• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.2
• /
• pp.105-110
• /
• 2011

Through this study, the performance evaluation on the addition of low-pressure loop EGR(Exhaust Gas Recirculation) in a 6.0 L commercial diesel engine was carried out using WAVE modeling and simulation. Since the key technology of advanced diesel engine combustion such as low-temperature combustion is to steadily supply high rates of EGR in a wide operating range, the current study could be effectively contribute to the design and development processes of up-to-date diesel engine systems as real-world reference data. The current simulation results show that the system in which low-pressure loop EGR is added shows almost 2.3 times increase in maximum EGR rate at 1000 rpm as well as almost 1.6 times increase at 2200 and 1600 rpm in comparison with an engine system employing high-pressure loop EGR only. Also, both turbocharger axis speed and charging pressure level did not deteriorate due to the addition of low-pressure loop EGR at 2200 and 1000 rpm, but they were fairly decreased at 1600 rpm.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.6 s.237
• /
• pp.722-729
• /
• 2005

Design analysis of the solid oxide fuel cell and gas turbine combined power system is performed considering different methods for preheating cell inlet air. The purpose of air preheating is to keep the temperature difference between cell inlet and outlet within a practical design range thus to reduce thermal stress inside the cell. Three different methods considered are (1) adopting a burner in front of the cell, (2) adopting a preheater (heat transfer from the main combustor) in front of the cell and (3) using recirculation of the cathode exit gas. For each configuration, analyses are carried out for two values of allowable maximum cell temperature difference. Performance characteristics of all cases are compared and design limitations are discussed. Relaxation of the cell temperature difference (larger difference) is proved to ensure higher efficiency. Recirculation of the cathode exit gas exhibits better performance than other methods and this advantage becomes more prominent as the constraint of the cell temperature difference becomes more severe (smaller temperature difference).

• 한국연소학회:학술대회논문집
• /
• 2003.12a
• /
• pp.89-94
• /
• 2003

For the development of high efficiency and low emission combustion systems, high temperature air combustion technology has been tested by utilizing preheated air over 1100 K and exhaust gas recirculation. In this system, combustion air is diluted with large amount of exhaust gases ($N_2$, $CO_2$), such that the oxygen concentration is relatively low in the reaction zone, leading to low flame temperature. Since, the temperature fluctuations and sound emissions form the flame are small and flame luminosity is low, the combustion mode is expected to be flameless or mild combustion. Experiment was performed to investigate the turbulent flame structure and $NO_X$ emission characteristics in the high temperature air combustion focused on coflowing jet diffusion flames which has a fundamental structure of many practical combustion systems. The effect of turbulence has also been evaluated by installing perforated plate in the oxidizer inlet nozzle. LPG was used as a fuel. Results showed that even though $NO_X$ emission is sensitive to the combustion air temperature, the present high temperature air combustion system produce low $NO_X$ emission because it is operated in low oxygen concentration condition in excess of dilution.

• Transactions of Materials Processing
• /
• v.16 no.8
• /
• pp.621-628
• /
• 2007

Nowadays, Exhaust Gas Recirculation(EGR) Cooler is one of the most favorite systems for reducing the generation amount of $NO_x$ and other particle materials from vehicles burning diesel as fuel. Efficiency of the system is mainly dependent on its heat transfer efficiency and this ability is affected by net heat transferring area of the system. For that reason, several types of heat transfer tube such as dimple, wrinkle and spiral types that have large net area are used. However, it is difficult to manufacture the rectangular tube with dimpled type structure because it experiences too much strain around the rectangular tube surface during the forming process. For that reason, in this study, numerical simulation for forming process of non-symmetric dimple shape on a thin sheet metal was carried out. Furthermore, theoretical forming limit curves(forming limit diagram, forming limit stress diagram) were proposed as criteria of formability evaluation. From the results of finite element simulation in view of stress and strain distribution, it is found that the designed process has robustness and feasibility to safely manufacture the dimpled rectangular tube.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.5
• /
• pp.188-194
• /
• 2005

The direct injection diesel engine is one of the most efficient thermal engines. For this reason DI diesel engines are widely used for heavy-duty applications. But the world is faced with very serious problems related to the air pollution due to the exhaust emissions of diesel engine. So, that is air pollution related to exhaust gas resulted from explosive combustion should be improved. Exhaust Gas Recirculation(EGR) is a proven method to reduce NOx emissions. In this study, the experiments were performed at various engine loads while the EGR rates were set from $0\%$ to $30\%.$ The emissions trade-off and combustion of diesel engine are investigated. The brake specific fuel consumption rate is very slightly fluctuated with EGR in the range of experimental conditions. The ignition delay increased with increasing EGR rate. The maximum value of premixed combustion for the rate of heat release is increased with increasing EGR rate. NOx emissions are decreased with increasing EGR rate at high load and high speed. It was found that the exhaust emissions with the EGR system resulted in a very large reduction in oxides of nitrogen at the expense of higher smoke emissions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.2
• /
• pp.1-8
• /
• 2002

The flow and combustion patterns have been investigated inside the gasoline engine cylinder with the swirl or tumble flow, whereas the air flow characteristics, which are generated in the part of intake system before entering into the intake manifold, have not been known completely. It is necessary to analyze the flow field in the intake system consisting of air rater, throttle valve and intake manifold. The throttle valve, used to control the intake air flow rate, is important because it makes various mass flow rate and flow patterns. Three-dimen-sional How characteristics such as velocities, turbulent intensities and Reynolds shear stresses are measured by the hot wire anemometer at the exit of the throttle valve with the variation in the valve opening angle($15^{\circ}$, $45^{\circ}$, $75^{\circ}$ and $90^{\circ}$) and the Reynolds numbers (45000, 70000 and 140000). There are a lot of changes in flow characteristics at $75^{\circ}$ due to the large recirculation flow comparing with those of the other cases, and the streamwise velocity is especially enforced strongly below the valve shaft. The other component velocities are relatively large near the centerline parallel to the valve shaft. The effects of the Reynolds number on the flow field are not severe.

• KSBB Journal
• /
• v.5 no.1
• /
• pp.69-74
• /
• 1990

Dynamic characteristics of separation in membrane filtration system of tangential flow was investigated to find the functional relationship among the filtrate flux, transmembrane pressure, inulin concentration and recirculation rate. In case that NMWL is 1000, tracts-membrane pressure $0.4kgf/\;{\textrm{cm}^2}$ to $3.2kgf/\;{\textrm{cm}^2}$, inulin concentration lwt% to 5wt%, and recirculation rate 4ml / sec, mathematical model for the function among filtrate flux, transmembrane pressure, and inulin concentration was deduced and expressed as follows.Jv = (0.0022p + 0.0003) ln \frac{3p\;+\;2.1}{C_b}$ The values calculated by the above equation and those measured were compared to find to be nicely in accord with each other. Especially the agreement was enhanced in the region of higher concentration of inulin.

• Journal of Power System Engineering
• /
• v.9 no.3
• /
• pp.15-20
• /
• 2005

In this paper, the effect of oxygen component in fuel on the exhaust emissions has been investigated for an indirect injection diesel engine. It was tested to estimate change of engine performance and exhaust emission characteristics for the commercial diesel fuel and oxygenated blended fuel which has four kinds of mixed ratio. And, the effects of exhaust gas recirculation(EGR) on the characteristics of NOx emission have been investigated. Ethylene glycol mono-n-butyl ether(EGBE) contains oxygen component 27% in itself, and it is a kind of effective oxygenated fuel of mono-ether group that the smoke emission of EGBE is reduced remarkably compared with commercial diesel fuel, that is, it can supply oxygen component sufficiently at higher loads and speeds in diesel engine. It was found that simultaneous reduction of smoke and NOx was achieved with oxygenated fuel(10vol-%) and cooled EGR method(10%).

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.44 no.4
• /
• pp.359-365
• /
• 2011

This study was conducted to investigate the production, elver stocking, rearing facilities and rearing method of eel culture to determine aquaculture management conditions for optimal rearing of eel Anguilla japonica. The production of eel culture was evaluated by the proportion of eels from the main inland fin fish species production in Korea. Elver stocking was assessed by the elver stocking densities of pond and recirculation culture. Rearing facilities were investigated according to the rearing tank size proportion of the pond and recirculation culture. We selected sample farms by region and by size. We visited sample farms and recorded the number of elvers stock for pond area, size of tanks, feed and feed quantity, and the size and number of harvest eels. The production capacity of Jeollanam-do and Jeollabuk-do were 71.9% and 21.3% respectively. This production quantity represented 93.2% of the total Korean eel production quantity. In Jeollanam-do, there are 236 eel farms, 202 pond farms, and 34 recirculation aquaculture facilities. The elvers' first density data by each aquaculture method revealed that elvers' first density varied more in recirculation system farms, as compared to pond aquaculture. In intensive pond farms, the elvers' first density decreased as the size of farm increased. There was a correlation between the size of tank(x) and the facility of a water wheel for dissolved oxygen in pond culture systems(y=0.022x-0.494; $R^2$=0.860). Another strong correlation was found between the weight of eel(x) and eel density(y) in pond culture systems(y=283.5x-0.27; $R^2$=0.992). Finally, there was a strong correlation between the length of eel(x) and the weight of eel(y) in intensive pond culture(y=0.0005x-3.2783; $R^2$=0.9775). The final survival rate did not differ significantly among pond sizes and culture types.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.3
• /
• pp.669-678
• /
• 1994

The BOD removal characteristics of submerged biofilters filled with three kinds of filter media respectively were experimentally examined with constant temperature, pH value and variable BOD loading and recirculation ratio. Obtained results are as follows; 1. The BOD removal ratio decreases with the increasing $BOD_5$ volumetric loading rate, and the loading rate for the BOD removal over 90% is lower thean $1.6kg{\cdot}BOD_5/m^3{\cdot}d$ for the plastic media of Netring and cubic wire meshes. This is a much large value than $0.3{\sim}0.8kg{\cdot}BOD_5/m^3{\cdot}d$ for conventional activated sludge process. The required submerged biofilter volume is found to be much samller than that of conventional activated sludge process. 2. The decreasing order of BOD removal is Netring (random plastic media), cubic wire meshes (plastic module), and then gravel (stone media). This is mainly due to the media characteristics such as void ratio, specific surface area and media shapes. 3. The $BOD_5$ removal rate increases with the recircuration ration, but the rate of increases becomes samaller as the recirculation ratio increases over 20. When $BOD_5$ loading is $1.8kg{\cdot}BOD_5/m^3{\cdot}d$, the required recirculation rationto obtain 90% $BOD_5$ removal is about 20 for Netring and it was about 30 for cubic wire meshes. 4. Reynold's Number increases with recirculation ratio, and the Reynold's Numbers corresponding to the recircuration ratio of 10~50 are less than 52, showing laminar up flows in the filter. The settled and effluent sludges increase with increase of Reynol's Number, and there are the definite Reynold's Numbers at which the settling sludge concentrations become nearly constant respectively in each filters. 5. In this submerged biofilter system, small volume of sludge hopper can be substituted for a separated settling tank.