• International Journal of Internet, Broadcasting and Communication
• /
• v.15 no.1
• /
• pp.254-261
• /
• 2023

The purpose of this study was to investigate the effects of 8-week resistance training on muscle fatigue in men in their 50s and 30s. A total of 16 subjects (8 in their 30s and 8 in their 50s) were recruited, and moderate-intensity resistance exercise was conducted three times a week for eight weeks. EMG was measured before and after 8 week resistance training. Before 8 weeks exercise, MDF of pectoralis major significantly decreased in all groups, and MDF of triceps brachii significantly decreased only in the 30s group. After 8 weeks of exercise, MDF of pectoralis major significantly decreased in all groups, and MDF of triceps brachii significantly decreased only in the 30s group. The fatigue index before and after the 8-week exercise was changed only in the pectoralis major, and significantly decreased in the 30s group. As a result, the muscle fatigue level among the resistance exercises of men in their 50s may be similar to that of men in their 30s, and muscle fatigue can be reduced by 8 weeks of exercise.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.7
• /
• pp.575-579
• /
• 2010

The technologies of Ni/Cu plating contact is attributed to the reduced series resistance caused by a better contact conductivity of Ni with Si and the subsequent electroplating of Cu on Ni. The ability to pattern narrower grid lines for reduced light shading was combined with the lower resistance of a metal silicide contact and an improved conductivity of the plated deposit. This improves the FF (fill factor) as the series resistance is reduced. This is very much requried in the case of low concentrator solar cells in which the series resistance is one of the important and dominant parameter that affect the cell performance. A Selective emitter structure with highly dopeds regions underneath the metal contacts, is widely known to be one of the most promising high-efficiency solution in solar cell processing In this paper the formation of a selective emitter, and the nickel silicide seed layer at the front side metallization of silicon cells is considered. After generating the nickel seed layer the contacts were thickened by Cu LIP (light induced plating) and by the formation of a plated Ni/Cu two step metallization on front contacts. In fabricating a Ni/Cu plating metallization cell with a selective emitter structure it has been shown that the cell efficiency can be increased by at least 0.2%.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.20 no.1
• /
• pp.50-54
• /
• 1983

Contact resistance variation which may be called sliding noise in carbon film variable resistors whose resistance elements consists of linear resistivity distribution were measured with several kinds of sliders and were analyzed to reduce the contact resistance variation. About the measuring method, the standard method of measuring contact resistance variation specified by the variable Resistance Components Institute was adupted. By analyzing the experimental results, it has been shown that the primary cause of contact resistance variation is due to current constriction and small discharge sparks in the resistance film in the area close to the slide contact. Moreover, it has been found that the sliding noise would be reduced by increasing the number of contact points, sliding speed, and pressure, and by using some kinds of insulation oil on the contacting surface. High contact resistance variation is likely to occur in the area of high resistance variation in a logrithmic resistance taper.

• Journal of Crop Science and Biotechnology
• /
• v.11 no.2
• /
• pp.127-134
• /
• 2008

Tobamoviruses are the major viral pathogens of tomato and bell pepper. The preliminary results showed that Acibenzolar-Smethyl(ASM; S-methylbenzo(1,2,3) thiadiazole-7-carbothiate) pre-treatment to tomato and tobacco plants reduces the concentration of Tomato mosaic tobamovirus(ToMV) and Tobacco mosaic tobamovirus(TMV) in tomato and bell pepper seedlings, respectively. Pre-treatment of the indicator plant(Nicotiana glutinosa) with the ASM followed by challenge inoculation with tobamoviruses produced a reduced number and size of local lesions(67 and 79% protection over control to TMV and ToMV inoculation, respectively). In order to understand the mechanism of resistance the gene expression profiles of antiviral genes was examined. RT-PCR products showed higher expression of two viral resistance genes viz., alternative oxidase(AOX) and RNA dependent RNA polymerase(RdRp) in the upper leaves of the ASM-treated tomato plants challenge inoculation with ToMV. Further, the viral concentration was also quantified in the upper leaves by reverse transcription PCR using specific primer for movement protein of ToMV, as well as ELISA by using antisera against tobamoviruses. The results provided additional evidence that ASM pre-treatment reduced the viral movement to upper leaves. The results suggest that expressions of viral resistance genes in the host are the key component in the resistance against ToMV in the inducer-treated tomato plants.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.2
• /
• pp.75-86
• /
• 2012

This paper presents some research results on the shrinkage characteristics and frost resistance before and after cracking of FR-ECC(Fire Resistance-Engineered Cementitious Composite). Also, a waterstop performance and exfoliating resistance of multi-layer lining specimens using FR-ECC and flexural performance of beam member by repaired FR-ECC are estimated in this paper. Experimental results indicate that the plastic shrinkage crack and length change ratio of FR-ECC have been reduced as compared with that of the existing repair mortar, and that its crack resistance on the dry shrinkage is improved under the confining stress. As well as FR-ECC has been great in the frost resistance and its tensile properties under the cracked state have been not reduced by freezing and thawing reaction. In addition, beam member by repaired FR-ECC have been increased in the flexural properties such as initial crack moment, yeild moment, and its crack width has been controled in a stable by the frexural failure.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.5
• /
• pp.649-659
• /
• 2023

Smart work, which utilizes ICT technology to work without time and space constraints, has been difficult to introduce and spread despite a lot of research and investment based on the 'smart work vitalization strategy' that began in 2010. Although the environment of COVID-19 in 2019 was an opportunity to promote the adoption of smart work. After that, many companies ended or reduced the adoption of smart work again. This study was initiated to examine the factors that resist the introduction of smart work based on the innovation resistance model and to suggest alternatives. As a result of this study, relative advantage showed a strong effect on both introduction resistance and introduction intention. However, it was confirmed that perceived risk and complexity did not directly negatively affect introduction intentions, but had a negative effect on introduction intentions through mediating resistance to introduction. Through the results of this study, it was confirmed that if the practical benefits of smart work were emphasized and negative attitudes were reduced, the resistance to introduction would be lowered and the intention to introduce it would be positively affected.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.266-269
• /
• 2000

This paper presents a novel single-stage unity power factor converter which features the reduced switching losses by zero-voltage switching and zero-current switching (ZVZCS). Hence the turn-on and turn-off losses of switches are sufficiently reduced. And the reduced conduction losses are achieved by the elimination of one leg of front-end rectifier. And low on-resistance MOSFETs (Synchronous Rectifier) are used in the rectifier at the secondary side of high frequency transformer instead of diodes. Theoretical analysis simulated results of a AC to DC 150W(5V, 30A) converter are presented.

• Journal of Crop Science and Biotechnology
• /
• v.11 no.3
• /
• pp.177-180
• /
• 2008

Worldwide, cyst nematode(Heterodera glycines Ichinohe) is the most destructive pathogen of cultivated soybean. In the USA, current annual yield losses are estimated to be nearly a billion dollars. Crop losses are primarily reduced by the use of resistant cultivars. Nematode populations are variable and have adapted to reproduce on resistant cultivars over time because resistance primarily traces to two soybean accessions. It is important to use diverse resistance sources to develop new nematode resistant cultivars. Soybean PI 494182 is a recent introduction from Japan and found to be resistant to multiple nematode populations. It is yellow seeded and maturity group 0. We have determined inheritance of resistance in PI 494182 using $F_{2:3}$ families derived from cross PI 494182 X cv. Skylla. Skylla is a susceptible parent. Three nematode populations, races 1, 3, and 5, corresponding to HG types 2.5.7, 0, and 2.5.7 were used to bioassay 162 $F_{2:3}$ families in greenhouse experiments. Based on Chi-square tests, a two-gene model is proposed for resistance to race 1 and a three-gene model is proposed for conditioning resistance to both races 3 and 5. Correlation coefficient analysis indicated that some genes conditioning resistance to races 1, 3, and 5 are shared or closely linked with each other. These results will be useful to soybean breeders for developing soybean cultivars for broad resistance to nematodes.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.182-182
• /
• 2009

The effect of Re-oxidation on the PTCR properties of Sm-doped barium titanate ceramics was investigated by means of impedance spectroscopy. Electrical properties such as resistance vs. temperature, I-V curve were measured and microstructure was observed with SEM photography. Sample was fabricated with thick film process such as tape casting of green sheet, screen printing of electrode pattern, stacking, firing in reduced atmosphere and re-oxidation, etc. As the temperature of re-oxidation increases, resistance jump as a function of temperature enhances but resistance at room temperature increases. These behavior of resistance as a function of temperature, dependent on the re-oxidation condition, is analyzed with Cole-Cole impedance plot and is shown to be related with the degree of oxidation of grain boundary regardless of grain core during re-oxidation process of sample.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.4
• /
• pp.478-483
• /
• 2011

Cast mold has low wear-resistance comparing with other alloyed molds which result in lower production rate and high cost of products. Recently, various weld methods are being applied to increase the wear-resistance of molds and to extend mold life. Among them, nickel alloy weld process increases the hardness irrelevant to its machinability and creates very uniform structures. In addition, it causes better wear-resistance and reduces shrinkage defects. In this paper, we analyze the mold surface cracks welded by nickel alloy and propose the methods to improve the mold surface and its wear-resistance. It has been found that nickel alloy weld does not affect the inside crack of mold but has an influence on the surface crack seriously. Results show that the start and growth of fatigue cracks have been delayed about 3 times and reduced approximately 75%, respectively, and the mold surface cracks are decreased about 5.7 times.