dielectric breakdown characteristic of SIN specimen was the most excellent. It was also found that SIN specimens were stronger than anything else in scanning electron microscopy. On the other hand, as a result of consideration of dielectric breakdown strength change according to adding fi1ter, it was confirmed that the decrease of dielectric breakdown strength are controlled slightly by IPN method.

• 한국기계가공학회지
• /
• 제4권2호
• /
• pp.10-15
• /
• 2005

For the development of compensation machining program, ultra precision grinding used in ultra precision machine and corrective machining was studied. We explored a new rough grinding technique on optical material such as zerodur. The facility used is a polishing machine with a custom grinding module and a range of diamond resin bond wheel. Surface roughness and form accuracy are measured by surface measurement equipment(Form Talysurf series2). Our compensation machining program has complied with a target of producing surface roughness better than $0.05{\mu}m$ Ra and form accuracy of around $0.05{\mu}m$ Rt and has been unveiled as a work-hour model.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 춘계학술대회 논문집
• /
• pp.405-409
• /
• 2003

We explored a new rough grinding technique on optics materials such as Zerodur. The facility used is a NANOFORM-600 diamond turning machine with a custom grinding module and range of diamond resin bond wheel. The grinding parameters such as workpiece rotation speed depth of cut and feed rate were altered while grinding the workpiece surfaces of 20m in diameter. Surface roughness is measured by Form Talysurf series2. Our target is to define grinding conditions producing the surface roughness better than 0.02${\mu}{\textrm}{m}$ Ra and the form accuracy of around 0.2${\mu}{\textrm}{m}$ PV.

• 한국기계가공학회지
• /
• 제4권1호
• /
• pp.13-17
• /
• 2005

We explored a new rough grinding technique on optics materials such as Zerodur. The facility used is a NANOFORM-600 diamond turning machine with a custom grinding module and a range of diamond resin bond wheel. The grinding parameters such as workpiece rotation speed, depth of cut and feed rate were altered while grinding the workpiece surfaces of 20mm in diameter. Surface roughness was measured by Form Talysurf series2. Our target is to define grinding conditions producing the surface roughness smaller than $0.2{\mu}m$ Ra.

• 공기청정기술
• /
• 제22권2호
• /
• pp.40-49
• /
• 2009

Aluminum thin plate coated with epoxy resin containing about 20wt% brass powder, was applied to fins of heat exchanger. We carried out a series of detailed examinations to evaluate the anti-bacterial performance of the plate and heat exchanger (fan coil unit). In the presence of water or moisture, copper ions which have an anti-bacterial ability eluted from brass powder and showed sufficient effects on many kinds of bacteria. We also evaluated the anti-bacterial performance quantitatively by use of the index API (Anti-bacterial Performance Index) which has already been proposed by authors.