• Advanced Composite Materials
• /
• 제16권4호
• /
• pp.283-298
• /
• 2007

Environment-friendly composites reinforced with bagasse fiber (BF), a kind of natural fiber as the remains from squeezed sugarcane, were fabricated by injection molding and press molding. As appropriate matrices for injection molding and press molding, polypropylene (PP) and polycaprolactone-cornstarch (PCL-C) were selected, as a typical recyclable resin and biodegradable resin, respectively. The mechanical properties of BF/PP composites were investigated in view of fiber mass fraction and injection molding conditions. And the mechanical properties and the biodegradation of BF/PCL composites were also evaluated. In the case of injection molding, the flexural modulus increased with an increase in fiber mass fraction, and the mechanical properties decreased with an increase in cylinder temperature due to the thermal degradation of BF. The optimum conditions increasing the flexural properties and the impact strength were $90^{\circ}C$ mold temperature, 30 s injection interval, and in the range of 165 to $185^{\circ}C$ cylinder temperature. On the other hand, as to BF/PCL-C fully-green composites, both the flexural properties and the impact strength increased with an increase in fiber mass fraction. It is considered that the BF compressed during preparation could result in the enhancement in mechanical properties. The results of the biodegradability test showed the addition of BF caused the acceleration of weight loss, which increased further with increasing fiber content. This reveals that the addition and the quantities of BF could promote the biodegradation of fully-green composites.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권2호
• /
• pp.139-145
• /
• 1998

Filament winding method is widely used for composite fabrications using low viscosity liquid for-mation and processing asymmetrical structures of pressure vessel pipe rocket motor case etc. The filament winding method is affected by several parameters such as pot life of process time viscosi-ty of resin filament winding temperature and schedules curing condition and post curing condi-tion of resin. To develope high functional composite materials the rotation(5, 15, 20, 30rpm) of the winding machine was controlled by D.C motor. And the wiper to give proper tension was equipped between strand and resin bath. The resin is hooked by the design wiper. The adequate cure schedule was found by DSC. NOL ring test is carried out to investigate the basic physical properties such as design technology. The void contents in filament winding is generally higher than that of the prepreg laminated plate. These high contents of void can make a crack in resin in spite of low deformation. These problem was solved by giving tension in processing. To improve the characteristics of fiber volume fraction void contents resin/fiber bonding the winding speedc is changed under constant tension. It was found that resin impregnation was not different from in fiber contents void contents at the range of 0.5~1kg tension but it was found that resin was not impregnated at the above of 1.5kg tension. In burst test a pure PE liner was failed at a nozzle part under the $14kg/\textrm{cm}^2$ pressure but a pressure vessel of CNG was failed at a cylinder part under the $200kg/\textrm{cm}^2$ pressure.

• International Journal of Ocean System Engineering
• /
• 제3권2호
• /
• pp.102-110
• /
• 2013

The purpose of this study was to improve the properties of epoxy resin using titanium oxide nanoparticles. The effects of particle weight fraction, dispersion agent, and curing agents with different molecular weights on the thermal and mechanical properties of titanium-oxide-reinforced epoxy resin were investigated. In addition, the effect of the particle dispersion condition on the mechanical properties of nanocomposites was studied. As a result, it was found that the glass transition temperature of film-shaped nanocomposites decreased with an in-crease in the nanoparticle content. Because nanoparticles interrupted the cross linkage between the epoxy resin and the amine curing agent, the cross-link density of the epoxy became lower and led to a decrease in $T_g$ in the nanocompo-sites. The tensile strength and modulus in film-shaped nanocomposites also increased with the particles content. But in the case of dog-bone-shaped nanocomposites, the values were not similar to the trend for the film-shaped nanocompo-sites. This was probably a result of the different nanoparticles dispersions in the epoxy resins resulting from the respective-thicknesses of the film and dog-bone-shaped samples.

• 분석과학
• /
• 제18권6호
• /
• pp.469-474
• /
• 2005

본 연구에서는 음이온 교환수지와 Sr-Spec 수지를 사용하여 토양중 $^{90}Sr$, $^{241}Am$ 및 Pu 동위원소들에 대하여 축차적으로 분리하는 정량법을 제시하였다. 플루토늄은 음이온 교환수지를 이용하여 분리하였고, 아메리슘 및 스트론튬은 옥살산 공침법 및 Sr-Spec 수지를 사용하여 순수 분리하였다. Pu 및 Am 동위원소는 알파 스펙트로메트리법으로 정량하였고, Sr-90은 액체섬광계수기를 사용하여 정량하였다. 본 연구에서 고찰된 $^{90}Sr$, $^{241}Am$ 및 Pu 동위원소 분석법을 IAEA 기준시료에 적용하여 분석법의 타당성을 검증하였다.

• 한국인쇄학회지
• /
• 제15권2호
• /
• pp.107-115
• /
• 1997

The ultraviolet(UV)-curable materials are widely used in inks and coatings. In this paper is designed to develop materials having flexibility and functionality with UV-curable acrylate monomer and alkyd resin. At first, phase diagram is prepared for miscibility of UV -curable acrylate monomer with alkyd resin. Also the gel fraction and dynamic viscosity are measured to curing speed of mixing system. In results, it has been demonstrated that miscibility and curing speed are greatly influenced by alkyd resin content.

• Asian Journal of Atmospheric Environment
• /
• 제6권1호
• /
• pp.67-72
• /
• 2012

The chemical characterization of water-soluble organic carbon in ash emitted from a coal combustion boiler has not been reported yet. A total of 5 ash samples were collected from the outlet of an electrostatic precipitator in a commercial 500 MW coal-fired power plant, with their chemical characteristics investigated. XAD7HP resin was used to quantify the hydrophilic and hydrophobic water-soluble organic carbons (WSOC), which are the fractions of WSOC that penetrate and remain on the resin column, respectively. Calibration results indicate that the hydrophilic fraction includes aliphatic dicarboxylic acids and carbonyls (<4 carbons), amines and saccharides, while the hydrophobic fraction includes aliphatic dicarboxylic acids (>4-5 carbons), phenols, aromatic acids, cyclic acid and humic acid. The average mass of the WSOC in the ash samples was found to depend on the bituminous coal type being burned, and ranged from 163 to 259 ${\mu}g$ C/g of ash, which corresponds to 59-96 mg C of WSOC/kg of coal combusted. The WSOC mass accounted for 0.02-0.03 wt% of the used ash sample mass. Based on the flow rate of flue gas produced from the combustion of the blended coals in the 500 MW coal combustion boiler, it was estimated that the WSOC particles were emitted to the atmosphere at flow rates of 4.6-7.2 g C/hr. The results also indicated that the hydrophilic WSOC fraction in the coal burned accounted for 64-82% of the total WSOC, which was 2-4 times greater than the mass of the hydrophobic WSOC fraction.

• 한국식품과학회지
• /
• 제32권3호
• /
• pp.610-617
• /
• 2000

높은 난소화성 획분을 갖는 난소화성 덱스트린은 열처리 덱스트린의 효소 가수분해액을 에탄올 또는 강산성 양이온 교환수지(UBK 530)로 처리함으로써 제조하였다. 난소화성 획분, 식이섬유 및 수출을 고려하여 ${\alpha}-amylase$와 amyloglucosidase를 반응시킨 가수분해액으로부터 난소화성 덱스트린을 제조하기 위한 에탄올 처리의 최적 조건은 에탄올을 30%(w/w) 효소 반응액에 고형분 대비 5배로 첨가하여 상온에서 3시간 동안 방치시키는 공정이었다. 포도당을 포함하는 저분자 당류와 고분자 당류를 강산성 양이온 교환수지에 의해 분리한 결과 내열성 ${\alpha}-amylase$와 amyloglucosidase에 의한 초기 효소 반응액은 43.6%의 DPI(glucose)과 51.5%의 DP4+(maltotetaos이상)를 나타낸 반면, 양이온 교환수지에 의해 초기 효소 반응액의 50%까지 분취한 난소화성 덱스트린은 7.1%의 DPI(glucose)과 91.2%의 DP4+(maltoteoaose이상)를 나타내었다. 따라서, 초기 효소 반응액의 난소화성 획분 44.5%는 저분자 당류의 분리 후 78.9%까지 증가하였다.

• 동력기계공학회지
• /
• 제14권4호
• /
• pp.68-75
• /
• 2010

The effect of dispersion agent, the content and size of nanoparticle on the mechanical and thermal properties has been investigated in $TiO_2$ nanoparticle/epoxy resin composites(nanocomposites). The weight fraction of fabricated nanocomposites were 0, 1, 3, 5%, respectively. The glass transition temperature was lower than pure epoxy resin and decreased with the increasing of nanopaticle content. This is considered that the cross link of epoxy resin during solidification was hindered by the presence of nanoparticles. Nanocomposites of 3wt% content with dispersion agent showed the best tensile strength. The tensile strength of 20㎚ $TiO_2$ nanocomposites were higher than one of 200nm $TiO_2$ nanocomposites.

• Advanced Composite Materials
• /
• 제16권2호
• /
• pp.181-194
• /
• 2007

This paper presents the mechanical properties of a composite consisting of acrylonitrile-butadiene-styrene (ABS) resin mixed with carbon fiber reinforced plastics (CFRP) pieces (CFRP/ABS). CFRP pieces made by crushing CFRP wastes were utilized in this material. Nine kinds of CFRP/ABS compounds with different weight fraction and size of CFRP pieces were prepared. Firstly, tensile and flexural tests were performed for the specimens with various CFRP content. Next, fracture surfaces of the specimens were microscopically observed to investigate fracture behavior and fiber/resin interface. Finally, the tensile modulus and strength were discussed based on the macromechanical model. It is found that the elastic modulus increases linearly with increasing CFRP content while the strength changes nonlinearly. Microscopic observation revealed that most carbon fibers are separated individually and dispersed homogeneously in ABS resin. Epoxy resin particles originally from CFRP are dispersed in ABS resin and seem to be in good contact with surrounding resin. The modulus and strength can be expressed using a macromechanical model taking account of fiber orientation, length and interfacial bonding in short fiber composites.

• Journal of Ginseng Research
• /
• 제22권3호
• /
• pp.155-160
• /
• 1998

This stuffy was carried to establish a new efficient method for the preparation of edible crude ginseng saponin. The conventional butanol extraction and resin adsorption methods were compared for the contents of total crude ginseng saponin and major ginsenosides. Seventy- percent methanol extract was applied to Diaion HP-20 column and the resin was washed with Hn and eluted with absolute methanol. The methanol elute was dried in vivo and analyzed for its ginsenosides. Use of ethanol instead of methanol to make edible crude ginseng saponin gave a similar result. Butanol extraction was performed by the conventional method. The final aqueous layer from butanol extraction was passed through Diaion HP-20 column followed by elution with methanol and Diaion HP-20 passed fraction was extracted with butanol to recover remaining components, respectively, in order to determine saponin loss. TLC and HPLC qualitatively and quantitatively monitored Ginsenosides, respectively. Loss of ginsenosides was higher in butanol extraction method than in Diction HP-20 adsorption method. In addition, saponin fractions prepared by Diction HP-20 adsorption method showed higher content of each ginsenoside, showing 8.2% higher purity than that of butanol extracted fraction. From these results, we propose the resin adsorption method as a new efficient measure for the preparation of crude ginseng saponin, which is edible by using spirit instead of methanol.