• Journal of Biomedical Engineering Research
• /
• v.20 no.1
• /
• pp.107-113
• /
• 1999

The purpose of this study was to develop a miniature imaging gamma probe with high performance that can detect small or residual tumors after surgery. Gamma probe detector system consists of NaI(Tl) scintillator, position sensitive photomultiplier tube (PSPMT), and collimator. PSPMT was optically coupled with 6.5 mm thick, 7.62 cm diameter of NaI(Tl) crystal and supplied with -1000V for high voltage. Parallel hexagonal hole collimator was manufactured for characteristics of 40-mm hole length, 1.3-mm hole diameter, and 0.22 mm septal thickness. Electronics consist of position and trigger signal readout systems. Position signals were obtained with summing, subtracting, and dividing circuit using preamplifer and amplifier. Trigger signals were obtained using summing amplifier, constant fraction discriminator, and gate and delay generator module with preamplifer. Data acquisition and processing were performed by Gamma-PF interface board inserted into pentium PC and PIP software. For imaging studies, flood and slit mask images were acquired using a point source. Two hole phantom images were also acquired with collimator. Intrinsic and system spatial resolutions were measured as 3.97 mm and 5.97 mm, respectively. In conclusion, Miniature gamma probe images based on the PSPMT showed good image quality, we conclude that the miniature imaging gamma probe was successfully developed and good image data were obtained. However, further studies will be required to optimize imaging characteristics.

• Journal of Navigation and Port Research
• /
• v.39 no.4
• /
• pp.345-351
• /
• 2015

This study investigated the optimum depth for the application of bioremediation in contaminated coastal sediment using a lab scale column experiment. The biostimulants were placed in the top surface of the sediment facing seawater, 3cm, 6cm and 10cm of the depth from the surface, respectibely. During the experiment, the changes of organic pollutants and heavy metal fractions in the sediment were monitored in 1 month and 3month time intervals. The organic pollutants found during various analysis such as chemical oxygen demand, total solids and volatile solids, significantly reduced when the depth of the biostimulant was 3cm or less. In contrast, at a depth of over 6cm, the reduction of organic pollutants decreased, and the results were similar to the control. Heavy metals fractions in the sediment also changed with the depth of the biostimulants. The exchangeable fraction of the metals was quite reduced at the sediment surface in the column, but the organic bound and residual fractions considerably increased at a depth of 3cm. Based on this study, the optimum biostimulants depth for in-situ bioremediation of contaminant coastal sediment is 3cm from the sediment surface.

• Korean Journal of Metals and Materials
• /
• v.56 no.11
• /
• pp.787-795
• /
• 2018

The effects of tempering condition on the microstructure and mechanical properties of 30MnB5 hot stamping steel were investigated in this study. Before the tempering, hot-stamped 30MnB5 steel was composed of only ${\alpha}^{\prime}$-martensite microstructure without precipitates. After the tempering at $180^{\circ}C$ for 120 min, nano-sized ${\varepsilon}$-carbides were precipitated in the ${\alpha}^{\prime}$-martensite laths. After tempering at $250^{\circ}C$ for 60 min, cementite was precipitated along the ${\alpha}^{\prime}$-martensite lath boundaries. The cementite was also observed in the specimens tempered at $350^{\circ}C$ for 30 min and $450^{\circ}C$ for 6 min, respectively. The globular ${\alpha}$-ferrite appeared at $350^{\circ}C-30min$ tempering, and the volume fraction of ${\alpha}$-ferrite increased when the tempering temperature was increased. The yield strength increased after tempering, and it reached a peak with the tempering condition of $180^{\circ}C-120min$, due to the nano-sized precipitates in the ${\alpha}^{\prime}$-martensite lath. After the tempering, the steel's ultimate tensile strength (UTS) was decreased due to the reduction in dislocation density and C segregation to lath boundaries. The highest elongation was observed at the $180^{\circ}C-120min$ tempering condition, due to the reduction of residual stress, and the lack of precipitates along the lath boundaries. The $180^{\circ}C-120min$ tempering condition was considered to have outstanding crash performance, according to toughness and anti-intrusion calculation results. In drop tower crash tests, the 30MnB5 door impact beam tempered at $180^{\circ}C$ for 120 min showed better crash performance compared to a 22MnB5 door impact beam.

• Journal of The Geomorphological Association of Korea
• /
• v.19 no.3
• /
• pp.37-49
• /
• 2012

The objective of this paper is to propose a methodology for surface sediments classification in tidal flats that can combine ground survey data with high-resolution remote sensing data by multivariate kriging. Unlike conventional methodologies that have classified remote sensing data by using pre-classified sediment components, a new classification methodology presented in this paper first generates sediment component fraction maps and then classifies the sediments on a final stage. For generating sediment component fractions, regression kriging, as one of multivariate kriging algorithms, is applied to integrate ground survey data and remote sensing data. First, trend components of sand, silt, and clay are derived through regression analysis of ground survey data and spectral information from remote sensing data. Then, residuals at sample locations are computed and interpolated to generate residual components in the study area. Finally, the sediment component fractions are computed by adding the residuals to the trend components and are classified on a final stage. A case study at the Baramarae tidal flats with KOMPSAT-2 imagery is carried out to evaluate the classification capability of the proposed classification methodology. Through the case study, the proposed methodology showed the best classification accuracy, compared with the conventional classification methodologies. Especially, much improvement of classification accuracy for fine-grained sediments were also obtained. Therefore, it is expected that the presented classification methodology would be an effective one for surface sediments classification in tidal flats.

• Korean Journal of Soil Science and Fertilizer
• /
• v.28 no.2
• /
• pp.176-182
• /
• 1995

Field and pot experiments were carried to find out the effects of direct application of phosphate rock powder on soybean plant in upland soils with different available P content. In newly reclaimed upland soil with extremely low available P, phosphate rock powder was superior to single superphosphate at the application rate of 400kg-600kg/ha, in the first year particularly. In the second year, however, the reverse was the case excepting at the rate of 200kg/ha. In upland soil with low avialble $P_2O_5$($52mg\;kg^{-1}$), the application of phosphate rock powder at the high appliaction rate(400-600kg/ha) increased the yield of soybean remarkably in the first year and there was residual effect in the second year. The application of phosphate rock at high rate, increased the P and Ca contenl of plant and soil. The concentration of all fractions of P in the soil at the harvest was higher in phosphate rock treatments than in single superphosphate and fused magnesium phosphate treatments. In this soil with low avaiable P the occurrence of different fractions of P was in the order of Org-P>Fe-P>Ca-P>Al-P, in the first year and there was no change in the second year.

• Journal of Korea Foundry Society
• /
• v.41 no.5
• /
• pp.419-433
• /
• 2021

Al-Si-Cu alloys benefit from the addition of copper for better hardness and strength through precipitation hardening, which results in remarkably strong alloys. However, the addition of copper expands the solidification range of Al-Si-Cu alloys, and due to this, these alloys become more prone to hot tearing, which is one of the most common and serious fracture phenomena encountered during solidification. The conventional evaluation method of the hot tearing properties of an alloy is a relative and qualitative analysis approach that does not provide quantitative data about this phenomenon. In the present study, the mold itself part of a device developed in Instone et al. was partially modified to obtain more reliable quantitative data pertaining to the hot tearing properties of an Al-Si-Cu casting alloy. To assess the influence of Cu element, four levels of Cu contents were tested (0.5, 1.0, 3.0, and 5.0 wt.%) in the Al-Si-Cu system alloy and the hot tearing properties were evaluated in each case. As the Cu content was increased, the hot tearing strength decreased to 2.26, 1.53, 1.18, and 1.04 MPa, respectively. At the moment hot tearing occurred, the corresponding solid fraction and solidification rate decreased at the same temperature due to the increase in the solid-liquid coexistence range as the Cu content increased. The morphology of the fracture surfaces was changed from dendrites to dendrites covered with residual liquid, and CuAl₂ phases were observed in the vicinity of hot tearing.

• Korean Journal of Materials Research
• /
• v.33 no.4
• /
• pp.142-150
• /
• 2023

AZO/Cu/AZO thin films were deposited on glass by RF magnetron sputtering. The specimens showed the preferred orientation of (0002) AZO and (111) Cu. The Cu crystal sizes increased from about 3.7 nm to about 8.5 nm with increasing Cu thickness, and from about 6.3 nm to about 9.5 nm with increasing heat treatment temperatures. The sizes of AZO crystals were almost independent of the Cu thickness, and increased slightly with heat treatment temperature. The residual stress of AZO after heat treatment also increased compressively from -4.6 GPa to -5.6 GPa with increasing heat treatment temperature. The increase in crystal size resulted from grain growth, and the increase in stress resulted from the decrease in defects that accompanied grain growth, and the thermal stress during cooling from heat treatment temperature to room temperature. From the PL spectra, the decrease in defects during heat treatment resulted in the increased intensity. The electrical resistivities of the 4 nm Cu film were 5.9×10^-4 Ω·cm and about 1.0×10^-4 Ω·cm for thicker Cu films. The resistivity decreased as the temperature of heat treatment increased. As the Cu thickness increased, an increase in carrier concentration resulted, as the fraction of AZO/Cu/AZO metal film increased. And the increase in carrier concentration with increasing heat treatment temperature might result from the diffusion of Cu ions into AZO. Transmittance decreased with increasing Cu thicknesses, and reached a maximum near the 500 nm wavelength after being heat treated at 200 ℃.

• Korean Journal of Radiology
• /
• v.22 no.10
• /
• pp.1719-1729
• /
• 2021

Objective: Emphysema and small-airway disease are the two major components of chronic obstructive pulmonary disease (COPD). We propose a novel method of quantitative computed tomography (CT) emphysema air-trapping composite (EAtC) mapping to assess each COPD component. We analyzed the potential use of this method for assessing lung function in patients with COPD. Materials and Methods: A total of 584 patients with COPD underwent inspiration and expiration CTs. Using pairwise analysis of inspiration and expiration CTs with non-rigid registration, EAtC mapping classified lung parenchyma into three areas: Normal, functional air trapping (fAT), and emphysema (Emph). We defined fAT as the area with a density change of less than 60 Hounsfield units (HU) between inspiration and expiration CTs among areas with a density less than -856 HU on inspiration CT. The volume fraction of each area was compared with clinical parameters and pulmonary function tests (PFTs). The results were compared with those of parametric response mapping (PRM) analysis. Results: The relative volumes of the EAtC classes differed according to the Global Initiative for Chronic Obstructive Lung Disease stages (p < 0.001). Each class showed moderate correlations with forced expiratory volume in 1 second (FEV₁) and FEV₁/forced vital capacity (FVC) (r = -0.659-0.674, p < 0.001). Both fAT and Emph were significant predictors of FEV₁ and FEV₁/FVC (R² = 0.352 and 0.488, respectively; p < 0.001). fAT was a significant predictor of mean forced expiratory flow between 25% and 75% and residual volume/total vital capacity (R² = 0.264 and 0.233, respectively; p < 0.001), while Emph and age were significant predictors of carbon monoxide diffusing capacity (R² = 0.303; p < 0.001). fAT showed better correlations with PFTs than with small-airway disease on PRM. Conclusion: The proposed quantitative CT EAtC mapping provides comprehensive lung functional information on each disease component of COPD, which may serve as an imaging biomarker of lung function.

• Journal of Cardiovascular Imaging
• /
• v.31 no.3
• /
• pp.125-132
• /
• 2023

BACKGROUND: There is limited data on the residual echocardiographic findings including strain analysis among post-coronavirus disease (COVID) patients. The aim of our study is to prospectively phenotype post-COVID patients. METHODS: All patients discharged following acute COVID infection were systematically followed in the post-COVID-19 Recovery Clinic at Vancouver General Hospital and St. Paul's Hospital. At 4-18 weeks post diagnosis, patients underwent comprehensive echocardiographic assessment. Left ventricular ejection fraction (LVEF) was assessed by 3D, 2D Biplane Simpson's, or visual estimate. LV global longitudinal strain (GLS) was measured using a vendor-independent 2D speckle-tracking software (TomTec). RESULTS: A total of 127 patients (53% female, mean age 58 years) were included in our analyses. At baseline, cardiac conditions were present in 58% of the patients (15% coronary artery disease, 4% heart failure, 44% hypertension, 10% atrial fibrillation) while the remainder were free of cardiac conditions. COVID-19 serious complications were present in 79% of the patients (76% pneumonia, 37% intensive care unit admission, 21% intubation, 1% myocarditis). Normal LVEF was seen in 96% of the cohort and 97% had normal right ventricular systolic function. A high proportion (53%) had abnormal LV GLS defined as < 18%. Average LV GLS of septal and inferior segments were lower compared to that of other segments. Among patients without pre-existing cardiac conditions, LVEF was abnormal in only 1.9%, but LV GLS was abnormal in 46% of the patients. CONCLUSIONS: Most post-COVID patients had normal LVEF at 4-18 weeks post diagnosis, but over half had abnormal LV GLS.

• Korean Journal of Environmental Agriculture
• /
• v.15 no.1
• /
• pp.1-10
• /
• 1996

The contents of heavy metals in soil near the Janghang smelter area were observed to understand present status and relationship between their fraction and the absorption by rice. The soil samples were taken from the eight sites of the paddy fields in 1982 and 1990, and analysis on heavy metals including Cd, Zn, Cu and Pb was performed. The results were as follows: Total contents of heavy metals in the samples of 1990 were higher than those of 1982. The order of increasing ratio was Cu > Zn > Pb > Cd and the variation of Cd content by sequential differente extracting was residual > exchangeable > dilute acid-extractable fractions and its increasing range was from 38 to 71% during nine years. The ratio of immobile heavy metals bound within an oxide or silicate matrix of Fe-Mn oxide bound and residual in surface soil was that Cd, Pb, Cu and Zn were 31.65, 42.22, 76.57 and 79.49%, respectively, and their mobile ratios of exchangeable, dilute acid-extractable and organically bound were more than 20.28%. Those of mobile Cd, Pb, Cu and Zn were 68.35, 55.78, 23.43 and 20.28%, respectively. Correlation between the heavy metal contents in surface soil and those in tissue of rice plant, such as leaf blade, leaf sheath, stem and panicle axis, were significant, but were not significant in subsurface soil. The dilute acid-extractable and organically bound fractions of Cd, Cu, Pb and Zn in surface soil were more significantly correlated with those in tissues of paddy rice.