• Journal of the Korean Wood Science and Technology
• /
• 제39권2호
• /
• pp.156-162
• /
• 2011

To evaluate the bonding performance of reinforced glulam, the textile type of glass fiber and aramid fiber, and the sheet type of glass fiber reinforced plastic (GFRP) and carbon fiber reinforced plastic (CFRP) were used as reinforcements. The reinforced glulam was manufactured by inserting reinforcement between the outmost and middle lamination of 5ply glulam. The types of adhesives used in this study were polyvinyl acetate resins (MPU500H, and MPU600H), polyurethane resin and resorcinol resin. The block shear strengths of the textile type in glass fiber reinforced glulam using MPU500H and resorcinol resin were higher than 7.1 N/$mm^2$, and these glulams passed the wood failure requirement of Korean standards (KS). In case of the sheet types, GFRP reinforced glulams using MPU500H, polyurethane resin and resorcinol resin, and CFRP reinforced glulams using MPU500H and polyurethane resin passed the requirement of KS. The textile type of glass fiber reinforced glulam using resorcinol resin after water and boiling water soaking passed the delamination requirement of KS. The only GFRP reinforced glulam using MPU500H after water soaking passed the delamination requirement of KS. We conclude that the bonding properties of adhesive according to reinforcements are one of the prime factors to determine the bonding performance of the reinforced glulam.

• 대한치과교정학회지
• /
• 제29권1호
• /
• pp.107-112
• /
• 1999

성인 교정 환자가 증가됨에 따라 교정장치의 심미성이 요구되고 있다. 교정 장치의 심미적 증진을 위해 개발된 브라켓들로는 세라믹, 콤포지트 레진 브라켓, 타이타늄 브라켓등이 소개되고 있다. 콤포지트 레진 브라켓은 우수한 색상 및 투과성이 장점이나 높은 마찰력과 낮은 취성의 단점을 갖고 있다. 이러한 단점을 보완하기 위하여 최근 개발된 세라믹 또는 레진 브라켓(metal reinforced bracket)은 마찰력을 감소시키고 강도를 증가시키기 위하여 브라켓의 슬롯에 메탈을 삽입하고 있다. 그러나 지금까지 이러한 metal reinforced resin bracket(이후 MRRB)의 물성에 관한 연구가 미진하였다. 특히 이러한 브라켓과 교정용 철선의 마찰력에 관한 연구가 미흡하기에 본 연구를 시행하였다. 본 연구는 4종의 교정용 철사(.016 S-S, .0l6X.022 S-S, .016 $TMA^{\circledR}$, .0l7X.025 $TMA^{\circledR}$)와 5종의 브라켓을 사용하였다. 사용된 브라켓들로는 메탈 1종(Ormco.Co., U.S.A)자 세라믹 1종($Crystalline^{\circledR}$), 콤포지트 레진 1종(Clear Medium $Siamase^{\circledR}$), 메탈 슬롯이 삽입된 콤포지트 레진2종($Plastic^{\circledR},\;Spirit^{\circledR}$)의 마찰력을 서로 비교하여 다음과 같은 결과를 얻었다. 1. ceramic bracket과 resin bracket은 metal reinforced resin bracket과 metal bracket보다 마찰력이 유의성 있게 크게 나타났다. 2. metal reinforced resin bracket의 slot내 metal의 삽입형태에 따른 마찰력의 크기는 유의차가 없었다. 3. metal reinforced resin bracket과 metal bracket사이의 마찰력의 크기는 유의차가 없었다. 4.. 교정용 철선과 각 브라켓 비교에서 TMA, Stainless steel 순으로 마찰력이 적게 나타났다.

• 동력기계공학회지
• /
• 제18권5호
• /
• pp.106-114
• /
• 2014

For the purpose of development of polyurethane sealing material, polyurethane resins reinforced with CuO were prepared from polyol and MOAC(4,4'-Methylenebis(2-chlorobenzeneamine)). And the effects of compositions on the mechanical properties of the reinforced polyurethane resin were experimentally examined. The polyurethane resin got to be thermally decomposed at $260^{\circ}C$ and completely carbonized around $500^{\circ}C$. Tensile strength, elongation and hardness of the polyurethane resin increased with the content of MOCA. CuO was uniformly dispersed in the polyurethane resin by 1 minute's ultrasonic radiation. Tensile strength, elongation and hardness of the polyurethane resin reinforced with CuO increased with the content of CuO. Tensile strength and hardness of the reinforced polyurethane resin increased with particle size of the CuO, but elongation decreased. CuO showed higher tensile strength and hardness than any other additives, and lowest elongation.

• International Journal of Precision Engineering and Manufacturing
• /
• 제1권1호
• /
• pp.33-41
• /
• 2000

Fiber reinforced metal laminates(FRMLs) were new type of hybrid materials. FRMLs consist of high strength metals(Al 5052-H34) and laminated fiber with structural adhesive bond. The effect of resin mixture ratios on the fatigue crack propagation behavior and mechanical properties of aramid fiber reinforced aluminum composites was investigated. The epoxy, diglycidylether of bisphenol A(DGEBA), was cured with methylene dianiline(MDA) with or without an accelerator(K-54). Eight kinds of resin mixture ratio were used for the experiment ; five kinds of FRMLs(1)(mixture of epoxy and curing agent) and three kinds of FRMLs(2)mixture of epoxy, curing agent and accelerator). The characteristic of fatigue crack propagation behavior and mechanical properties FRMLs(2) shows more effecting than that of FRMLs(1).

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1992년도 봄 학술발표회 논문집
• /
• pp.35-40
• /
• 1992

Results of an experimental study on the manufacture, the workability and mechanical properties of steel fiber reinforced polyester resin composites utilizing industrial waste products are presented in this paper. The fly ash polyester resin composites using steel fiber, fly ash and calcium carbonic acid (CaCo3), unsaturated polyester resin, styrene monomer, cobalt octate and methyl ethyl ketone peroxide, fine and coarse aggregates are prepared with various filler~binder rations, binder rates and mixing conditions. As a test results, the workability of steel fiber reinforced polyester resin composites are considerably dropped with increasing fly ash-binder ratio and steel fiber volume. And compressive, flexural strength and bending toughness of the composites are remarkably improved with augmenting fiber contents.

• 한국농공학회지
• /
• 제25권2호
• /
• pp.67-75
• /
• 1983

The objectives of this paper were to measure the bond strengths of reinforced concrete in which the steel rods were coated with five different kinds of anticorrosion paints, and to compare their prevention effects in salt water. The paints used in the study were epoxy resin I . II . III, Z.R. P., and silicone resin, which were applied at rates recommended by the manufacturers. The bond strengths were measured on the 7-, 14-, and 28-th days after molding. Corrosion conditions of coated steel plate under fresh water, seawater, 10 % salt water, and 20% salt water, were inspected every month during four months test peoriods, respectively. The results obtained from tests are summarized as follows: 1. Paint-coating may reduce the bond strengths of reinforced concrete. Silicone resin paint showed some 20% reduction in the strength compared to those without the paint. However, the other paints seemed not to significantly affect the strength. 2. Picture analyses showed that epoxy resin I and II significantly prevented corrosion steel plates in seawater. Epoxy resin I and silicone resin coating did not do a good job in corrosion prevention. Z.R. P. paint was found to be moderate as preventive coating paint. 3. Varying soluble salt contents had little effects on the corrosion prevention of tested paints. 4. Epoxy resin I and II were found to be appropriate as a coating material to prevent the corrosion of steel rods in seawater. Z.R.P. may also be used for the purpose.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.277-283
• /
• 2004

The time to ignition, heat release rate characteristics and carbon monoxide yield of fiber reinforced and sandwich phenol resin were investigated with cone calorimeter. The fire characteristics of unsaturated polyester, mostly being applied to the existing passenger train, and phenolic resin were compared. Thermal gravimetric analysis(TGA) was used to monitor the degree of thermal decomposition for the phenolic resin. According to the cone calorimeter data, the time to ignition, heat release rate and CO yield was faster and higher as the external heat flux increase. Under the same heat flux, the time to ignition of sandwich type phenolic resin was shorter than that of fiber reinforced. The result of comparison between unsaturated polyester and phenolic resin was that phenolic resin was shown to have better fire resistance than that of unsaturated polyester.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2018년도 춘계 학술논문 발표대회
• /
• pp.54-55
• /
• 2018

Reinforced concrete is a building material that is generally used in modern society. Securing the performance of reinforced concrete is directly connected to the durability and longevity of the building. One of the major factors that deteriorate the durability of concrete is harmful ion. Recently, the quality and improvement method of reinforced concrete for penetration of harmful ion has been studied. In this study, the bead type ion exchange resin is substituted for 0%, 3%, and 6% of the fine aggregate volume in the mortar. The speciments underwent underwater curing and were checked for compressive strengths of 3 days and 28 days. From the results of compressive strength, it can be seen that the higher the substitution ratio of the ion exchange resin, the lower the early strength and long-term strength development, especially the early strength development.

• 대한전기학회논문지
• /
• 제41권6호
• /
• pp.640-651
• /
• 1992

This paper describes the electric properties of mica reinforced silicone composites with the parameter of curing condition of silicone resin, application amount of silane coupling agent to the mica paper and the mica wt% to the composite. Heat-resistant silicone resin and mica paper made of mica flakes are used to prepared the mica/silicone composite as matrix and filler, respectively. To improve the dielectric properties and interfacial adhesion between matrix and filler, silane coupling agent is applied on the mica paper. As for matrix, tan$\delta$ value of 30$0^{\circ}C$ heat-treated silicone resin is the lowest under 1%. The optimal wt% of coupling agent is 0.3% to the weight of mica paper. 80 wt% of mica as filler to the mica/silicone composite shows the best electric properties. And the mica reinforced silicone composite shows good high-frequency and mechanical tensile stress properties.

• 폴리머
• /
• 제24권4호
• /
• pp.459-468
• /
• 2000

유리 또는 아라미드 섬유를 보강재로 사용한 섬유강화 복합재료의 기계적 물성을 증진시키기 위하여 복합재료 적층판을 서로 다른 매트릭스 수지와 섬유를 선정하여 이들의 인장, 굴곡 특성을 조사하였다. 불포화 폴리에스테르와 개질된 표면의 아라미드 섬유 복합재료의 경우, 굴곡 물성의 최대값은 실란 농도가 0.5 wt%일 때 관찰되었다. 불포화 폴리에스테르 수지와 유리섬유 복합재료의 인장 물성은 vinylester계가 가장 높게 나타났으며, 굴곡물성은 isophthalic계가 가장 높은 물성을 나타내었다. 유리섬유와 불포화 폴리에스테르 수지 복합재료의 기계적 물성을 증진시키기 위해 겹침 적층판과 기계적 물성과의 상관 관계에 대해서도 연구가 병행되었다.