• 해양환경안전학회지
• /
• 제22권4호
• /
• pp.344-353
• /
• 2016

황해연안 조위관측소 10 개 지점에서 2013년 11월 24일 밤부터 25일 오전까지 관측한 해수면, 해면기압, 바람, 유동 자료뿐만 아니라 일기도를 분석하여 이상조위편차의 발생 원인과 관측자료들 간의 상호상관성을 알아보았다. 이상조위편차란 최대조위편차와 최소조위편차가 나타나는 시간동안 두 편차간의 차를 의미한다. 영종도의 최대조위편차는 111 cm, 최소조위편차는 -65 cm로, 4시간 1분 동안 176 cm의 이상조위편차를 보여 10개 조위관측소 가운데 가장 크다. 반면 모슬포의 이상조위편차는 8시간 52분 동안 약 68 cm로 가장 작다. 이 같은 이상조위편차는 기압점프에 의한 기상해일이 아니라 저기압에 의한 기압배치의 영향으로 바람에 의해 발생한 것으로 확인되었다. 각 지점에서 이상조위편차에 의한 흐름은 연평균 낙조류 세기의 16 ~ 41 %로 무시할 수 없을 정도이다. 조위편차, 바람, 조류잔차의 상호상관관계로부터 저기압의 중심이 한반도 서쪽에 가까이 위치해 있을 때 인천에서 남풍계열의 바람에 의한 북향류가 해수면을 상승시켰고, 한반도 통과 후 북풍계열의 바람에 의해 남향류가 해수면을 하강시켰다.

• 한국해안·해양공학회논문집
• /
• 제25권2호
• /
• pp.103-111
• /
• 2013

방류 유무에 따른 유속, 잔차류 그리고 염분의 시공간적인 분포를 파악하기 위해서 영산강 하구둑에서 서쪽방향으로 7.5 km의 구간까지 방류 시와 미방류 시에 종단면의 유속, 수온 그리고 염분을 한 조석 주기 동안 1시간 간격으로 동시에 관측하였다. 미방류 시에 연구지역의 유속 형태는 창조지속 시간이 길고 낙조류가 강한 낙조우세 특성을 보인다. 방류 시에 표층 최대 유속은 최대 1.5 m/s의 제트류 형태로 방류되지만, 저층 유속은 미방류 시와 비교해보면 0.4 m/s로 크게 변하지 않는다. 방류 시의 수직 잔차류 분포는 담수의 영향으로 일반적인 하구에서 보이는 2층 흐름 구조를 가지는 반면에, 미방류 시에는 다층 흐름 구조가 나타난다. 일반적으로 방류로 인하여 하구둑 외측에서 강한 연직 혼합이 일어나는 것으로 알려져 있으나, 본 연구조사에서는 방류에 의해서 염분 성층이 발달하고, 표층과 저층간의 연직 혼합에 크게 기여하지 않는 것으로 나타났다. 이는 방류가 강하게 일어남에도 불구하고 하구둑 전면의 지형적 효과와 밀도 차에 의한 해수 흐름 특성에 의한 것으로 판단되며, 이를 통해 하구둑 방향의 물질수송은 수직 방향보다는 수평 방향으로 나타남을 알 수 있다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.1106-1110
• /
• 2003

The electrical characteristics of $A{\sim}C's$ ZnO varistors fabricated according to variable sintering condition, which sintering temperature is $l130^{\circ}C$ and speeds of pusher are A: 2mm/min, B: 4mm/min, C: 6 mm/min, respectively, were investigated. The varistor voltage of $A{\sim}C's$ ZnO varistors sintered at $1130^{\circ}C$ increased in order A < B $A{\sim}C's$ ZnO varistors exhibited below 2mA at rated voltage. Lightning impulse residual voltage of A's ZnO varistor suited standard characteristics, which is 3.85kV at 2.5kA, 4.4kV at 5kA and 5.16kV at 10kA. After multi lightning impulse residual voltage test of A's ZnO varistor exhibited good discharge characteristics which ZnO varistor reveals no evidence of puncture, flashover, cracking in visual examination. After high current impulse test of A's ZnO varistor exhibited good discharge characteristics, which variation rate of residual voltage is 0.4% before and after test, and revealed no evidence.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 추계학술대회 논문집 Vol.15
• /
• pp.552-556
• /
• 2002

The microstructure and electrical characteristics of A~C's ZnO varistors fabricated according to variable sintering condition, which sintering temperature is $1130^{\circ}C$ and speeds of pusher are A: 2mm/min, B: 4mm/min, C: 6mm/min, respectively, were investigated. In the microstructure, A~C's ZnO varist-ors fabricated variable sintering condition was consisted of ZnO grain(ZnO), spinel phase$(Zn_{2.33}Sb_{0.67}O_4)$ Bi-rich $phase(Bi_{2}O_{3})$, wholly. Varistor voltage of A~C's ZnO varistors sintered at $1130^{\circ}C$ increased in order A < B < C's ZnO varistors. C's ZnO varistor exhibited good characteristics that nonlinear exponent is 31.70. Leakage current of A~C's ZnO varistors exhibited below 2mA at rated voltage. Lightning impulse residual voltage of A's ZnO varistor suited standard characteristics, which is 3.85kV at 2.5kA, 4.4kV at 5kA and 5.16kV at 10kA. After multi lightning impulse residual voltage test of A's ZnO varistor exhibited good discharge characteristics which ZnO varistor reveals no evidence of puncture, flashover, cracking in visual examination. After high current impulse test of A's ZnO varistor exhibited good discharge characteristics, which variation rate of residual voltage is 0.4% before and after test, and revealed no evidence.

• 한국환경과학회지
• /
• 제11권1호
• /
• pp.41-56
• /
• 2002

In order to estimate the quantitative roles of the tide induced residual currents, density currents and wind driven currents on the residual currents in Kwangynag Bay Korea, numerical experiments with a diagnostic multi-level model were carried out. Density currents were calculated from the temperature and salinity data observed in January, May, August and November 1998. Anti-clockwise circulations are formed at the western inner part of the bay, the location from the east of Myodo Is. to the south of POSCO Co. and the place between Yeosu peninsula and Namhae Is. from the calculation results of the tide induced residual currents. Velocities of the density currents are less than 3cm/s at the western inner part of the bay and about 5cm/s at the southern entrance of the bay. Density currents get strong in summer and weak in autumn. Wind driven currents at the surface layer flow in the directions of the given winds which are the daily mean winds when the temperature and salinity observations are carried out. In the middle and lower layers, however the wind driven currents flow in the opposite direction to the surface currents as supplementary currents. The surface wind driven currents are greater than the tide induced residual currents or the density currents. The calculated residual currents including the tide induced residual currents, density currents and wind driven currents agree with the results of the current observations approximately. In the Bay, the wind driven currents affect on the residual currents greatestly and tide induced residual currents and density currents do in the second place and the third place.

• Journal of Advanced Marine Engineering and Technology
• /
• 제25권3호
• /
• pp.631-635
• /
• 2001

The major problems associated with the manufacturing processes of the microaccelerometer based on the tunneling current concept is the residual stress. This paper deals with finite element analysis of residual stress causing pop up phenomenon which are induced in micromachining processes for a microaccelerometers sensor using silicon on insulator(SOI) wafer. After heating the tunnel gap up to $100^{\circ}C$and get it through cooling process and the additional beam up to $80^{\circ}C$get it through the cooling process. We learn the residual stress of each shape and compare the results with each other, after heating the tunnel gap up to $400^{\circ}Cduring$ the Pt deposition process. The equivalent stresses produced during the heating process of focused ion beam(FIB) cut was also to be about $0.02~0.25Pa/^{\circ}C$and cooling process the gradient of residual stresses of about $8.4\{times}10^2Pa/{\mu}m$ still at cantilever beam and connected part of paddle. We want to seek after the real cause of this pop up phenomenon and diminish this by change manufacturing processes of microaccelerometer sensors.

• 한국안전학회지
• /
• 제19권4호
• /
• pp.20-24
• /
• 2004

Antifatigue failure technology take an important the part of current industries. Currently, the shot peening is used for removing the defect from the surface of steel and improving the fatigue strength on surface. Therefore in this paper the effect of compressive residual stress by shot peening on fatigue crack growth characteristics in stress ratio(R=0.1, 0.3, 0.6)was investigated with considering fracture mechanics. There is difference between shot peening specimen and unpeening specimen. Fatigue crack growth rate of shot peening specimen was lower than that of unpeening specimen. Fatigue lift shows more improvement in the shot peening material than in the unpeening material. And compressive residual stress of surface on the shot peening processed operate resistance force of fatigue crack propagation. That is the constrained force about plasticity deformation was strengthened by resultant stress, which resulted from plasticity deformation and compressive residual stress in the process of fatigue crack propagation.

• 소성∙가공
• /
• 제25권1호
• /
• pp.61-66
• /
• 2016

In the current study, we present a new model for the prediction of the strip profile and the residual stresses. This new approach is an analytical model that predicts the residual stresses from the effect of post-deformation. Since the residual stress cannot exceed the yield strength of the material, post-yielding may possibly occur in the post-deformation zone prior to the strip reaching the steady-state zone. The prediction accuracy of the proposed model is examined through comparison with the predictions from 3-D finite element (FE) simulations.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2006년도 정기 학술대회 논문집
• /
• pp.490-495
• /
• 2006

The analysis method proposed by PCA is widely used in calculating the column shortening of reinforced and composite columns of a tall building. However, residual creep factor which relates creep strain of reinforced concrete to creep strain of plain concrete is based on Rate of Creep Method (RCM) which has theoretical defects and is considered obsolete. In this paper, a new equation for the residual creep factor based on Age-adjusted Effective Modulus Method (AEMM) which is considered exact and better than RCM is proposed. The residual creep factor by RCM is found to be higher than one by AEMM, which means current PCA method overestimates the shortening of a reinforced concrete column. By using the residual creep factor by AEMM, more exact column shortening of a tall building can be obtainable with a simple modification to PCA method.

• Structural Engineering and Mechanics
• /
• 제39권2호
• /
• pp.287-301
• /
• 2011

This paper is focused on the residual capacity of steel columns, as a damage criterion. Load-Impulse (P-I) diagrams are frequently used for analysis, design, or assessment of blast resistant structures. The residual load carrying capacity of a simply supported steel column was derived as a damage criterion based on a SDOF computational approach. Dimensionless P-I diagrams were generated numerically with this quantitative damage criterion. These numerical P-I diagrams were used to show that traditional constant ductility ratios adopted as damage criteria are not appropriate for either the design or damage assessment of blast resistant steel columns, and that the current approach could be a much more appropriate alternative.