• Current Photovoltaic Research
• /
• 제4권2호
• /
• pp.59-63
• /
• 2016

A key point of a soldering process for photovoltaic (PV) modules is to increase an adhesive strength leading a low resistivity between ribbon and cell. In this study, we intended to optimize a heating condition for the soldering process and characterize the soldered joint via physical and chemical analysis methods. For the purpose, the heating conditions were adjusted by IR lamp power, heating time and hot plate temperature for preheating a cell. Since then the peel test for the ribbon and cell was conducted, consequently the peel strength data shows that there is some optimum soldering condition. In here, we observed that the peel strength was modified by increasing the heating condition. Such a soldering property is affected by a various factors of which the soldered joint, flux and bus bar of the cell are changed on the heating condition. Therefore, we tried to reveal causes determining the soldering property through analyzing the soldered interface.

• Journal of Welding and Joining
• /
• 제22권6호
• /
• pp.19-24
• /
• 2004

The laser welding and its analysis of thin-sheet carbon steels were carried out with high power $CO_{2}$ laser. The main factor of weld quality of laser welding is gap and edge quality. This work was preformed to focus on the gap tolerance problem during laser welding. First, bead on plate welding of thin sheet was examined to investigate the effect of laser welding variables, and to obtain optimum welding condition. Butt welding was also carried out to show the effect of gap on the laser weldability of thin sheet. In order to investigate the effect of gap on formability of welded thin sheet, LDH test was caried out. At high welding speed, the partial penetration was obtained by low heat input. Otherwise, porosity was formed in the bead at low weld speed because of too much heat input. The optimum welding condition of welding was derived from bead width, penetration and hardness property. The maximum gap tolerance on laser welding was observed to be about 0.2mm. This gap size has good relationship with beam size of laser spot(about 0.3mm). The formability of welded sheet was about $80{\%}$ value of base metal and the gap size has not affected on the formability, although weld quality is dependent on the gap size.

• 한국식품영양과학회지
• /
• 제35권10호
• /
• pp.1420-1426
• /
• 2006

여러 유도체 형태로 존재하는 대두 isoflavone을 산 가수 분해 방법 및 시간을 달리하면서 isoflavone 배당체의 aglycone으로의 전환율 및 aglycone의 분해여부를 실험하였다. 산 가수분해시 가열처리 조건을 $105^{\circ}C$ 항온기, $95^{\circ}C$ 수욕조, $120^{\circ}C$ heating block 및 hot plate로 달리한 결과 환류냉각장치를 이용하고 heating block에서 가수분해시키는 방법이 가장 적절한 가수분해 방법인 것으로 나타났다. 가수분해 시간 동안 aglycone의 안정성을 검토한 결과 적정 가수분해 시간인 60분 동안에는 genistein, daidzein 및 glycitein 모두 큰 함량변화가 없었다. 가수분해하는 시료의 양과 산의 비율은 시료 $10\sim30mg$당 1 N HCl 용액 1 mL의 비율이 적정하였다. 이상의 결과로부터 정량법은 0.5 g의 대두 시료에 1 N HCl용액 15 mL를 첨가하고 $120^{\circ}C$의 heating block에서 60분간 가수분해시킨 후 methanol로 50 mL로 정용하고 HPLC로 분석하도록 확립하였다. 이에 따라 대두 가공부산물의 iosflavone을 분석한 결과 착유 및 착유 후 hexane 제거를 위한 열처리 공정에서 isoflavone의 손실은 적은 것으로 나타났다.

• 셀메드
• /
• 제9권1호
• /
• pp.1.1-1.13
• /
• 2019

Background: Contents of bioactive substances extractable from different parts of terrestrial plants vary enormously. Aim: To ascertain that parts of Withania somnifera other than its roots can also be used for prevention and cure of unavoidable stress triggered central hypersensitivity to pain. Material and Methods: Groups of male or female mice treated either with Withania somnifera extracts or with metformin, aspirin, imipramine, diazepam and niacin for 11 consecutive days were subjected to "foot-shock stress-induced hyperthermia" and "hot plate" tests on the 1st, 5th, 7th, and 10th days of the experiments. On the 11th day, they were subjected to tail suspension test and on 12th day pentobarbital hypnosis test. Results: Except for diazepam and imipramine, protective effects of all other tested drugs as well as of the Withania somnifera extracts against stress-induced central hypersensitivity to pain were accompanied by their preventive effects against foot-shock stress-induced body weight losses. All observed stress response suppressing effects of all test agents increased with increasing numbers of treatment days. However, mean duration of pentobarbital-induced sleep was shorter in the extracts treated groups and longer in the diazepam treated ones only. Conclusions: Reported observations reveal that pharmacological activity profile of Withania somnifera extracts in male and female mice are almost identical, and are not like those of several drugs currently often prescribed for the treatment of diabetes-associated comorbidities. Withanolides are not the only extractable bioactive constituents of Withania somnifera. The described bioassay system is well suited for pharmacological standardization of diverse types of Withania somnifera extracts.

• 한국조리학회지
• /
• 제19권3호
• /
• pp.73-86
• /
• 2013

본 연구에서는 우리나라에서 많이 재배되고 섭취량이 많은 들깻잎을 생면에 첨가를 하여 식품으로서의 이용가치와 최적의 생면 레시피를 도출하고자 열풍건조 들깻잎을 제조하여 밀가루 대비 0%, 3%, 6%, 9%, 12%를 각각 첨가하였다. 반죽의 수분은 0%첨가한 대조군이 34.41%로 가장 높게 나타냈으며, pH는 12%를 첨가한 반죽이 5.59로 가장 낮은 수치를 나타냈다. 반죽의 L값과 a값은 0% 첨가군이 가장 큰 값을 보였으며, b값은 첨가량이 증가할수록 감소하였다. 반죽의 WRC 분석결과는 첨가량이 많아질수록 수분흡수력이 증가하였다. 생면의 수분함량은 0%첨가한 대조군이 가장 낮았으며, pH는 대조군이 가장 높게 나타났다. 생면의 L, a, b값은 0% 첨가군이 각각 가장 높은 값을 나타냈다. 중량과 부피는 0% 첨가군이 가장 큰 값을 나타났고, 탁도의 경우 열풍건조한 들깻잎의 첨가량이 증가 할수록 탁도가 증가한 경향을 보였다. 경도(Hardness)와 응집성(Cohesiveness)은 는 0% 첨가군이 가장 낮게 나타났고, 탄력성(Springiness)은 열풍건조 들깻잎의 첨가량이 증가 할수록 감소하는 경향을 보였으며, 생면의 미생물 변화는 저장 2일과 3일째에는 시료의 첨가량에 따라서 월등히 감소하는 경향을 보였다. 관능검사의 결과에서 외관(Appearance), 향(Flavor), 색(Color), 맛(Taste), 조직감(Texture) 모든 항목에서 6% 첨가군이 가장 높았다. 전체적인 기호도(Overall acceptability) 역시 6% 첨가군이 7.20로 가장 높았고, 12% 첨가가 3.27로 가장 낮게 나타났다. 이와 같은 결과를 종합허여 볼 때 열풍건조한 깻잎 분말을 첨가를 하여 생면을 제조시에는 저장성과 관련된 부분에서는 첨가량이 많아질수록 미생물 억제작용이 증가하나, 관능적 측면에서는 6% 첨가시에 가장 우수한 것으로 나타났다.

• Nuclear Engineering and Technology
• /
• 제52권7호
• /
• pp.1517-1523
• /
• 2020

The widely used medical isotope technetium-99 m (^99mTc) is a daughter of Molybdenum-99 (⁹⁹Mo), which is mainly produced using dedicated research reactors from the nuclear fission of uranium-235 (²³⁵U). ^99mTc has been used for several decades, which covers about 80% of the all the nuclear diagnostics procedures. Recently, the instability of the supply has become an important topic throughout the international radioisotope communities. The aging of major ⁹⁹Mo production reactors has also caused frequent shutdowns. It has triggered movements to establish new research reactors for ⁹⁹Mo production, as well as the development of various ⁹⁹Mo production technologies. In this context, a new research reactor project was launched in 2012 in Korea. At the same time, the development of fission-based ⁹⁹Mo production process was initiated by Korea Atomic Energy Research Institute (KAERI) in 2012 in order to be implemented by the new research reactor. The KAERI process is based on the caustic dissolution of plate-type LEU (low enriched uranium) dispersion targets, followed by the separation and purification using a series of columns. The development of proper waste treatment technologies for the gaseous, liquid, and solid radioactive wastes also took place. The first stage of this process development was completed in 2018. In this paper, the results of the hot test production of fission ⁹⁹Mo using HANARO, KAERI's 30 MW research reactor, was described.

• 한국의학물리학회:학술대회논문집
• /
• 한국의학물리학회 2002년도 Proceedings
• /
• pp.418-421
• /
• 2002

Fundamental study on quasi-monochromatic parallel radiography using a polycapillary plate and a plane-focus x-ray tube is described. The x-ray generator consists of a negative high-voltage power supply, a filament (hot cathode) power supply, and an x-ray tube. The negative high-voltage is applied to the cathode electrode, and the transmission type target (anode) is connected to the ground potential. The maximum voltage and current of the power supply were -100 kV (peak value) and 3.0 mA, respectively. In this experiment, the tube voltage was regulated from 20 to 25 kV, and the tube current was regulated by the filament temperature and ranged from 1.0 to 3.0 mA. The exposure time is controlled in order to obtain optimum film density, and the focal spot diameter was about 10 mm. The polycapillary plate is J5022-21 made by Hamamatsu Photonics Inc., and the outside and effective diameters are 87 and 77 mm, respectively. The thickness and the hole diameter of the polycapillary are 1.0 mm and 25 ${\mu}$m, respectively. The x-rays from the tube are formed into parallel beam by the polycapillary, and the radiogram is taken using an industrial x-ray film of Fuji IX 100 without using a screen. In the measurement of image resolution, we employed three brass spacers of 2, 30, and 60 mm in height. By the test chart, the resolution fell according to increases in the spacer height without using a polycapillary. In contrast, the resolution slightly fell with corresponding increases in the height by the polycapillary. In angiography, fine blood vessels of about 100 ${\mu}$m are clearly visible.

• Advances in Traditional Medicine
• /
• 제8권3호
• /
• pp.243-251
• /
• 2008

The effect of alcoholic extracts of Costus specious (Family: Zingiberaceae) was evaluated in experimental models of pain and inflammation. Oral administration of 100, 200 and 300 mg/kg of C. specious extracts were used for the above study. Crude extracts of C. specious (300 mg/kg dose) showed maximum time needed for the response against thermal stimuli ($7.242\;{\pm}\;0.532\;s$) which is comparable to diclofenac sodium ($8.471\;{\pm}\;0.25\;s$) in the hot plate test. The MPH (Maximum Possible Analgesia) has been found to be 14.285 for 300 mg/kg dose of the crude extract while the MPH for diclofenac was 15.857 after 60 min of administration in the hot tail-flick method. The crude extract at 300 and 200 mg/kg doses showed significant reduction in acetic acid induced writhings in mice with a maximum effect of 59.661% reduction at 300 mg/kg dose which is comparable to standard diclofenac sodium (73.4%). Alcoholic extract of C. specious showed significant inhibition in serotonin and egg albumin induced hind paw oedema in rats at 100, 200 and 300 mg/kg of the crude extracts respectively (Serotonin induced edema 44.22; 53.75; 58.51%; egg albumin induced edema - 41.317; 53.892; 59.880% inhibition after 4 h respectively). The antiinflammatory effects showed by the extract were comparable to that of standard indomethacin 5 mg/kg (Serotonin induced edema 77.56%; egg albumin induced edema 77.844% inhibition after 4 h). These results suggest that the extract possesses both the anti-inflammatory and analgesic activity on mice and rat model.

• Advances in Traditional Medicine
• /
• 제7권5호
• /
• pp.485-493
• /
• 2008

The present study was carried out to elucidate the potential of, chloroform extract of Pandanus (P.) fascicularis Lamk (Family-Pandanaceae) leaves on antinociceptive, behavioral study and anti-inflammatory effects using various animal models The dried, powdered leaves of, P. fascicularis were extracted successively with petroleum ether ($60\;-\;80^{\circ}C$) and chloroform in soxhlet apparatus. The chloroform extract (yield 21.6% w/w with respected to dry powdered plant material) was selected for all experimental procedure. Two models were employed to investigate the effects on nociception, the tail immersion and hot plate method in Swiss albino mice and anti inflammatory effect were investigated by employing the carrageenan induced rat paw edema test in. adult Wister albino rats. Behavioral study was investigated by elevated plus maze method in Swiss albino mice. Results were revealed that the PFCE was found significant antinociceptive effect (P < 0.001) at the dose levels of 100, 200 and 400 mg/kg, orally in mice and produced remarkable antiinflammatory effect (P < 0.001) at the same dose levels used in the rats. Behavioral study of the PFCE has no significant anxiolysis effect when used orally. It concludes that, PFCE possessed remarkable antinociceptive effect and anti-inflammatory effect but no anxiolytic effect on animal models.

• Natural Product Sciences
• /
• 제9권2호
• /
• pp.97-101
• /
• 2003

This study was undertaken to evaluate the antinociceptive and antiinflammatory effects of the heartwood extract of Rhus verniciflua (Anacardiaceae) and the two major components, sulfuretin and fustin. The MeOH extract, its EtOAc-soluble portion and sulfuretin showed significant antinociceptive activity in writhing and hot plate test assays and antiinflammaory effects in carrageenan-induced hind paw edema in rats. In particular, treatment of sulfuretin with 10 mg/kg dose (i.p.) reduced writhing frequency by 48.0% (p<0.01) compared to that of a control group. Further, the treatment of sulfuretin (5, 10 mg/kg, i.p.) for 7 days prevented the carrageenan-induced hind paw edema significantly (p<0.01). The antiinflammatory effect of sulfuretin was also confirmed by microscopic observation of mast cell numbers in muscle. In addition, sulfuretin suppressed the cyclooxygenase- 2 (COX-2) activity $(IC_{50}\;=\;28.7\;{\mu}M)$ in lipopolysaccharide-activated macrophage cells. This result indicates that the inhibitory effect of sulfuretin on COX-2 may be one of the antinociceptive/antiinflammatory mechanism.