• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.11
• /
• pp.142-149
• /
• 2003

Domain switching effect on crack growth in ferroelectric ceramics under combined electric and mechanical loading is investigated. The shape and size of the switching zone is shown to depend strongly on the relative magnitude between the applied electric field and stress field as well as on the ratio of the coercive electric field to the yield electric field. The toughening mechanism is thought to be ferroelectric domain switching leading to the development of a process zone around the crack. Crack-tip stress intensity factor induced by domain switching for the steady state crack growth is numerically obtained.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.3
• /
• pp.174-183
• /
• 2000

Non-Parallelism the axial direction occurs during grinding process of long slender shafts. The reason for the axial error is due to elastic deformation of the components, accumulation phenomenon of the grinding and wheel wear during the grinding process. The accumulation phenomenon, the size generation mechanism and the wheel wear process during traverse grinding result in complicated process at each step on the wheel surface. The grinding system stiffness obtained from the stiffness of the center on the tailstock and the workpiece varing according to the relative position of the wheel and the workpiece. Further more, the value of wheel wear increases as the grinding process advances. The above mentioned issues make the shape generation process during traverse grinding quite complicated. This research analyzes the shape generation process in the direction of the work spindle. First, the formulation of the grinding system stiffness was conducted and the simulation analysis method of the traverse grinding was established. Also, a measuring system for assessing the dimensinal accuracy of the workpiece has been developed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.1114-1119
• /
• 1995

This paper presents the development of estimation model and control method based on the new computer vision. This proposed control method is accomplished using a sequential estimation scheme that permits placement of the rigid body in each of the two-dimensional image planes of monitoring cameras. Estimation model with six parameters is developed based on a model that generalizes known 4-axis scara robot kinematics to accommodate unknown relative camera position and orientation, etc. Based on the estimated parameters,depending on each camers the joint angle of robot is estimated by the iteration method. The method is tested experimentally in two ways, the estimation model test and a three-dimensional rigid body placement task. Three results show that control scheme used is precise and robust. This feature can open the door to a range of application of multi-axis robot such as assembly and welding.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.497-500
• /
• 1995

In this paper, a program for real time simulation of a vehicle is developed. The program uses relative coordinates and BEF(Backward Difference Formula) numerical integration method. Numerical tests showed that the proposed implicit method is more stable in carring out the numerical integration for vehicl dynamics than the explicit method. Hardware requirements for real time simulation are suggested. Algorithms of parallel processing is developed with DSP (digital signal processor).

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.10
• /
• pp.71-77
• /
• 1996

This paper describes the development of on the machine measuring(OMM) system which can directlry measure the three dimensional machined dimensilnal accuracy using scanning probe in milling machine. Two algolithms, continuous path(CP) measurement using UC program and CAD data assisted point to point(PTP) measurement, were developed regarding specification of scanning probe. The OMM system was contructed to verify the developed system suing the proposed algorithm, and actually measured three kinds of machined TV shadow mask molds. The developed system was evaluated it's repeatability and compared with the current measurement system of CMM(Coording Measuring Machine) in terms of relative accuracy and time reduction and productivity increase.

• Natural Product Sciences
• /
• v.10 no.6
• /
• pp.262-267
• /
• 2004

A reversed-phase liquid chromatographic method for decursin and decursinol angelate of Angelicae gigantis Radix, an important crude drug in Korean traditional medicine, was developed and validated. Decursin and decursinol angelate, the structure isomer (pyranocoumarin) each other, are the main organic constituents in Angelicae gigantis Radix. This method was developed using a RP-18 column, UV detector at 280 nm and 50% acetonitrile solution containing 0.01 M sodium dodecyl sulfate and 25 mM sodium dihydrogen phosphate (pH 5.0) as the mobile phase. Various validation parameters were included and evaluated satisfactorily. Linearity was established in range 2-75 mg/ml of decursin and decursinol angelate (correlation coefficient = 0.9997 and 0.9995, respectively). This analytical method showed good accuracy (98.1% and 99.5%, respectively). Precision (repeatability) revealed a relative standard deviation value of 1.71% (decursin) and 3.19% (decursinol angelate). For intermediate precision measure the considered variables were equipment and days. A robustness test showing the influence of deferent counter-ion concentration in mobile phase was also performed.

• International Journal of Precision Engineering and Manufacturing
• /
• v.3 no.3
• /
• pp.50-55
• /
• 2002

A roller gear cam mechanism is presented. It consists of two or more plate cams with particular teeth, called Conjugate Cam Tooth (CCT) and a turret with axially located rollers. A practical and available configuration has been found out by synthesizing its parameters. The profile equations of the conjugate cam are derived by using a relative velocity method. A program fur the design automation of shape of the conjugate cam and the motion simulation of this kind of mechanism has been deve1oped using the derived formulae with C++ language. Finally, an example is given.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.311-315
• /
• 2001

This paper presents the result of basic study about corrective polishing for arbitrary surface figure. In this study, we researched polishing characteristics on the working condition of optical glass. The abrasive size, relative velocity and working pressure were selected major factors that affect polishing process. The Preston's equation which is the representative model of polishing process was used to model the unit removal shape. The Preston's coefficient and unit removal function were calculated from the polished surface. Applying these results, we have shown that the systematic corrective polishing of arbitary figure is feasible through experiments and analysis.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.445-450
• /
• 2000

In this paper, a numerical method is proposed for cam synthesis. kinematics of closed loop system with cam and follower is presented using relative coordinates. The system is transformed into an open loop system by cutting fictitiously higher-pair contact of cam and follower and envelope constraint equations are derived. Follower constraint equations are derived from the motion of the follower ends. The joint variables and follower profile parameters are calculated from the envelope constraint equations and follower constraint equations by using the Newton - Raphson iterative method. Algorithms for cam synthesis are presented and simulations are done to verify the effectiveness of the proposed method.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.6 no.3
• /
• pp.9-15
• /
• 2007

Three methods for grinding: cross grinding, slanted tool axis grinding and parallel grinding, were carried out to study the machinability of tungsten carbide mold for glass formed aspherics lens. In our research, the optimum grinding conditions were investigated in terms of feed-rate, relative velocity of wheel and work piece, tool marks and surface roughness. It is shown that cross grinding are most effective in removal ratio but poor in surface roughness. In addition, tool marks of each method were differentiated on direction and shape.