• Smart Structures and Systems
• /
• 제25권6호
• /
• pp.669-678
• /
• 2020

This paper focuses on the free vibration analysis of axially functionally graded (FG) Euler-Bernoulli beams. The material properties of the beams are assumed to obey the linear law distribution. The complexities in solving differential equation of transverse vibration of composite beams which limit the analytical solution to some special cases are overcome using the Differential Transformation Method (DTM). Natural frequencies and corresponding normalized mode shapes are calculated. Validation targets are experimental data or finite element results. Different parameters such as reinforcement distribution, ratio of the reinforcement Young's modulus to the matrix Young's modulus and ratio of the reinforcement density to the matrix density are taken into investigation. The delivered results prove the capability and the robustness of the applied method. The studied parameters are demonstrated to be very crucial for the normalized natural frequencies and mode shapes.

• 한국터널지하공간학회 논문집
• /
• 제5권2호
• /
• pp.189-198
• /
• 2003

터널의 대단면화에 따라 각 암반 지보의 역할과 그 보강효과를 확인하고 보다 합리적인 지보구조로의 변화가 요구되고 있다. 특히, 굴착직후 숏크리트에 의한 지보효과가 효과적이지 못한 터널에서는 지보 매커니즘에 대한 추가적인 검토가 필요하다. 강도가 발생하지 않는 터널이 가장 불안한 상태에 있을 때의 지보구조는 충분한 검토가 필요하다. 본 논문에서는 약재령 (若材令)시 록볼트에 의한 보강효과를 볼트 그라우트재의 경화를 고려하여 모의암반에 의한 실험 및 수치해석을 실시하여 시간의존에 따른 그라우트재의 압축강도와 재령, 부착강도와 재령, 부착강성과 재령과의 관계를 명확하게 하는 것으로 굴착직후의 록볼트의 암반보강 효과를 검토하고, 약재령시 록볼트의 모델화 및 물리정수를 산정하였다. 또 그라우트재의 효과를 가지지 않고도 해결되는 수압팽창형 프리쿠션볼트에 의한 굴착직후의 암반보강효과에 대해서도 검토하였다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2019년도 춘계 학술논문 발표대회
• /
• pp.85-86
• /
• 2019

Recently, the educational facilities were 45% among total damaged facilities from the Po-Hang earthquake. Consequently, the seismic reinforcement of existing educational facilities were ended up attracting people's interesting. However, research is insufficient to consider that how far technology has been developed. Therefore, the purpose of this study is to investigate the level of domestic guideline research by comparing to foreign guidelines in regard to seismic reinforcement methods applicable to existing educational facilities. To achieve the objective, first, the current status of seismic reinforcement projects in domestic educational facilities was analyzed. Second, the domestic and foreign seismic reinforcement methods guidelines for structural, non-structural was compared. Third, the improvement directions for future guidelines were suggested. As a results, the improvement directions of domestic seismic reinforcement methods guidelines were proposed. First, the structural seismic reinforcement strategy needs to be segmented. Second, it is necessary to analyze about non-structural guidelines based on additional cases. In the future, this study can be used as a basic material for developing seismic reinforcement methods guidelines in domestic existing educational facilities.

• 대한토목학회논문집
• /
• 제42권5호
• /
• pp.607-616
• /
• 2022

전 세계적으로 이상 기후 및 자연재난 등으로 인하여 철근콘크리트 구조물의 부식 및 열화 현상이 빈번히 발생됨에 따라 구조물의 노후화가 가속화되고 있다. 건설 분야에서는 이러한 내하력 저하에 대응하기 위하여 최근 저 중량 고강도 재료 장점을 가진 유리섬유 복합재료(GFRP)를 활용하여 많은 노후 구조물에 대하여 보수·보강을 수행하고 있다. 본 연구에서는 유리섬유에 비하여 보다 경제적이고 친환경적인 바잘트 섬유 복합재료(BFRP)를 활용하여 콘크리트 압축부재의 내진보강을 위한 횡구속 효과를 더욱 효과적으로 제공할 수 있는 보강재를 개발하고 그 성능을 평가하였다. 실험 시 고려된 주요 변수로는 바잘트섬유 복합재료(BFRP) 시공 시 적용되는 함침 수지의 양생 온도와 대상 콘크리트 압축부재의 재료 특성을 고려하였다. 콘크리트 압축부재의 재료 특성에 따른 횡구속 보강효과를 조사하기 위하여 본 연구에서는 일반 콘크리트와 섬유 보강을 통하여 내구성능이 개선된 콘크리트 시험체를 각각 제작하여 성능을 평가하였다. 그 결과, 일반 콘크리트의 경우 3.15배, 섬유 보강 콘크리트의 경우 약 3.72배의 보강 효과가 나타났으며 압축부재 내구특성 개선에 따른 보강 효과의 차이는 크지 않음을 알 수 있었다. 마지막으로 GFRP 압축부재 보강재에 대한 선행연구 결과를 통하여 바잘트 보강 복합재료의 성능을 비교한 결과 BFRP 보강재의 횡구속 보강효과가 상대적으로 약 1.18배 GFRP 보강재에 비하여 성능이 우수한 것으로 나타났다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 지반공학 공동 학술발표회
• /
• pp.581-590
• /
• 2005

The grouting method is widely used as the impermeable effect and ground reinforcement in construction. But, it has a problem that cement and grout material are not mixed well in the injection tip equipment and an opposite flow and interception state of the chemical grouting is happened. so, continuous work is difficult. McG method installed a special grouting and device, made possible go well mixing of grouting material and prevent flowing backward and block of nozzle also diversify powder rate of cement that is grouting material to select sutible material in layer conditions. YSS that lowered $Na_2O$ influencing durability and circumstance is developed by gel-forming reaction material. so eco-circumstance and durability is increased by minimizing dissolution of underground water. In this study, it is assumed that seepage state of the injection material using a special injection tip equipment and a unconfined compressive strenth by mixing a various injection material of various. And it is confirmed that strenth increase effect and permeable decrease of the improved body through the test execution and field execution.

• Computers and Concrete
• /
• 제21권2호
• /
• pp.127-137
• /
• 2018

In this study, the behavior of the number of anchorage bolts on the glass-fiber reinforced polymer (GFRP) plates adhered to the surfaces of reinforcing concrete (RC) T-beams was investigated analytically. The analytical results were compared to the test results in term of shear strength, and midpoint displacement of the beam. The modelling of the beams was conducted in ABAQUS/CAE finite element software. The Concrete Damaged Plasticity (CDP) model was used for concrete material modeling, and Classical Metal Plasticity (CMP) model was used for reinforcement material modelling. Model-1 was the reference specimen with enough sufficient shear reinforcement, and Model-2 was the reference specimen having low shear reinforcement. Model-3, Model-4 and Model-5 were the specimens with lower shear reinforcement. These models consist of a single variable which was the number of anchorage bolts implemented to the GFRP plates. The anchorage bolts of 2, 3, and 4 were mutually mounted on each GFRP plates through the beam surfaces for Model-3, Model-4, and Model-5, respectively. It was found that Model-1, Model-3, Model-4 and Model-5 provided results approximately equal to the test results. The results show that the shear strength of the beams increased with increasing of anchorage numbers. While close results were obtained for Model-1, Model-3, Model-4 and Model-5, in Model-2, the rate of increase of displacement was higher than the increase of load rate. It was seen, finite element based ABAQUS program is inadequate in the modeling of the reinforced concrete specimens under shear force.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.303-314
• /
• 2010

This study, as basic research which was intended to develope the surface reinforcement method using reinforcement material which is applicable to very soft ground in Korea, was aimed at proposing the design parameter for the surface ground improvement method. To that end, a wide width tensile test using geotextile, geogrid and steel bar (substitute for bamboo) and 49 kinds of the laboratory model tests were conducted. And the result the study suggested $\beta_s$, the stiffness coefficient to evaluate the stiffness effect of reinforcement materials. Then, it was also found that the stiffness coefficient, $\beta_s$ as the testing constant would be appropriate as high as 1.0, 1.1 and 1.5 for geotextile, geogrid and steel bar, respectively. And It was evaluated that the stiffness effect affecting reinforcement improvement effect would be reduced as the thickness of embeded depth increases and that RFe, the stiffness effect reduction coefficient would have positive correlation with H/B. Finally, it was confirmed that the bearing capacity gained from the method to calculate bearing capacity, which was suggested in the study, would almost correctly estimate the capacity, demonstrating the appropriateness of the proposed bearing capacity calculation method.

• Earthquakes and Structures
• /
• 제7권4호
• /
• pp.463-484
• /
• 2014

Solid piers with a rounded rectangular cross-section are widely used in railway bridges for high-speed trains in China. Compared to highway bridge piers, these railway bridge piers have a larger crosssection and less steel reinforcement. Existing material models cannot accurately predict the seismic behavior of this kind of railway bridge piers. This is because only a few parameters, such as axial load, longitudinal and transverse reinforcement, are taken into account. To enable a better understanding of the seismic behavior of this type of bridge pier, a simultaneous influence of the various parameters, i.e. ratio of height to thickness, axial load to concrete compressive strength ratio and longitudinal to transverse reinforcements, on the failure characteristics, hysteresis, skeleton curves, and displacement ductility were investigated. In total, nine model piers were tested under cyclic loading. The hysteretic response obtained from the experiments is compared with that obtained from numerical studies using existing material models. The experimental data shows that the hysteresis curves have significantly pinched characteristics that are associated with small longitudinal reinforcement ratios. The displacement ductility reduces with an increase in ratio of axial load to concrete compressive strength and longitudinal reinforcement ratio. The experimental results are largely in agreement with the numerical results obtained using Chang-Mander concrete model.

• 한국농촌건축학회논문집
• /
• 제21권2호
• /
• pp.35-42
• /
• 2019

There are 17,427 reservoirs in Korea, of which about 96% were built before the mid 1980s. Therefore, aging is severe and reinforcement are necessary. In addition, aged reservoirs, which are more than 50 years old, account for 70% of the total. Therefore, there is a problem such as the collapse of the reservoir and the decrease of the storage capacity due to progress of aging with time. The grouting method using cement is mainly used as maintenance and reinforcement method of old reservoir. However, the grouting method using cement has engineering and environmental problems. In order to solve the engineering and environmental problems of cement grouting method, an eco-friendly grouting material was developed that mixes circular resource grouting binder, high molar ratio sodium silicate and colloidal silica. The engineering and environmental properties of the developed injection materials were evaluated by conducting gel time, homo-gel strength, sea water resistance test and environmental stability evaluation. Also, examined the possibility of replacing OPC existing aged reservoir reinforcement methods. As a result, it was found out that it was better than the conventional cement method in terms of engineering and environment. However, since this study is the result of laboratory test, it is necessary of verify the application at field of aged reservoir.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2005년도 추계 학술발표회 제17권2호
• /
• pp.121-124
• /
• 2005

The existing reinforcement methods of construction are the actual condition without the method of checking exact injection of adhesives clearly by the opacity of reinforcement material. In this study, in order to solve such a problem, the high strength transparent panel using a glass fiber is developed and in order to examine reinforcement effect of a panel clearly, the structure performance evaluation experiment was conducted. As a result, we knew that it can check with the naked eye the injection process of adhesives and reinforcement effect was also observable.