• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.11
• /
• pp.776-781
• /
• 2007

Optimized capacity of equipments are essential for energy saving and low cost construction and operation. So we must use proper design data for HVAC system design. We investigated for architectural data, equipment capacity, cooling and heating load design criteria of 52 office buildings. Following research results were obtained by carrying out each task. Office building effective area rate is 63%. The average building cooling load of South Korea is $140W/m^2$ and average heating loads in Seoul and Pusan area are $120{\sim}130W/m^2$ and $70{\sim}80W/m^2$. We also analysised HVAC design criteria. Person ratio in effective building area is $0.2person/m^2$, sensitive and latent heat loads of a person are 60W and 65W, light and equipment loads of office buildings are $25W/m^2$ and $20W/m^2$.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.26 no.2
• /
• pp.86-90
• /
• 2014

It is important to select an optimal capacity for equipment, because the initial cost of new and renewable energy system is more expensive than that of exiting system. An optimal equipment and enhanced rate of operation can be selected, to analyze the cooling and heating load of buildings. In this study, seawater heat pump system in the Jeju area will be applied, by the heat source equipment of district heating. The loads of buildings are analyzed from existing researches, to select optimal capacity of equipment. Also, an optimal rate of building use will be set up, from a combination of buildings.

• Journal of Korea Multimedia Society
• /
• v.24 no.2
• /
• pp.199-207
• /
• 2021

It is very important to support real-time on the inspection equipment based on Windows. In particular, in the system using MIL-STD-1553B communication, which is widely used in military weapon systems, real-time is required for inspection equipment that uses mostly platforms based on Windows such as Industrial PCs. However, in order to use a complete real-time operating system such as VxWorks, the purchase cost is expensive and the implementation is complicated on the system, so it is not suitable for inspection equipment that requires simple functions to just check go or no-go. Therefore, in this paper, a Real-Time implanted Kernel(RTiK) in the Windows kernel is implanted in order to improve these defects, and real-time performance is implemented for periodically MIL-STD-1553B communication by Deferred Procedure Call(DPC) of Windows. Also, it was verified that the period of up to 2ms was guaranteed with a RDTSC into the EDX:EAX registers for measuring the periodicity.

• Journal of KIBIM
• /
• v.11 no.2
• /
• pp.24-32
• /
• 2021

Recently, starting with smart construction research, interest in technology that automates construction site management using artificial intelligence technology is increasing. In order to automate construction site management, it is necessary to recognize objects such as construction equipment or workers, and automatically analyze the relationship between them. For example, if the relationship between workers and construction equipment at a construction site can be known, various use cases of site management such as work productivity, equipment operation status monitoring, and safety management can be implemented. This study derives a real-time object detection platform architecture that is required when performing construction site management using deep learning technology, which has recently been increasingly used. To this end, deep learning models that support real-time object detection are investigated and analyzed. Based on this, a deep learning model development process required for real-time construction site object detection is defined. Based on the defined process, a prototype that learns and detects construction site objects is developed, and then platform development considerations and architecture are derived from the results.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.39 no.1
• /
• pp.84-95
• /
• 2011

The purpose of this study is to increase the usage of satisfaction of outdoor exercise equipment installed at parks when plans and designs are made for renovation or formation of parks. In order to do so, the study surveyed and analyzed the usage satisfaction of 150 men and women who use outdoor exercise equipment in neighborhood parks located in Dongtan New Town. There were four factors that affect the variables of usage satisfaction. They can be defined as the main facility factor, awning factor, maintenance factor, and additional facility factor. From the result regression analysis of the total satisfaction rate and the factors, the main facility factor was the most influential of the variables. This could indicate that the facility factor affects the satisfactory rate of outdoor exercise equipment. This research is done only with the examples of neighborhood parks, so it limits the possibility of analysis of seasonal use. It is necessary to conduct analysis research of parks which installed many outdoor exercise equipment, such as a vest-pocket park, children's garden, and pedestrian/urban/metropolitan neighborhood parks.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.6
• /
• pp.1059-1068
• /
• 2016

The current operation method for the AVC (Automatic Vehicle Classification) equipment does not generate vehicle speed, traffic volume and vehicle type information when part of the sensors has failed. Inefficiency of current methods would not use the collected data from the normal sensor. In this study was conducted research on the calculating method at the traffic volume and vehicle speed in the sensor failure AVC equipment. The failure situation of the sensor was classified into 4 types. Calculating the traffic volume and vehicle speed information for each type, and accuracy of these informations were analyzed. Analysis results, traffic volume was possible to calculate a highly accurate value (accuracy: 100%, 98%, 97%). In the case of speed, the accuracy of the calculated speed value reaches a level that can be accepted sufficiently (RMSE value is less than 16.8). So, using the methodology proposed in this study are expected to be able to increase the operational efficiency of the AVC equipment.

• Journal of the Korea Safety Management & Science
• /
• v.17 no.2
• /
• pp.147-152
• /
• 2015

Through the inspector's real name to improve the quality of inspection is to show the design Radiological examination pursuant to the Ordinance of the Ministry of Health and Welfare for patient safety in the Image. However, the use of existing and in EMR, equipment within the handwriting input, the individual initial use has a problem. In this study, increasing the stability of the patient and the precise inspection, In order to increase the efficiency and convenience than the real-name system for quality control inspectors of medical equipment, Using the EMR and PACS developed and applied to evaluate the usefulness of automatic enrollment. Enter your information in the EMR, which was developed markers that inspectors use to compare the before and after images PACS satisfaction. Convenience than using traditional, consistency, the entry of the missing were higher as a statistically significant difference. A test strip automatic enrollment programs are developed in this study. You can increase the stability of the patient by checking the image to show the real tester, we expect the quality of care would be improved.

• Journal of Navigation and Port Research
• /
• v.45 no.2
• /
• pp.61-68
• /
• 2021

Logistics movement using ships has been used for many centuries, but maritime accidents are still difficult to predict and they occur on a large scale. The International Maritime Organization (IMO) made it mandatory to install Electronic Chart Display and Information System (ECDIS) for safe seas, but S-57 standards applied to equipment were not updated over 30 years. In addition, it is difficult to keep the equipment up-to-date and revise standards as ships move around the world. In consideration of the limitations of S-57, the IHO developed the new standard as S-100 rather than an update of the S-57. In this study, the previously developed S-100 tool and S/W were configured as one platform and applied to the S-100 ECDIS. The platform conducts as the S-100 cycle and ecosystem from the creation of standards to release and practical use in ships. The hydrographic information standard is machine-readable as defined in S-100, and it has been validated that the latest standard can be applied using the Plug and Play (PnP) function without software system updates. It is expected that international organization such as the International Hydrographic Office (IHO) and the International Association of Marine Aids to Navigation and Lighthouse Authorities (IALA) shall develop and release standards and mariners can easily apply the latest standards to equipment through the machine-readable platform.

• Journal of Applied Reliability
• /
• v.15 no.3
• /
• pp.181-191
• /
• 2015

Change in labor time is affecting occupational safety and health. Recently reduction in labor time brought innovational operation method, investment in plant and equipment, and flexible labor time in some companies, thereby affecting working conditions for labourers. However, working conditions for some vulnerable social groups have deteriorated. As a result, they are becoming more exposed to risk factors such as injury and emotional stress. In this study we use 2014 KWCS data in order to find the social and demographic characteristics in Korean working conditions. To this end, we use exploratory data analysis approach to find the relationship between some of the important variables in the KWCS data. We also use Press-State-Response model to find which group of people are vulnerable to Press and State. We find that women, people over age 50 and business owners are more vulnerable to Press and State than men, people below age 50 and wage workers.

• Journal of Sensor Science and Technology
• /
• v.32 no.3
• /
• pp.180-186
• /
• 2023

Test devices can perform various functions, such as research on detection targets, sensors that detect detection targets, combined products containing sensors, and certification for the launch of combined products. However, the scope of use of test devices is limited because they perform only a single role or could only serve a particular purpose in the past. Therefore, studies on test devices that can perform various functions, such as research on detection targets, sensors that detect detection targets, combined products containing sensors, and certification for the release of combined products are necessary. Accordingly, this study proposes a test device that can increase the scope of use in the technical field of electric fires. In addition, we examine various outcomes of the proposed test device.