• 한국지하수토양환경학회지:지하수토양환경
• /
• 제17권3호
• /
• pp.21-31
• /
• 2012

This paper presents the short-term and long-term measures to determine the fugitive dust concentration in a contaminated site, which is a crucial step for the determination of particulate emission factor (PEF) for risk assessment. As a long-term measure, USEPA method employing Q/C value (inverse of the ratio of the geometric mean air concentration to the emission flux at center of a 0.5-acre square source) seems to be suitable as it reflects regional-specific meteorological conditions. However, it requires nation-wide database collection and interpretation. Use of ASTM method is an alternative as a short-term measure. The method is readily field-applicable as PEF calculation equation is simple and input parameters can be easily derived at the site of interest as well without the nation-wide efforts. Using ASTM method, PEF at the Former Janghang Smelter Site was determined. According to various mode of aggregate size distribution and fractions of vegetative cover, which are the most important factors in PEF calculation, PEF values at the Former Janghang Smelter Site varied greatly. When the mode of aggregate size distribution was set at 0.25 mm, PEF values at the Former Janghang Smelter Site was 5~20 times higher than the default PEF value (i.e., 35 ${\mu}g/m^3$) shown in the current Korean Soil Contamination Risk Assessment Guidance. On contrast, when the mode was set at 2 mm, PEF values at the Former Janghang Smelter Site was 160~640 times lower than the default PEF value in the Korean Guidance.

• 한국물환경학회지
• /
• 제30권6호
• /
• pp.638-646
• /
• 2014

Soil erosion from agricultural fields leads to various environmental problems weakening the capabilities of flood control and ecosystem in water bodies. Regarding these problems, Ministry of Environment of South-Korea prepared various structural and non-structural best management practices (BMPs) to control soil erosion. However, a lot of efforts are required to monitor and develop BMPs. Thus, modeling techniques have been developed and utilized for these issues. This study estimated the effectiveness of BMPs which are a vegetation mat with infiltration roll and Roll type vegetation channel using Soil and Water Assessment Tool (SWAT) model through the adjustment of the conservation practice factors, P factors, for Universal Soil Loss Equation which were calculated by monitoring data collected at the segment plots. Each BMP was applied to the areas with slopes ranged from 7% to 13% in the Haeanmyeon watershed. As a result of simulation, the vegetation mat with infiltration roll and Roll type vegetation channel showed 55% and 59% efficiency of soil erosion reduction, respectively. Also, Vegetation mat with infiltration roll and Roll type vegetation channel showed each 11.2% and 11.8% efficiency in reduction of sediment discharge. These roll type vegetation channel showed greater efficiency of soil erosion reduction and sediment discharge. Based on these results, if roll type vegetation channel is widely used in agricultural fields, reduction of soil erosion and sediment discharge of greater efficiency would be expected.

• 한국환경보건학회지
• /
• 제33권6호
• /
• pp.502-505
• /
• 2007

To estimate the soil quality of Miryang area, soil analysis were conducted according to the city and out of city of soil expenses at according to analysis components and heavy metal pollution of irradiation sampling sites. The through soil components the principal element about the 71% $SiO_2\;and\;Al_2O_3$, the pH of field area near the city center was lower than that of the other field area, which indicated that this acidification was probably attributed to the acid rain caused by the traffic exhaust gas such as $SO_x\;and\;NO_x$. Acidification was more severe in the field area than in the farming land. The concentration of five heavy metals such as Cu, Cd, Pb, As and Cr were found to be lower than the standard of soil pollution. An assessment using the SPI(Soil Pollution Index), which was developed to estimate an overall soil quality, was performed. Each SPS(Soil Pollution Score) were evaluated with the results of the data from this study. The soil quality of most area of Miryang land was determined to Class 1, which indicated that the soil was healthy.

• 한국환경복원기술학회지
• /
• 제2권3호
• /
• pp.64-73
• /
• 1999

The purpose of this study is to establish the management plannings for the conservation and environmentally friendly use of Korean coastal wetlands. The function, economic value, and the necessity for the conservation of coastal wetlands are described. The current management status, Korean Governmental policies for the use of coastal wetlands, and their problems are surveyed and analysed. The management plannings for the environmentally friendly use of Korean coastal wetlands is suggested as follows: (1) The coastal wetlands need to be divided into 3 different regions based on PSR(Pressure, State, Response) of OECD. (2) Each region should be managed by appropriate management plans which are suggested in Chapter IV of this paper. Finally, in order to realize these management plannings the change of Governmental system and laws are suggested as follows: (1) The change of relevant laws is required. Additionally, each region should managed by proper governmental agencies. (2) The EIA(Environmental Impact Assessment) system should be improved. (3) The participation of regional people should be guaranteed in the decision making processes of the business and other important planning regarding coastal wetlands. (4) The system which primed the ecological value of coastal wetlands should be established.

• Geomechanics and Engineering
• /
• 제34권4호
• /
• pp.341-380
• /
• 2023

This study evaluates the seismic fragilities in fill slopes in South Korea through parametric finite element analyses that have been barely investigated thus far. We consider three slope geometries for a slope of height 10 m and three slope angles, and two soil types, namely frictional and frictionless, associated with two soil states, loose and dense for frictional soils and soft and stiff for frictionless soils. The input ground motions accounting for four site conditions in South Korea are obtained from one-dimensional site response analyses. By comparing the numerical modeling of slopes using PLAXIS^2D against the previous studies, we compiled suites of the maximum permanent slope displacement (D_max) against two ground motion parameters, namely, peak ground acceleration (PGA) and Arias Intensity (I_A). A probabilistic seismic demand model is adopted to compute the probabilities of exceeding three limit states (minor, moderate, and extensive). We propose multiple seismic fragility curves as functions of a single ground motion parameter and numerous seismic fragility surfaces as functions of two ground motion parameters. The results show that soil type, slope angle, and input ground motion influence these probabilities, and are expected to help regional authorities and engineers assess the seismic fragility of fill slopes in the road systems in South Korea.

• 한국물환경학회지
• /
• 제28권2호
• /
• pp.247-254
• /
• 2012

Soil and Water Assessment Tool (SWAT) model has been widely used in estimation of flow and water quality at various watersheds worldwide, and it has an auto-calibration tool that could calibrate the flow and water quality data automatically from thousands of simulations. However, only continuous measured day flow/water quality data could be used in the current SWAT auto-calibration tool. Therefore, 8-day interval flow and water quality data measured nationwide by Korean Ministry of Environment (MOE) could not be used in SWAT auto-calibration even though long-term flow and water quality data in the Korean Total Maximum Daily Load (TMDL) watersheds available. In this study, current SWAT auto-calibration was modified to calibrate flow and water quality using 8-day interval flow and water quality data. As a result of this study, the Nash and Sutcliffe Efficiency (NSE) values for flow estimation using auto-calibration are 0.77 (calibration period) and 0.68 (validation period), and NSE value for water quality (T-P load) estimation (using the 8-day interval water quality data) is 0.80. The enhanced SWAT auto-calibration could be used in the estimation of continuous flow and water quality data at the outlet of TMDL watersheds and ungaged point of watersheds. In the next study, the enhanced SWAT auto-calibration will be integrated with Web based Load Duration Curve (LDC) system, and it could be suggested as methods of appraisal of TMDL in South Korea.

• 해양환경안전학회지
• /
• 제15권2호
• /
• pp.79-89
• /
• 2009

본 논문은 수산자원보호구역의 효과적이고 합리적인 관리방향에 대한 정책수립 지원라 체계적인 어장환경실태조사 시스템 구축을 위한 사전 진단적 연구접근으로서 수산자원보호구역에서 계절별로 장기적으로 모니터링된 국가해양환경측정망 등의 자료를 이용해서 어장환경의 실태와 변화를 분석하고 평가하였다. 어장환경은 오염이 진행되었거나 진행 중인 것으로 진단되었는데, 각 영역별로 수질과 저질 오염특성이 다소 다르게 나타나서 오염원과 이용실태 및 지형적 특성 등 제반 환경요소를 고려한 맞춤형 수질관리방안 수립이 요구되었다. 또한, 보호구역의 지정면적은 점차적으로 변화되어 왔는데, 2003년도와 처음 시정시의 면적을 비교해 볼 때, 총 면적변화는 $-22.9{\sim}2.4%$ 범위로 완도 도암만은 약 2.4% 정도 미미한 증가를 보였지만, 전체 구역은 평균 약 6.4%가 감소하였고, 한산만이 가장 큰 비율로 감소하였다. 전체 면적 중 육역이 약 6.1%, 해역이 약 6.6%가 감소되었지만, 2008년 시 군별로 고시된 상황을 종합적으로 고려하면 지정면적의 감소는 대부분 육역인 것으로 사료 되었다. 보호구역의 환경을 양호하게 유지하고 효과적인 관리정책을 수립하기 위해서는 실효적인 수질관리방안 뿐만 아니라 개발 및 이용실태 파악을 위한 조사와 데이터(정보)관리가 체계적으로 이루어지고 해역별로 종합 관리할 필요가 있을 것이다. 아울러 각종 관련 법률을 정비 보완해서 조사, 평가, 협의 등 관리방향과 관련된 요소를 일관성있고 체계적으로 정립할 필요가 있다고 판단된다.

• 환경영향평가
• /
• 제32권6호
• /
• pp.503-515
• /
• 2023

개발 과정에서 발생하는 생태공간의 단절과 파편화는 생물다양성의 위협 요소이다. 특히 개발 압력이 높은 도심은 생태공간이 부족하여 연결성이 매우 낮을 것이다. 이러한 문제는 대도시에서 더욱 두드러지게 나타나는 경향이 있다. 이를 해결하기 위해 개별 사업이나 도시관리 수준에서 생태적 연결성 현황을 파악하고 개선하는 지속적인 노력이 필요하다. 그러나 대도시의 생태적 연결성 현황 파악과 개선에 대한 논의가 부족한 실정이다. 따라서 본 연구는 우리나라 대도시 서울, 부산, 대구, 인천, 광주, 대전, 울산의 도심이 가진 생태적 연결성을 평가하였다. 평가 결과 도심은 외곽이나 도시 전체와 비교해 연결성이 낮았다. 그리고 종분포모델 등 지역 특성을 반영하여 대전을 대상으로 수행한 생태적 연결망을 분석하여 1ha 이상 산림을 이어주는 최적 경로 510개를 도출하였다. 본 연구는 도시의 생태적 연결성 개선 목표 제시에 필요한 정량적 수치와 생물다양성을 포함한 지역 특성에 따른 연결망을 도출한 사례로서 의미가 있다. 환경영향평가나 도시관리에서 생태적 연결성을 개선하는 방향을 제시하고 평가 체계를 구축하는 데 결과를 활용할 수 있을 것으로 기대된다.

• 한국환경복원기술학회지
• /
• 제16권1호
• /
• pp.147-157
• /
• 2013

Rice is a main crop and rice field is the most important farmland in Korea. This study was conducted to propose the methodology assessing impact and vulnerability on rice production by climate change at the regional and national level in Korea. We evaluated a vulnerability of rice paddy according to the outbreak of a main disease and pest of a rice plant. As results, Jeju-do, Gyeongsangnam-do, and Jeollanam-do were more vulnerable area than others. In contrast, the southern central region including Gyeonggi-do was less vulnerable than others. The vulnerable index was significantly higher in 2050s (0.5589) than in present (0.3500). This result showed that the vulnerable to the disease and pest enlarge in the future. The adaptive capacity highly contributed to the vulnerability assessment index. The daily maximum temperature of June and the daily average temperature from May to August also contributed the climate exposure index. The area of occurring sheath blight, rice leaf blast and striped rice borer was related to the system sensitivity index. The ability of water supply (readjustment area of arable land per paddy field area) and rice production technique (rice yield per hectare) were the highly contributed variables to the adaption capacity index.

• 한국산업보건학회지
• /
• 제28권2호
• /
• pp.230-239
• /
• 2018

Objective: The purpose of this study is to identify the kinds and exposure levels of health hazards in the metalworking process in relation to acute poisoning accidents caused by methanol in 2016. Methods: The number of industries, workplaces, exposed workers, regional distribution, and exposure level of health hazards in metalworking process were investigated based on employee exposure assessment database provided by KOSHA (the Korea Occupational Safety and Health Agency), which was collected from workplace hazard evaluation programs in Korea. Exposure metrics for methanol were assessed by RCR (risk characterization ratio). Results: The numbers of processes, workplaces, and exposed workers of metalworking, which include CNC (computer numerical control) were 25, 14,405, and 169,102 respectively. The numbers of samples of chemical hazards including methanol were 91,325, and it was found that workers in metalworking were exposed to 249 kinds of chemical hazards. There were 16 kinds of special controlled substances including beryllium. It is estimated that the number of workplaces involving CNC process was 2,537, and the number of exposed workers was 27,976. In CNC process, the total number of workplaces handling methanol was 36, and 298 workers were estimated to be exposed. There was no exceeded that surpassed the OEL and 49% of samples were below the limit of detection. Methanol exposure concentrations in Gyeonggido Province were statistically significantly higher than in other areas (p <0.0001). Conclusions: In the metalworking process including CNC, there is exposure to a wide variety of health hazards. There was no sample exceeding the OEL for methanol. Therefore, it is necessary to recognize the limits of the employee exposure assessment system and urgently improve measures to prevent the occurrence of events like methanol poisoning.