• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1997.06a
• /
• pp.13-17
• /
• 1997

The densification of $Al_2$O$_3$/15v/o ZrO$_2$ (Zirconia Toughened Alumina: ZTA) to the 99% of theoretical density was attempted by controlling the processing parameters affecting the each processing step i.e., milling, spray-drying, forming and pressureless sintering. The ZTA processed under the identical conditions showed a large variation in the green and sintered densities, and the mechanical properties. The deviation of 4-point bending strength was more than 100MPa for the ZTA with ~99% of theoretical density. Moreover, the relative green and sintered densities were deviated greatly from the average value. This low reproducibility could be caused by the variation of spray-dried granule properties. Thus, the effect of yield strength and morphology of spray-dried ZTA granule on the green and sintered densities and the mechanical properties needs to be studied in detail. The objective of this work is to fine out the optimum condition of compaction pressure and compaction method depending on the properties of spray-dried granules.

• Journal of Powder Materials
• /
• v.5 no.4
• /
• pp.279-285
• /
• 1998

The microstructures and mechanical properties of submicron WC-Co cemented carbides were investigated in relation to cobalt content. To inhibit the WC grain growth during sintering, VC was added as a inhibitor in each alloy with 3 mass% to the cobalt content. The WC-(5, 8, 10, 15, 20) mass% Co compacts were sintered at $1400^{\circ}C$ for 30 min in vacuum. Some of WC-(5, 8, 10) mass% Co sintered compacts were HIPed with 120 atm at 130$0^{\circ}C$ for 1 hr. The shrinkages of all HIPed alloys were increased without depending on the cobalt contents and the sintered densities of them. The relative densities of the alloys were increased with the cobalt content and HIPing. The less the cobalt content, the larger the WC grain. Many contiguities of WC grains were found in WC-5 mass% Co alloy. The sizes and numbers of pores in the alloys were decreased by HIPing. And also the strength and the hardness of each alloy were increased. The maximum hardness was about 18.95 GPa in the WC-5 mass% Co alloy HIPed and the maximum transverse-rupture strength (T.R.S.) 3.2 GPa in the WC-20 mass% Co alloy sintered.

• Korean Journal of Materials Research
• /
• v.14 no.11
• /
• pp.795-801
• /
• 2004

The injection molded Fe sintered bodies were fabricated using two kinds of Fe powders haying 50 nm and $3\sim5{\mu}m$ in diameter. In the using of Fe powder having 50 nm in diameter, the comparatively dense bodies ($94\sim97\%$) were obtained even at low sintering temperature ($600\sim700^{\circ}C$), while in the sintered bodies ($1000^{\circ}C$) using $3\sim5{\mu}m$ Fe powder, their relative densities showed low values about $93\%$, although they were strongly depend on the sintering temperature and volume ratio of Fe powder and binder. In the sintered bodies using of 50 nm Fe powders, the volume shrinkage and grain size increased as the sintering temperature increased, but the values of hardness decreased. In the sample sintered at $650^{\circ}C$, the values of relative density, volume shrinkage and grain size were $96\%,\;37\%\;and\;0.97{\mu}n$, respectively and the minimum value of wear depth was obtained due to combination of fine grain and comparatively high density.

• Journal of the Korean Ceramic Society
• /
• v.29 no.3
• /
• pp.241-251
• /
• 1992

The effects of slip composition and processing conditions on the fabrication of ceramic heat exchanger cores by doctor blade process were investigated. Since the effects of those two variables were inter-dependent, the effects of binder system, binder plus plasticizer, were extensively studied for a limited range of processing conditions and a pre-determined ceramic composition. The content of binder system and the ratio of binder to plasticizer were identified as main variables to affect densities and mechanical properties of green sheets, compressive properties and bond strengths of laminates, and shrinkages and their anisotropy of sintered laminates. However, sintered densities and water absorptions of laminates were not influenced by either the content of binder system or the ratio of binder to plasticizer, when the debinded laminates had a relatively high density (relative density of >55% in this study).

• Journal of the Korean Ceramic Society
• /
• v.33 no.10
• /
• pp.1177-1185
• /
• 1996

Y-TZP/Ce-TZP ceramics having relative sintered densities of>95% average grain sizes of 0.36$\mu\textrm{m}$ microhar-dness of 1150 kg/mm2 fracture strength of 390-830 MPa and toughness of 6.4-10.2 MPa$.$mm1/2 were prepared by conventional sintering of 3 mol% Y2O3-ZrO2 and 12 mol% CeO2-ZrO2 powders at 1400 and 1500$^{\circ}C$ The average grain sizes of Y-TZP/Ce-TZP ceramics were mainly governed by those of Ce-TZP. White increasing Ce-TZP content toughness increased while microhardness and fracture strength decreased. With comparing microhardness and toughness fracture strength was more sensitive on not only grain size but also other factors such as microstructural and compositional variations. The densification of Y-TZP/Ce-TZP cermaics was not greatly affected by composition and soaking time at temperature over 1400$^{\circ}C$ With increasing CE-TZP content the stability of t-ZrO2 decreased under thermal aging in air whereas increased in hydrothermal atmosphere and aqueous solution.

• Journal of the Korean Ceramic Society
• /
• v.51 no.5
• /
• pp.442-446
• /
• 2014

Influences of Co and inhibitors from nano-sized WC materials were observed in the sintering process. VC and $Cr_3C_2$ were used as inhibitors. The crystal structure and surface images of sintered nano-sized WC materials, as functions of Co and inhibitors, were evaluated by XRD and FE-SEM analyses. The relative densities of sintered nano-sized WC materials did not change even with increased quantity of Co and increased temperature. The density of sintered nano-sized WC materials with inhibitors was lower than that of sintered nano-sized WC materials without inhibitors. No difference in hardness due to change of inhibitors was found.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.3
• /
• pp.206-210
• /
• 2010

$BaTiO_3$ dielectric ceramics are widely used to multi-layer ceramic capacitor. The $BaTiO_3$ powder was synthesized at $950^{\circ}C$ by using a solid state reaction and grinded by using a high-energy mill. And then, 2.53 wt% glass frit was added to the synthesized $BaTiO_3$ powders for lowering the sintering temperature. The mixed powders were sintered at various temperatures of $1170^{\circ}C$, $1200^{\circ}C$, $1230^{\circ}C$. Microstructures of the sintered $BaTiO_3$ ceramics were inspected by SEM and crystal structures were analyzed by XRD method. The relative dielectric constant was measured by using a impedance/gain phase analyzer. The synthesized $BaTiO_3$ powder had the tetragonal perovskite structure without secondary phase and the particle size was below 200 nm. The relative densities measured at the samples sintered at the temperature above $1200^{\circ}C$ were about 95%. The relative dielectric constant showed maximum value of 2310, which was measured in the specimen sintered at $1200^{\circ}C$. From these results, we could know that the added glass frit had effects on both lowering the sintering temperature and improving the dielectric property.

• Journal of Powder Materials
• /
• v.23 no.4
• /
• pp.282-286
• /
• 2016

A sintered body of $TiB_2$-reinforced iron matrix composite ($Fe-TiB_2$) is fabricated by pressureless-sintering of a mixture of titanium hydride ($TiH_2$) and iron boride (FeB) powders. The powder mixture is prepared in a planetary ball-mill at 700 rpm for 3 h and then pressurelessly sintered at 1300, 1350 and $1400^{\circ}C$ for 0-2 h. The optimal sintering temperature for high densities (above 95% relative density) is between 1350 and $1400^{\circ}C$, where the holding time can be varied from 0.25 to 2 h. A maximum relative density of 96.0% is obtained from the ($FeB+TiH_2$) powder compacts sintered at $1400^{\circ}C$ for 2 h. Sintered compacts have two main phases of Fe and $TiB_2$ along with traces of TiB, which seems to be formed through the reaction of TiB2 formed at lower temperatures during the heating stage with the excess Ti that is intentionally added to complete the reaction for $TiB_2$ formation. Nearly fully densified sintered compacts show a homogeneous microstructure composed of fine $TiB_2$ particulates with submicron sizes and an Fe-matrix. A maximum hardness of 71.2 HRC is obtained from the specimen sintered at $1400^{\circ}C$ for 0.5 h, which is nearly equivalent to the HRC of conventional WC-Co hardmetals containing 20 wt% Co.

• Journal of Powder Materials
• /
• v.1 no.2
• /
• pp.167-173
• /
• 1994

Cu-10wt%W composite powders have been manufactured by a high energy ball milling technique. The composite powders were pressed at 250 MPa and sintered in a dry hydrogen at 103$0^{\circ}C$ for 4 hours. After sintering, Cu-10wt%W composite materials were forged. And the arc-resistance of forged materials which have the same relative density of 94% has been tested. Composite particles, i.e. tungsten particles distributed homogeneously in the copper matrix, was formed after 480 min mechanical alloying. Densities of these sintered materials were ranged from 74 to 84%. Densification degree was due to the formation of composite powders. As the mechanical alloying time increased, the hardness was increased and tungsten particle size was decreased. Arc loss of the forged specimens was decreased as increasing the mechanical alloying time.

• Journal of Powder Materials
• /
• v.7 no.3
• /
• pp.149-153
• /
• 2000

In this study, the fabrication of $Al_2O_3$/5vol.%Cu nanocomposite and its mechanical property were discussed. The nanocomposite powders were produced by high energy ball milling of $Al_2O_3$ and Cu elemental powders. The ball-milled powders were sintered with Pulse Electric Current Sintering (PECS) facility. The relative densities of specimens sintered at $1200^{\circ}C$ and $1250^{\circ}C$ after soaking process at $900^{\circ}C$ were 96% and over 97%, respectively. The sintered microstructures were composed of $Al_2O_3$ matrix and the nano-sized Cu particles distributed on grain boundaries of $Al_2O_3$ matrix. The nanocomposite exhibited the enhanced fracture toughness compared with general monolithic $Al_2O_3$. The toughness increase was explained by the crack deflection and bridging by dispersed Cu particles.