• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.8
• /
• pp.1362-1368
• /
• 2016

This paper proposes the improved transition scheme for a sensorless drive of an interior permanent magnet synchronous motor (IPMSM). In order to operate the IPMSM, the current controller can be used until 300 rpm for the initial operation. After that, the control method of IPMSM is changed to the speed controller for the sensorless control method. At that point, the rotor speed overshoot is generated due to the rapid change of the current reference for the speed controller. The proposed algorithm is able to reduce the overshoot of a rotor speed by compensating the estimated feedforward value to the speed controller. The feedforward value of the current reference is estimated by using a coordinate transformation and is approximated to the current reference after the transition of the control mode. The effectiveness of the proposed scheme is verified by experiments using an IPMSM drive system.

• Journal of Sensor Science and Technology
• /
• v.22 no.6
• /
• pp.404-409
• /
• 2013

We devised calibration procedure for industrial thermometers by a comparison method at the boiling point of nitrogen (${\sim}-196^{\circ}C$). The uncertainty of the calibration was 4 mK (k = 2). As experimentally demonstrated in this work, the effect of the atmospheric pressure on the boiling point of nitrogen can be easily detected by the thermometer. Therefore, when the boiling point of nitrogen is used for calibration of thermometer by comparison, either a reference thermometer must be used to provide the reference temperature or the effect of atmospheric pressure should be carefully considered. The use of a copper block with a large thermal mass soaked into the liquid nitrogen was proven to be more reliable, and the stability of the temperature immersed into the copper block was 1.4 mK. The temperatures at the thermometer wells, evaluated by the crossed-measurement method to compensate for the inaccuracy of the thermometers and the linear drift of the temperature of the copper block, were equivalent within 0.23 mK of standard uncertainty.

• Journal of the Society of Disaster Information
• /
• v.17 no.1
• /
• pp.10-24
• /
• 2021

Purpose: The purpose of this study is to determine the dangers of biodiesel and general diesel mixtures currently used as alternative fuels by equipment (tag method and penski Marten method) and to determine the difference between flash point and combustion point (closed, open) according to test methods. It is intended to be used as a reference material for identification and evaluation of firecausing substances by confirming the risk of mixtures by comparative analysis and measurement, and establishing a risk assessment method for chemical substances. Method: Flash point test method and result treatment were tested based on ASTM and KS M mode, which are tag sealing and pen schematense test methods used as flash point and combustion point test methods for crude oil and petroleum products. The manufacturer of the equipment used in this experiment was a test equipment that satisfies the test standards of KS M 2010 with equipment produced by TANAKA of Japan. The flash point and combustion point were measured, and the flash point according to the test method of biodiesel and general diesel mixture ( Closed, open), and the ignition point of a mixture of biodiesel and general diesel was compared and analyzed for ignition risk compared with conventional diesel. Results: Looking at the experimental results, first, as an analysis of the risk of flammability of the mixture, the flash point of a substance containing 70% biodiesel was found to be about 92℃ based on general diesel with a flash point of 64.5℃, and gasoline and biodiesel or When the biodiesel mixture was synthesized, it was confirmed that the flash point tends to decrease. In addition, the difference between the flash point and the combustion point was analyzed as about 20 ~ 30℃, and when a small amount of gasoline or methanol was mixed, the flash point was lowered, but it was confirmed that the combustion point was similar to that of the existing mixture. Conclusion: In this study, in order to secure the effectiveness of the details of the criteria for judging dangerous materials in the existing Dangerous Materials Safety Management Act, and to secure the reliability and reproducibility of the judgment of dangerous materials, we confirm the criteria for judging the risk of the mixture through an experimental study on flammable mixtures. It will be able to provide reference data for experimental criteria for flammable liquids that are regulated in the field. In addition, if this study accumulates know-how on experiment by test method, it is expected that it can be used as a basis for research on risk assessment and research on dangerous goods.

• Journal of Korean Medical classics
• /
• v.25 no.4
• /
• pp.105-113
• /
• 2012

Objectives : Acquiring information from symptoms is one of the important method to gain clinically available information in korean medicine. Therefore, up to now, study of symptom terms was frequently implemented in promotion of various information project. In data extraction methods using symptom information from DB, information search using synonym and method using ontology is studied and utilized. However, considering concept of symptom has essential information of appeared body area and phenomenon we think that extending synonym and ontology relationship in symptom terms can be useful for search and set to this study. Methods : We collect terms relevant to human body area and structure described in Donguibogam. Synonymous relationship between collected terms is organized. Relationship between collected terms is build to human-body-knowledge table which has form of Concept+Relation+Concept. Type of relationship is limited on a range of expressing content about parts of human body. Result & Conclusion : Search condition is generated automatically using relationship of the upper area in knowledge table contents. Information of next and previous acupuncture point, upper and lower acupuncture point, left and right acupuncture point can be searched using information of acupuncture point location, order, relative position in area, direction in knowledge table contents.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.9B
• /
• pp.1697-1703
• /
• 1999

In this paper, we propose the fast block matching algorithm with half pel accuracy using the lower bound of mean absolute difference (MAD) at search point of half pel accuracy motion estimation. The proposed method uses the lower bound of MAD at search point of half pel accuracy which calculated from MAD's at search points of integer pel accuracy. We can reduce the computational complexity by executing the block matching operation only at the necessary search point. The points are selected when the lower bound of MAD at that point is smaller than reference MAD of integer pel motion estimation. Experimental results show that the proposed method can reduce the computational complexity considerably and keeping the same performance with conventional method.

• Journal of KIISE
• /
• v.44 no.6
• /
• pp.643-648
• /
• 2017

Among Wi-Fi based indoor positioning systems, fingerprinting localization is the most common technique with high precision. However, construction of the initial radio map and the update process require considerable labor and time effort. To address this problem, we propose an efficient method that constructs the initial radio map at each vertex based on a graph. In addition, we introduce a method to update the radio map automatically by mapping signal data acquired from users to the reference point created on each edge. Since the proposed method collects signal data manually only at the vertex of the graph to build the initial radio map and updates it automatically, our proposed method can dramatically reduce labor and time effort, which are the disadvantages of the conventional fingerprinting method. In our experimental study, we show validity of our radio map update method by comparing with the actual reference point data. We also show that our proposed method is able to construct the radio map with an accuracy of about 3.5m by automatically updating the radio map.

• Proceedings of the KIPE Conference
• /
• 2003.07b
• /
• pp.560-564
• /
• 2003

This paper proposes a simple control strategy based on the discontinuous PWM(DPWM) to balance the DC-link voltage of three-level Neutral-Point-Clamped(WPC) inverters at low modulation index. New DPWM methods in multi-level inverter are also introduced. The proposed DPWM method changes the path and duration to flow the neutral point current out of or into neutral point of the DC-link and it makes the overall fluctuation of the DC-link voltage zero during a sampling time of reference voltage vector. Therefore, the voltage of the DC-link can be balanced fairly well and also the voltage ripple of the DC-link is reduced significantly. Moreover, comparing with conventional methods, the proposed strategy is very simple. The validity of the proposed DPWM method is verified by experiment

• International Journal of Aeronautical and Space Sciences
• /
• v.8 no.1
• /
• pp.66-78
• /
• 2007

A multi-point aerodynamic shape optimization technique has been developed for helicopter rotor blades in hover based on a continuous adjoint method on unstructured meshes. The Euler flow solver and the continuous adjoint sensitivity analysis were formulated on the rotating frame of reference. The 'objective function and the sensitivity were obtained as a weighted sum of the values at each design point. The blade section contour was modified by using the Hicks-Henne shape functions. The mesh movement due to the blade geometry change was achieved by using a spring analogy. In order to handle the repeated evaluation of the design cycle efficiently, the flow and adjoint solvers were parallelized based on a domain decomposition strategy. A solution-adaptive mesh refinement technique was adopted for the accurate capturing of the wake. Applications were made to the aerodynamic shape optimization of the Caradonna-Tung rotor blades and the UH-60 rotor blades in hover.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.4
• /
• pp.729-736
• /
• 2013

Power grids are large complicated networks in use around. An absolute phase value for a particular unknown-phase line at a local site should be identified for the operation and management of a 3-phase distribution network. The phase shift for a specific point in the line, as compared with a phase reference point at a substation, must be within a range of ${\pm}60^{\circ}$ for correct identification. However, the phase shift at a particular point can fluctuate depending on the line constants, transformer wiring method, line length, and line amperage, etc. Conducted in this study is a theoretical formulation for the determination of phase at a specific point in the line, Simulink modeling, and analysis for a distribution network. In particular, through evaluating the effects of unbalanced current loads, the limitations of the present phase identification methods are described.

• Journal of the Korean Society of Safety
• /
• v.30 no.4
• /
• pp.99-105
• /
• 2015

In this study, displacement estimation algorithm, which is not requiring an absolute reference point unlike the conventional displacement measurement method, is developed using the geophone. To estimate displacement of the bridge, measured velocity time signal is integrated in the frequency domain. And, the estimated displacement is compared with the measured result using a conventional method. Based on the dynamic field test results, it was found that the estimated displacement by the present algorithm is similar to that of a conventional method. The displacement estimation algorithm proposed in this paper can be effectively applied to measure the displacement of a structure, which is difficult to install a displacement transducer at the fixed point.