• 한국전산유체공학회:학술대회논문집
• /
• 1998.05a
• /
• pp.29-34
• /
• 1998

An efficient 3-dimensional compressible solver is developed using the second-order upwind TVD scheme and the multigrid diagonalized ADI method. The multigrid method is improved so that the present DADI algorithm obtains better convergence rates. Results are computed on Cray C90 computer for transonic unsaperated flows past ONERA-M6 wing to demonstrate the accuracy and efficiency. The results show good agreement with experimetal data. A reduction of four orders of residual for 3-dimensional transonic flow is obtained about 99 seconds.

• Water for future
• /
• v.22 no.3
• /
• pp.289-298
• /
• 1989

A review is made of transient phenomena ralation to flow in the vadose zone. Reviewed topics include rapid water table response to rainfall, pulsating flow due to pressure perturbations in the vasoes zone, and the wave-like propagation of increased soil moisture caused by intermittent rainfall. As a basis of interpreting these phenomena, zoning of the vadose zone into a residual water zone, an unsaturated capillaty zone, and a saturated capillary zone are proposed. Possible implications with respect to hydrological processes relating to these phenomena are discussed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.3
• /
• pp.274-281
• /
• 2013

The variable demand on the energy market requires a great flexibility in operating hydro turbines. However, Francis turbine operated at off-design conditions poses technical challenges related to large unsteady forces given by residual swirl and angular momentum. In order to improve the performance of a Francis turbine, the paper presents a numerical investigation of the 3D flow in the turbine at off-design conditions and discusses the influence of variable guide vane openings on the internal flow of a Francis turbine with the help of computational fluid dynamics. First, the internal flow characteristics of Francis turbine operated by varied guide vane angle at off design condition are computed and the optimal guide vane angle is obtained. Secondly, the Francis turbine is operated with guide vane number varies at the optimal guide vane angle. Finally, pressure contours and velocity distributions in the distributor are discussed and compared.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.707-708
• /
• 2002

Catheters are used to measure translesional pressure gradients in the stenosed coronary arteries. Catheter insertions during coronary angioplasty cause flow obstructions. A narrowed flow cross section with catheter present effectively introduced a tighter stenosis than the enlarged residual stenoses after balloon angiplasty. In general, the form of stenoses are no uniform. Sometimes, these are occurred the irregularly eccentricity If the analyses are conducted for uniform stenosed artery, the results will be underestimated. Thus, in this study, three dimensional computer simulations are conducted to investigate the flow blockage effects due to the catheter insertion during the coronary angioplasty. The results for the eccentric stenosed artery are compared with those of the concentric stenosed artery.

• Economic and Environmental Geology
• /
• v.27 no.4
• /
• pp.397-409
• /
• 1994

The seemingly scattered plot of heat flow versus crustal thickness is explained by geodynamic processes and simple thermal relaxation in two contrasting tectonic elements. Elevated heat flow is characteristic of rift provinces where the crust is attenuated by stretching but also of orogenic belts where thrust tectonics thickens the crust and significantly enhances crustal heat production. With the progression of time, isostatic processes thin the thickened crust through uplift and erosion and thicken the rifted crust through subsidence and sedimentation. Heat flow relaxes to a value in equilibrium with background mantle heat flow.

• Journal of Welding and Joining
• /
• v.11 no.3
• /
• pp.34-47
• /
• 1993

Finite element models were developed for thermal and residual stress analysis for the specific welding problems. They were used to evaluate the effectiveness of the various welding heat input models, such as ramp heat input function and lumped pass models. Through the parametric studies, thermal-mechanical modeling sensitivity to the ramp function and lumping techniques was determined by comparing the predicted results with experimental data. The kinetics for residual stress formation during welding can be developed by iteration of various proposed mechanisms in the parametric study. A ramp heat input function was developed to gradually apply the heat flux with variable amplitude to the model. This model was used to avoid numerical convergence problems due to an instantaneous increase in temperature near the fusion zone. Additionally, it enables the model to include the effect of a moving arc in a two-dimensional plane. The ramp function takes into account the variation in the out of plane energy flow in a 2-D model as the arc approaches, travels across, and departs from each plane under investigation. A lumped pass model was developed to reduce the computation cost in the analysis of multipass welds. Several weld passes were assumed as one lumped pass in this model. Recommendations were provided about ramp lumping techniques and the optimum number of weld passes that can be combined into a single thermal input.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.5
• /
• pp.2092-2099
• /
• 2013

Through the data transfer race in industry since 1990s, the operational speed of optical disk drive(ODD) becomes commonly over 10,000 rpm. Such high speed operation inevitably causes the vibration, which is also the disturbances in the read-write process of pick-up servo-controller. Generally the vibration disturbance problem can be solved by the vibration isolation using the rubber mount and the increase of robustness of the pick-up servo-controller. Optical disk itself has not been targeted for the vibration reduction, because it is manufactured under the standardized format. In this paper we focused on the increase of critical speed of optical disk, that is, the improvement of dynamic characteristics, with the control of residual stresses which are come from the injection molding process. To do this, first, the residual stresses induced from the injection molding process are calculated using finite element method. The major design parameters of the process conditions are flow rate and melt temperature, which control the residual stresses in optical disk. Second, the critical speed of optical disk is calculated with modal analysis considering residual stress distributions. It was found out that the critical speed can be improved by the control of operational parameters in the injection molding process.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.16 no.3
• /
• pp.197-207
• /
• 2016

It is very important to maintain a constant chlorine concentration in the post chlorination process, which is the final step in the water treatment process (hereafter WTP) before servicing water to citizens. Even though a flow meter between the filtration basin and clear well must be installed for the post chlorination process, it is not easy to install owing to poor installation conditions. In such a case, a raw water flow meter has been used as an alternative and has led to dosage errors due to detention time. Therefore, the inlet flow to the clear well is estimated by a time series neural network for the plant without a measurement value, a new residual chlorine meter is installed in the inlet of the clear well to decrease the control period, and the proposed modeling and controller to analyze the chlorine concentration change in the well is a neuro fuzzy algorithm and cascade method. The proposed algorithm led to post chlorination and chlorination improvements of 1.75 times and 1.96 times respectively when it was applied to an operating WTP. As a result, a hygienically safer drinking water is supplied with preemptive response for the time delay and inherent characteristics of the disinfection process.

• Journal of the Korean GEO-environmental Society
• /
• v.18 no.2
• /
• pp.29-37
• /
• 2017

As the behavior of the debris flow due to the torrential rains in mountain is affected by shear strength and rheological properties of the fine fraction in the ground, the evaluation of both properties is necessary to estimate the behavior of the debris flow. The objective of this study is to evaluate the shear strength and rheological properties using the direct shear apparatus. The direct shear tests are conducted for two kinds of fine-grained soil specimens, which are in dry state and liquid limit state. From the direct shear tests, shear strengths are measured according to the normal stresses applied on the specimens to evaluate the cohesion and internal friction angle. In addition, reversal shear tests are performed for the fine-grained soil specimens in liquid limit state according to the shear rate to evaluate the residual shear strength. The results of direct shear tests show that the specimen at the liquid limit state has lower internal friction angle and higher cohesion compared to the dry stated, and the residual friction angle and cohesion at the residual state are lower than those at the peak state. In the result of reversal shear test, the residual shear strength is directly proportional to the shear rate and viscosity is calculated as $73.60Pa{\cdot}s$. This study demonstrates that the direct shear apparatus can be effectively used for the evaluation of the shear strength and rheological properties of the fine-grained soils related with the debris flow.

• 한국전산유체공학회:학술대회논문집
• /
• 2004.03a
• /
• pp.91-98
• /
• 2004

In two dimensional incompressible flows, a preconditioning technique called Hierarchical Iterative Procedure(HIP) has been implemented on a stabilized finite element formulation. The stabilization has been peformed by a modified residual method proposed by Illinca et. al.[3]. The stabilization which is necessary to escape from the LBB constraint renders an equal order formulation. In this paper, we increased the order of interpolation whithin an element up to cubic. The conjugate gradient squared(CGS) method is used for the outer iteration, and the HIP for the preconditioning for the incompressible Navier-Stokes equation. The hierarchical elements has been used to achieve a higher order accuracy in fluid flow analyses, but a proper efficient iterative procedure for higher order finite element formulation has not been available so far. The numerical results by the present HIP for the lid driven cavity flow showed the present procedure to be stable, very efficient and useful in flow analyses in conjunction with hierarchical elements.