• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.10
• /
• pp.1035-1040
• /
• 2004

The vibration of an electric hand grinder originates from the motor, gear, bearing, and fan. Its excessive vibration can be harmful to workers. To reduce the vibration of an electric hand grinder. frequency analysis for the vibration signals of a running electric hand grinder and modal test for the each part were done. The results show that the vibration is due to the resonance of the case. To remove the resonance, the case structure was modified and the bearing cap was replaced on a basis of the results of the rotor dynamic analysis using SAMCEF. As a result, the vibration of the electric hand grinder was reduced greatly.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.585-588
• /
• 2013

Electric motor with reduction gear systems are being adopted recently as main propulsion on the special-purposed ships. These specialized ships or offshore vessels require higher power rating generators for propulsion and accommodation power supply. This study investigated the cause of exciter components failure in the view of excessive vibration, force or abnormal ship motion in service. Countermeasures are proposed to address the exciter component failure. A 1.4 MW class dual-fuel engine generator using rigid foundation for a LNG carrier was used as research model.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.1056-1061
• /
• 2004

The vibration of rotor systems is caused by various factors, such as misalignment, unbalance, gear meshing, error of assembly, etc. Modal test and TDA/ODS analysis were done. The dynamic analysis of the armature was done with SAMCEF which is a commercial software for finite element and kinematic analysis. The transient response of the armature is calculated by the SAMCEF with the consideration of magnetic force and bearing stiffness, which are the essential elements for the design of high speed cutter. Main frequency of the vibration is due to the unbalance of the armature. The FEM analysis model considering unbalance and the high speed cutter have same vibration properties. The vibration sources of the high speed cutter is proved to be unbalance.

• Journal of KSNVE
• /
• v.4 no.3
• /
• pp.319-325
• /
• 1994

The flucturation of the engine torque appears to be the major source of the torsional vibration of the automotive driveline. The reduction of this torsional vibration has become a significant problem, due to an increase in the flucturation of the torque of recent light weighted powered engines, along with the requirements of higher performance. The torsional vibration of the automotive driveline can be reduced by soothing the fluctuation by adjusting the torsional characteristics of the clutch-disc. Computer simulation of the engine- input gear train is a useful investigative tool on studying the torsional characteristics of the clutch-disc. In this paper, a dynamic model for the automotive driveline was developed, and the engine torque and drag torque of the model were evaluated withe experimental data. By executing a simulation using the model, it has become possible to obtain the clutch-disc torsional characteristics when the engine is idling and the clucth-disc torsional characteristics for reducing the torsional vibration has been suggested.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.3
• /
• pp.234-239
• /
• 2013

There are many types of speed reducer for industrial uses. However the cycloid speed reducer is widely used in manipulators based on excellent performance of low backlash, high reduction ratio and compact size. It is essential to use precision speed reducer for accuracy of position controls on robot systems and electric vehicles. The cycloid speed reducer has a eccentric rotating motion and offset to avoid some problem of assembly, so it has a disadvantage for vibration. In this paper, a multi-body dynamic model is developed for a cycloid speed reducer and the dynamic behaviors of the reducer are investigated. The cycloid speed reducer consists of cycloidal plate gears, housing gear, input shaft, output pin and shaft, and eccentric bearings. Using a CAD program, each component of cycloid reducer is modeled based on the offset and eccentric. Multi-body simulations using Recurdyn and test using a rig tester are performed. As a result, the pin reaction force and the amplitude of housing displacement are increased by the larger offset and smaller eccentric value of cycloid reducer.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.12
• /
• pp.15-21
• /
• 2019

The worm reducer is capable of quadrature power transmission when the shafts are disposed at right angles to each other. Since a large reduction ratio can be obtained of up to approximately 1/100 and a sliding movement is performed during operation compared with other gears, the noise and vibration are small, and there is the advantage that reverse rotation can be prevented. On the other hand, severe wear and damage are displayed on the gear and worm tooth surface, and many defects, such as intense heat generation of the reducer, occur. In the reducer case, the four-piece casing method was selected to solve the problems of heat generation, transmission efficiency, and assemblability. In this paper, we analyzed the problems of the worm and worm wheel (the core parts of a 5-Ton worm reducer) and casing through these methods and researched how to solve them.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.6
• /
• pp.911-915
• /
• 2017

Recently, there has been an increasing interest in the non-contact power transmission method of magnetic gears. Since there is no mechanical contact, noise caused by friction can be reduced, and even if a sudden large force is applied, the impact of the gear is close to zero. Further, since the power is transmitted by the magnetic flux, it has high reliability. However, there is a problem that a loss due to a magnetic field due to use of a magnetic flux. The loss caused by the magnetic field of the magnetic gear is a joule loss called eddy current loss. In addition, the eddy current loss in the magnetic gear largely occurs in the permanent magnet, but it is a fatal loss to the permanent magnet which is vulnerable to heat. Particularly, magnetic gears requiring high torque density use NdFeB series permanent magnets, and this permanent magnets have a characteristic in which the magnetic force decreases as temperature increases. Therefore, in this paper, the eddy current loss of the permanent magnet according to the permanent magnet attaching method is analyzed in order to reduce the eddy current loss of the permanent magnet. We have proposed a structure that can reduce the eddy current loss through the analysis and show the effect of reducing the loss of the proposed structure.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.6
• /
• pp.1529-1534
• /
• 2008

Recently, mixers are being widely used in the display and semiconductor company in order to mix the chemical materials. The mixer normally consists of shaft, hub, reduction gear, and driving motor. It is one of the key design factors to evaluate the dynamic characteristics caused by the rotation. In this study, the dynamic characteristics of the high speed mixer, such as vibration, noise and thermal radiation, are verified by the experiment. Through the experiment, it is shown that the structural unbalance mass of high speed mixer is the important source of the severe vibrations and maximum temperature is mixer bowl.

• Journal of KSNVE
• /
• v.8 no.5
• /
• pp.929-935
• /
• 1998

Safety diagnosis of electric train driving system is performed using vibration signals of running electric train. Safety diagnosis is tried on the viewpoints of the appreciation of superannuation and the fault diagnosis of motor, reduction gear and bogie. The appreciation of superannuation is checked by the vibration levels of driving parts and the fault diagnosis is done by analyzing the frequencies of the vibration signals which are measured directly from a running electric train. The results shows that the vibration levels of each parts increase as the train gets older and each parts have their own frequency patterns of the vibration. Vibration propagation path is also investigated using calculated the coherence value between bogie and driving system. As the results, it is known that vibration signal can be utilized successfully for the safety diagnosis of the driving part of electric train.

• Journal of Mechanical Science and Technology
• /
• v.20 no.10
• /
• pp.1626-1637
• /
• 2006

The pressure pulsation due to the gear geometry of the gerotor (generalized rotor) pump mainly occurs in an instant that the chamber of the gerotor enters the delivery port and leaves the suction one. Such a pressure pulsation may result in undesirable vibration and noise of pump components as well as cavitation in hydraulic system. Therefore, it is very important to examine the pressure characteristic of the gerotor pump at its design and analysis stages. In this paper, in order to reduce the pressure pulsation in the gerotor pump, the port plate with the relief grooves is designed by referring to as notch of vane pump and relief groove of piston pump. A series of the theoretical analyses on the pressure pulsation is performed in consideration of various design parameters of the port plate, including the installation positions of the port inlet/outlet and the groove width, and the operating conditions such as rotational velocity and delivery pressure.