• Journal of Energy Engineering
• /
• v.23 no.1
• /
• pp.81-89
• /
• 2014

The purpose of this study is to obtain low-emission and high-efficiency in LPG engine with hydrogen enrichment. The objective of this paper is to clarify the effects of hydrogen enrichment in LPG fuelled engine on exhaust emission, thermal efficiency and performance. The compression ratio of 8 was selected to avoid abnormal combustion. To maintain equal heating value of fuel blend, the amount of LPG was decreased as hydrogen was gradually added. The relative air-fuel ratio was increased from 0.76 to 1.5, and the ignition timing was controlled to be at minimum spark advance for best torque (MBT).

• Geomechanics and Engineering
• /
• v.6 no.5
• /
• pp.487-502
• /
• 2014

A three dimensional finite element model was used to simulate rapid impact compaction (RIC) in loose granular soils using ABAQUS software for one impact point. The behavior of soil under impact loading was expressed using a cap-plasticity model. Numerical modeling was done for a site in Assalouyeh petrochemical complex in southern Iran to verify the results. In-situ settlements per blow were compared to those in the numerical model. Measurements of improvement by depth were obtained from the in-situ standard penetration, plate loading, and large density tests and were compared with the numerical model results. Contours of the equal relative density clearly showed the efficiency of RIC laterally and at depth. Plastic volumetric strains below the anvil and the effect of RIC set indicated that a set of 10 mm can be considered to be a threshold value for soil improvement using this method. The results showed that RIC strongly improved the soil up to 2 m in depth and commonly influenced the soil up to depths of 4 m.

• Journal of Fisheries and Marine Sciences Education
• /
• v.27 no.5
• /
• pp.1369-1379
• /
• 2015

This study attempted an AHP analysis through interview with experts in the industries and questionnaire survey on recognition of organization members and future strategic development direction in order to upgrade shipbuilding equipment industries to marine plant equipment industries. Key research results are as follows. First, according to analysis on relative priority between three aspects on acceleration of shipbuilding equipment industries, importance was shown in the order of acceleration of internal competence, acceleration of manufacturing technology, and acceleration of supply chain, which means that the aspect on acceleration of internal competence had relatively higher importance. Second, as for relative importance of detailed item evaluation per respective aspect, it was found that development of core competencies was high from the aspect on acceleration of internal competence, higher value-addition was high from the aspect on acceleration of manufacturing technology, and IT infrastructure construction was high from the aspect on acceleration of supply chain.

• Proceedings of the Society of Korea Industrial and System Engineering Conference
• /
• 2002.05a
• /
• pp.379-386
• /
• 2002

As the value and relative importance of service industry boosts in modern society, to strengthen competitiveness companies starts to recognize the quality of service as a key component in their business operations. Furthermore, companies that apply the quality of services as their competitive method are concentrating more on the area of quality control. Nevertheless, the previous researches related to this area were more focused on the aspect of measure rather than the control. In this paper, each fractionated customer group in consideration of its characteristics is made in use of estimating the quality of service using the conjoint analysis. The principal variable selective method which a small number of variables is used to control a large number of variables is applied. Hotelling's $T^2$ control chart is applied to administer many relative variables of the quality of service because it is a Multi-item. If abnormal indications appear by adding new data, the method to find and improve variables using MYT decomposition is suggested to apply.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.31B no.1
• /
• pp.64-71
• /
• 1994

In this paper, we propose orthogonal integer transform(OIT) with general form. Considering the orthogonality and magnitude value order of the DCT Matrix whose performance is found to be close to that of the KLT, known to be optimal. The proposed OIT matrix is composed of values minimizing Hibert-Schmidt norm among integer values which satisfy the condition of orthogonality and the relative magnitudes of the DCT matrix. Comparing the OIT with the DCT, CMT, and ICT in error characteristics, transform efficiency, and maximum reducible bit, it is shown that the performance of the OIT compares more closely to that of the KLT relative to the performances of the DCT, CMT, and ICT when N=8.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.9
• /
• pp.1688-1693
• /
• 2007

The aim of this paper is to develop and verify the system which can detect heart rate during exercise by using conductive fabric electrode and transportable measurement module. The experiment was performed under 4 conditions(resting, walking, jogging, running) and 18 subjects data are used. By using the ECG measurement system used in cardiac stress testing as reference value in order to verify the accuracy of the developed system, the relative error and correlation coefficient was calculated for each subject at every 3 seconds. The results have shown that the high correlation between the developed system and the reference system for detecting heart rate during exercise. Relative error and correlation coefficient are 2.27% and 0.9877, respectively. 7 subjects data are omitted in these calculations because of severe noises. Therefore, it is expected that this system could be used as a health monitoring system in ubiquitous environment in the future.

• Journal of Veterinary Clinics
• /
• v.18 no.1
• /
• pp.35-43
• /
• 2001

Present study was undertaken in order to document early renal ultrasonographic changes of gentamicin nephrotoxicosis and to show the value of renal ultrasonography as a contributory means of early diagnosis of acute renal failure in dogs. The experimental design was a randomized complete block design with six treatments in two blocks (gentamicin-treated & saline-treated). Acute renal failure was induced by toxic dosage of gentamicin (30 mg/kg) and saline solution sham equivalent in volume to that of the toxic dosage of gentamicin (1.5-3ml). Subjective visualization of increased renal cortex was visible as homogenous echoes that were hypoechoic relative to the surrounding tissues, whereas the renal medulla was anechoic to slightly hypoechoic. After treatment, the renal cortex was hyperechoic relative to the surrounding tissue. Increased renal cortex echogenicity was associated with significant nephrotoxicosis and was superior to serum creatinine elevation in nephrotoxicosis detection. Urine GGT was superior to other clinicopathological data utilized in the diagnosis of nephrotoxicosis. Based on the above results, increased renal cortex echogenicity seemed to be of use in detecting of acute renal failure.

• The Korean Journal of Financial Management
• /
• v.14 no.3
• /
• pp.319-339
• /
• 1997

This paper provides an empirical analysis of the winner's curse in the context of corporate takeovers. The study analyzes conditions which make overpayment likely. For a sample of corporate takeovers completed between 1982 and 1993, the analysis shows that the volatility of targets relative to that of acquirers (not the uncertainty of the target or acquirer alone) has a definitive impact on the magnitude of the winner's curse. Also, the incidence is more pronounced in multiple-bidder than in single-bidder contests. Specifically, white knights are more likely to overpay than other acquirers in multiple bidding situations. Furthermore, the study finds that the process of competitive bidding is a zero sum game since the greater returns to the shareholders of target firms in multiple-bid contests come at the expense of the acquiring companies, Overall, the evidence suggests that the bidders need to become more conservative, particularly as the relative uncertainty of the target's 'true' value and the number of bidders increase.

• The Journal of Korean Medicine
• /
• v.26 no.2 s.62
• /
• pp.105-125
• /
• 2005

Objectives: The purpose of this study was to identify resources put into clinical. activities and identify a new RBRVS for oriental medical services in the Korean National Health Insurance. Methods: Based on a survey of physician's time, physical effort & technical skill, mental effort & judgment, and stress that were used for patient treatments, relative input values for the relevant clinical activities were estimated and rearranged in a way to be compared. with the current values in health insurance. Results: We found the actual resource-based relative values for oriental medical services statistically different from the current values, with a narrower variation in value distribution. Conclusions: The findings suggest the C\lrrent RBRVS should be revised to reflect the actual input resources into physicians activities and to avoid a distortion of physicians behavior.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.2 s.95
• /
• pp.194-200
• /
• 1999

An elastomeric bushing is a device used in automotive suspension systems to cushion the force transmitted from the wheel to the frame of the vehicle. A bushing is an elastomeric hollow cylinder which is bonded to a solid metal shaft at its inner surface and a metal sleeve at its outer surface. For axial motion case, the relation between the force applied to the shaft and their relative displacement was considered. In this paper, the relation between the moment applied to the shaft and their relative deformation(angle of rotation) is considered for the torsional motion case. Numerical solutions of the boundary value problem represent the exact bushing response for use in the method for determining the moment relaxation function of the bushing. Solutions also allow for comparison between the exact moment-deformation behavior and that predicted the proposed model. It is shown that the predictions of the proposed moment-deformation relation are in very good agreement with the exact results.