• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.892-897
• /
• 2000

In this study, tap wear was analyzed not only to predict the tap life time but also to propose an improved tap design. Because rake angle and thread relief of tap are the significant factors in geometry of tap, these two factors were picked as the experiment variables. The experiment was conducted with six types of tap which have 6$^{\circ}$ , 8$^{\circ}$ and 12$^{\circ}$ of rake angles with 0,08mm and 0.14 mm of thread relief. From the measured cutting force, it could be known that cutting torque was low at the large the rake thread relief and tool life was long as rake angle became large. Eventually, tool life is longest when rake angle is 12$^{\circ}$ and the with 0.08mm thread relief. Aand the width of crater wear and that of flank wear were measured when a tapping torque was 20 [$kg_f$-mm] . Most of the measured values were above the width of tool wear[$V_B$=O.O3m], which means that tool life is over.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.685-690
• /
• 2000

In this study relationship between relief angles and chatter vibration in turning was examined by using the direct cutting test, in which the cutting depth of a tapered workpiece is varied continuously and the limiting depth of cut is measured at the time when chatter occurs. Test results reveal that 1) limiting depth of cut increases is proportion to side relief angles between 0$^{\circ}$ and 3$^{\circ}$, 2) limiting depth of cut does not show any evident change in spite of side relief angle increased from 3$^{\circ}$ to 12$^{\circ}$, 3) also limiting depth of cut does not change despite front angle change from 0$^{\circ}$ to 12$^{\circ}$.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.10a
• /
• pp.393-398
• /
• 2001

The technique of high speed machining is widely studied in machining fields, because the high efficiency and accuracy in machining can be obtained in high speed machining. Unfortunately the development of tool for high speed machining in not close behind that of machine tool. In this study, several types flat endmill is prepared for obtaining data according to tool shape. Especially, we concentrated in helix angle, number of cutting edge, rake angle and relief angle. Machinability is measured by cutting force, tool life, tool wear, chip shape and surface roughness according to cutting length. 3-axis cutting forces are acquired from the invented tool dynamometer for high speed machining. Particularly, we found out that the axial cutting force waveform has a good relation with tool wear features. By above results, it is suggested the endmill tool with $45^{\circ}$ helix angle, 6 cutting edge, $-15^{\circ}$ rake angle and $12^{\circ}$ relief angle be suitable for high speed machining

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.1
• /
• pp.88-94
• /
• 2012

An axle drive shaft with double joint shaft, cross kit and yoke has an important role by transferring power and changing steering angle between axle and wheel in power train system. It has been used widely in the heavy machinery requiring a high reliability in the power train system. At fatigue failures of the axle drive shaft with the long span, a relatively high stress concentration at a snap ring groove on the drive shaft brings to significant fatigue damages under repeated loading condition. As Peterson's suggestions on this study, a relief groove in the vicinity of the snap ring groove is applied by decreasing the stress concentration and improving the fatigue life of axle drive shaft. By using FEM analysis, the decreasing effect of the stress concentration and extended fatigue life are due to the change of design parameters related with size and location of the relief groove. The relief groove with the design parameters such as d/b=2.0 and r/h=1.2 enables to decrease the stress concentration of 22.3% and increase the fatigue life more than 3 times by comparing with no relief groove application.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.9
• /
• pp.1520-1530
• /
• 1997

Machining pressed compacts of ceramic and WC-Co materials can be the most cost effective way of forming the bodies prior to sintering when the required number of pieces is small. In this study, in order to clarify the machinability for turning, the $Si_3N_4$ and the WC-Co green compacts unsintered were machined under different cutting conditions with various tools. Absorbing chips by vacuum hose decreases tool wear. The tool wear becomes larger in the order of the ceramic, CBN and cemented carbide tools in machining the $Si_3N_4$ green compacts. In machining the WC-Co green compacts, the tool wear becomes larger in the order of the ceramic, cemented carbide and CBN tools. The land of cutting edge does not affect tool wear. When machining with cemented carbide tool, the tool wear i equal cutting length is nearly identical in spite of the increase of cutting spee, and the roughness of machined surface was the best in the cutting speed of 90 m/min. The tool wear decreases with the increase of rake angle and relief angle and with the decrease of nose radius. The machined surfaces become worse with the increase of feed rate and depth of cut, and with the decrease of rake angle and relief angle. The tool wear is not affected by the feed and depth of cut.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.30 no.1
• /
• pp.21-30
• /
• 2012

When two bands have different look angle in a space-borne camera system, the registration between two bands is required. The registration cannot be modeled with constant parameters because of dynamic of platform and parallax effect. The parallax effect is caused by terrain relief, hence it causes local distortion between two bands. Therefore, the terrain relief correction in order to reduce the parallax effect is required for better registration result, especially for high resolution image data. Such terrain relief correction also can be applied to image data acquired from multiple detectors with different look angle within a band, which is a one of commonly used configuration for a wider swath in space-borne camera system, in order to reduce the distortion between detectors. The RFM is a popular abstract model in remote sensing field, which gives us the relationship between the image plane and geodetic coordinate system. Therefore, we propose a terrain relief correction method based on the RFM. The experiment showed very promising result.

• Transactions of Materials Processing
• /
• v.8 no.1
• /
• pp.14-21
• /
• 1999

Trapezoid cups and square ones have been deep-drawn to 45mm in depth. Displacements and strains have been analysed by FEM and experiment. Strains and effective strains in the corner flanges of trapezoid cups have been compared with those in square cups. The results have shown that because of shear strains on the corner flange, it is necessary to adopt effective strain for comparing strains, mean vale of effective strains in the corner flange with a corner angle of 72 degrees is narly equal to those with a corner angle of a right angle and mean value of effective strains with a corner angle of 102 degrees is smaller than those with a corner angle of a right angle.

• Journal of Yeungnam Medical Science
• /
• v.4 no.1
• /
• pp.151-156
• /
• 1987

A 25 year and 7 month old man patient who had Angle's classII division 2 malocclusion combined with anterior crowding of upper & lower part was treated by bioprogressive mechanism. After setting our objectives through the use of V.T.O., we programmed a sequence of mechanics. The possible objectives of treatment in the classII division 2 malocclusion can be listed as follows. 1) Relief of crowding & irregularities. 2) Relief of anterior gingival trauma & correction of interincisal inclination. 3) Correction of buccal segment relationship. We'd applied the classII intermaxillary elastics, Quad helix, utility arch wire and sectional arch wire in order to achieve anticipated objectives. As compared with pre & post treatment cephalogram, the result accomplished by this mechanics showed to us that interincisal angle was improved and favorable molar relationship was achieved.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.24 no.5
• /
• pp.868-873
• /
• 1987

Holographic diffraction gratings which are the core element of the optical instruments such as a spectrophotometer have been fabricated using the photoresist as a recording material. A 488nm line from an argon laser is used in making the gratings. Transmission type surface-relief phase grating and reflection type which is fabsricated by coating the aluminum on the transmission type with thickness 2000\ulcornerare fabricated, the spatical frequency of which are 1200 lines/mm. Diffraction efficiency, scattered light and wave-front aberratin are measured to test the performance of the developed gratings. A marimum diffraction efficiency is given when light is incident at the Bragg angle. Theoretical efficiency is about 80%, but measured efficiency of the transmission type and reflection type is 50% and 45%, respectively.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.947-950
• /
• 1998

Geological structures such as fault and fracture patterns provide important information about preliminary exploration of mineralized areas and geological characterization. We apply a filtering method taking the sun's azimuth angle into account to a shaded relief image derived from a digital elevation model (DEM), by which even linear edges extending parallel to the sun direction can be effectively extracted. Then, Generalized Hough tranform is applied to extract lineanments which correspond to fault and fracture patterns.