• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.1924-1929
• /
• 2010

In long tunnel If we reduce the length of system height on catenary system, tunnel construction cost is cut down. It is because of tunnel section curtailment. So that we have review reduction of system height according to tunnel section. We have designed reduction of system height considered characteristics of overhead contact systems within UIC 799 code.

• 복합신소재구조학회 논문집
• /
• 제4권3호
• /
• pp.7-12
• /
• 2013

The demand for the structural system of reduction of story height increases because buildings are getting higher. The existing structural systems are not efficiency. Thus, it is hard to reduce the story height and existing methods cannot secure economics as expected. This study aims at developing the partially concrete-filled new type composite beam, which can efficiently resist against the end negative moment and central positive moment, also reduce deflection of beams. Through case studies on loading of concentrated load and uniformly distributed load to fixed beam, we could find the most efficient ratio of moment of inertia and the ratio ${\alpha}$(end beam length to span). The gap space between middle and end beam can be used as facilities installation, consequently the suggested Omega beam system is expected to get the effect of reduction in story height as well as reduction of quantity.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.114-117
• /
• 2009

In this work, closing behavior of the voids generated in a casting process was investigated for various parameters such as reductions in height void size and billet rotation during hot open die forging process. The reduction in height and path schedule including the number of paths and billet rotation were chosen as key process variables to express the change of geometrical void shape and void closing behavior. On the other hand, values of die overlapping and die width ratio were set to be constant. Extend of void closure was observed and evaluated using tensile test and microscope. Based on the experimental result, it is ensured that void closure do not occur at 15% and 30% reduction in height as well as one or two rotations of a billet. The useful datum obtained from this study could be utilized to establish an optimum path schedule in the open die forging process.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.160-167
• /
• 2008

The effects of squealer rim height on three-dimensional flows and aerodynamic losses downstream of a high-turning turbine rotor blade have been investigated for a typical tip gap-to-chord ratio of h/c=2.0%. The squealer rim height-to-chord ratio is changed to be $h_{st}/c$=0.00(plane tip), 1.37, 2.75, 5.51, and 8.26%. Results show that as $h_{st}/c$ increases, the tip leakage vortex tends to be weakened and the interaction between the tip leakage vortex and the passage vortex becomes less severe. The squealer rim height plays an important role in the reduction of aerodynamic loss when $h_{st}/c{\leq}2.75%$. In the case of $h_{st}/c{\geq}5.51%$, higher squealer rim cannot provide an effective reduction in aerodynamic loss. The aerodynamic loss reduction by increasing $h_{st}/c$ is limited only to the near-tip region within a quarter of the span from the casing wall.

• 대한족부족관절학회지
• /
• 제11권2호
• /
• pp.226-231
• /
• 2007

Purpose: To evaluate the clinical outcomes and radiographic results of open reduction and internal fixation for intraarticular calcaneal fractures. Materials and Methods: We reviewed 20 cases of calcaneal fractures managed with open reduction and internal fixation from March 2003 to January 2005. We used the computed tomographic classification system proposed by Sanders et al to classify these fractures. Preoperative and postoperative Bohler's angle, heel height (calcaneal facet height) and calcaneal length, calcaneal width were measured. The Creighton-Nebraska Health Foundation Assessment score was used for clinical evaluation. Results: There were 12 cases of type II fractures, 5 of type III fractures and 3 of type IV fractures. The mean clinical score was 84.3 for type II, 82.6 for type III and 56.1 for type IV. The mean preoperative $B{\ddot{o}}hler$ angle was $6.1^{\circ}$ and final was $22.8^{\circ}$. The mean preoperative calcaneal facet height was 76.6 mm and final was 80.3 mm (The mean calcaneal facet height was changed from preop 76.6 mm to postop 80.3 mm). The mean preoperative calcaneal length was 88.2 mm and final was 92.6 mm. The mean preoperative width was 38.1 mm and final was 35.6 mm. Conclusion: Open reduction and internal fixation showed good results for type II and III fractures, but for type IV fractures the clinical result was significantly worse than the other types. However, type IV fractures still had restoration of (should be restored in) $B{\ddot{o}}hler's$ angle, calcaneal facet height, calcaneal length and width which may be helpful in later subtalar fusion.

• 한국방재학회 논문집
• /
• 제9권1호
• /
• pp.145-150
• /
• 2009

댐과 같은 대규모 수리구조물의 신설이 점차 어려워짐에 따라, 이에 대한 대안으로 천변저류지의 설치가 검토되고 있다. 천변저류지는 규모가 작은 시설물로 홍수량, 유입수문곡선, 천변저류지 용량 및 월류위어의 월류고 등에 따라 홍수저감효과가 민감하게 반응한다. 따라서 최대의 홍수저감효과를 얻기 위해서는 홍수저감효과를 기대하는 홍수사상에 적합한 월류고를 적용하여야 하며, 본 연구에서는 월류고 값의 변화가 천변저류지군의 홍수저감효과에 미치는 영향을 분석해보았다. 이를 위해 천변저류지의 최적위치를 결정하기 위해 개발된 기존의 의사결정모형을 사용하였다. 천변저류지의 위치를 결정변수로 사용하고 홍수저감목표 지점에서의 홍수저감효과를 최대화하는 과정을 통해 천변저류지의 최적위치를 결정하는 의사결정모형에 월류고의 높이를 결정 변수로 추가하여 수정하였다. 제안된 모형을 안성천 유역에 적용하여 기존의 연구결과와 비교하였으며, 모형의 적용결과 대상 홍수사상에 대해 보다 효율적인 홍수저감이 가능토록 하는 월류고 및 위치를 결정 할 수 있었다.

• 한국방재학회 논문집
• /
• 제3권2호
• /
• pp.139-145
• /
• 2003

본 연구에서는 다양한 크기의 원환에 따른 균등원통교각 주위의 세굴심을 분석하여 세굴심 감소효과 및 원환의 적정 크기를 제시하였다. 이를 위하여 수리모형실험을 실시하였으며, 교각에 원환을 설치한 경우 원환을 하상 위보다 하상 아래에 설치하는 것이 더욱 효과적이었으며, 원환의 크기가 클수록 세굴심 감소 효과가 뚜렷하였다. 교각 직경에 대한 원환 직경의 비(W/D)가 2인 경우 약 67% 세굴심이 감소하였으며, 퇴적고는 약 70%정도 증가하였다. 세굴심 감소 효과, 세굴공 및 퇴적고의 분석 결과를 토대로 W/D=2인 원환을 최적 크기로 제안하였다.

• 한국광학회지
• /
• 제22권3호
• /
• pp.129-133
• /
• 2011

2-파장 홀로그래피에서 수정된 화인 맵을 이용하여 2-파장 홀로그래피에서 발생하는 잡음 증폭현상을 줄이는 연구를 수행하였다. 일반 적인 화인 맵은 측정체의 단차가 2-파장 홀로그래피에 사용되는 광원의 파장보다 작은 경우에는 잡음을 잘 줄일 수 있으나, 단차가 파장 보다 큰 경우에는 측정 결과에 영향을 주어 잘못 된 측정 결과를 보인다. 이러한 오차를 줄이기 위하여 수정된 화인 맵을 이용하였으며, 그 결과 측정체의 단차가 파장 보다 큰 경우에도 측정에 영향을 주지 않고 잡음을 줄일 수 있음을 확인 하였다.

• 한국도로학회논문집
• /
• 제17권5호
• /
• pp.19-24
• /
• 2015

PURPOSES : The noise, which is typically generated by fast moving vehicles, can be intercepted by installing a noise barrier with a soundproof panel. However, reflections from the panels cause secondary noise, and hence lower the effectiveness of the panels. In this study, the reduction of reflection noise by considering the shape, especially zigzag one, of the soundproof panel have been evaluated. METHODS : The simulation model used in this study was Nord2000, which simulates real-road situations effectively. Based on the simulation results, the joining angle of $133^{\circ}$ with the pattern width (a) equal to 2 m and the projection height (b) equal to 0.5 m was adapted in the zigzag shape as the best profit designing factors. RESULTS: The measuring results at middle height, 15 m showed reduction at all points except the point with average -1.6 dB. At a greater height of 30 m, 2 points showed reduction. A real-sized facility was constructed to investigate the reflected sound from a zigzag shaped panel up to the height of 5 m. CONCLUSIONS: The reduction effects were detected in all the receive points in the range of 2-6 m distances and 1-5 m heights comparing the plane panel. Compared to plane panel, the noises are reduced at an average of 2.4 dBA.

• Korean Journal of Chemical Engineering
• /
• 제35권11호
• /
• pp.2321-2326
• /
• 2018

We evaluated the optimal conditions for fluidization of nickel oxide (NiO) and its reduction into high-purity Ni during hydrogen reduction in a laboratory-scale fluidized bed reactor. A comparative study was performed through structural shape analysis using scanning electron microscopy (SEM); variance in pressure drop, minimum fluidization velocity, terminal velocity, reduction rate, and mass loss were assessed at temperatures ranging from 400 to $600^{\circ}C$ and at 20, 40, and 60 min in reaction time. We estimated the sample weight with most active fluidization to be 200 g based on the bed diameter of the fluidized bed reactor and height of the stocked material. The optimal conditions for NiO hydrogen reduction were found to be height of sample H to the internal fluidized bed reactor diameter D was H/D=1, reaction temperature of $550^{\circ}C$, reaction time of 60 min, superficial gas velocity of 0.011 m/s, and pressure drop of 77 Pa during fluidization. We determined the best operating conditions for the NiO hydrogen reduction process based on these findings.