• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2019년도 추계 학술논문 발표대회
• /
• pp.135-136
• /
• 2019

Recently, as the interest in environmental issues increases, the construction industry needs to recycle blast furnace slag, circulating fluidized bed Combustion fly ash, etc. to solve industrial by-products, and to develop artificial stone. In this study, the strength characteristics based on blast furnace slag according to the addition rate of alkali stimulant NaOH are investigated. The experimental results showed that the flexural and compressive strengths increased with the addition of alkali stimulants. Based on these results, it will be presented as a basic research data for the manufacture of artificial stone and will be tested later.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2007년도 추계 학술논문 발표대회
• /
• pp.87-90
• /
• 2007

The purpose of this study is to investigate the properties of concrete with the kinds and addition of expansive additives. 2 kinds of expansive additives produced in our country and 0, 10, 20, 30, 40% of ratio of addition rate are selected for this experiment. According to experimental results, flow, slump and air rate of concrete with expansive additives is nearly same with its of plain concrete and compressive strength, tensile strength of concrete with expansive additives at 28 days is higher than that of plain concrete. Therefore, The expansion concrete is able to manufactured so it consumes by restricted effects.

• Tribology and Lubricants
• /
• 제5권1호
• /
• pp.12-20
• /
• 1989

The friction and wear behavior of molybdenum disulfide filled polymer composites sliding against metal has been investigated using pin-on-disc machine and microscope. The observed wear rates were reduced by the addition of MoS$_2$ to nylon and this can be attributed to the homogenous transfer of MoS$_2$ to the counteddace thereby modifying sliding conditions. The friction of filled and unfilled nylon was increased with increasing sliding speed, and the catastropic wear rate was occurred at high normal load. This have been explained by thermal degradation. In the case of HDPE, however, the wear rate was not always reduced by the addition of MoS$_2$ and the influence of MoS$_2$ was mainly even the opposite. Filled and unfilled HDPE had lower values of friction and wear rate than those of nylon. Micrographs appeared that the delamination of the worn surface in nylon/MoS$_2$ composite occurred and revealed that the worn surface of HDPE presented a number of characteristic features as wear grooves, pulls, and smears and crescents.

• 한국환경과학회지
• /
• 제7권1호
• /
• pp.74-80
• /
• 1998

Because permeate flux was very low as It has the suspension soled of higher concentration In the trafiltration membrane separation treatment of dyestuff wastewater, pre-treatment of Ponton reaction was carried out. In the case of pH 3, COD removal rate was the hi각erst of 58%. When PAC was added into the pre-treatment supernatant, the COD removal rate was found to be 53% , and when COD was 153mg/L, the removal rate was 92.3% in the trafiltration separation. In addition, the effect of the addition of PAC on the permeate flux was also investigated. The decrease of permeate flux In the presence of PAC was higher than In the abscence of PAC, but the recovery of permeability by cleaning was better In the case of PAC system.

• 한국멀티미디어학회논문지
• /
• 제11권12호
• /
• pp.1730-1738
• /
• 2008

Quality of Service (QoS) Guarantees grant ways for service providers to establish service differentiation among subscribers. On the other hand, service subscribers are also assured the level of service they paid for. In addition, the efficient level of service quality can be selected according to the subscribers' needs thus ensuring efficient use of available bandwidth. While network utility optimization techniques assure certain QoS metrics, a number of situations exist where some QoS goals are not met. The optimality of the network parameters is not mandatory to guarantee specified QoS levels. This paper proposes a joint data rate and power control scheme that guarantees service contract QoS level to a subscriber using Goal Programming. In using goal programming, this paper focuses on finding the range of feasible solutions as opposed to solving for the optimal. In addition, in case no feasible solution is found, an acceptable compromised solution is solved.

• 한국표면공학회지
• /
• 제26권5호
• /
• pp.263-270
• /
• 1993

The effects of surfactants on electorless copper plating bath for PCB was studied. Basic bath composition was cuplic sulfate 10g/l, EDTA.2Na 40 g/l, formalin$ 3m\ell$/l and sodium hydroxide solution for pH adjust. After addition of accelerators, stabilizers and surfactants, the polarization curves in plating bath were carried out for presumption of the plating rate. From the plating rate in bath with the various concentration of additives, the optimum condition for manufacturing the electroless copper plating bath was confirmed. It was found that the addition of $\alpha$.$\alpha$'-dipyridyl, pyridine and polyxyethylene octylphenylether was good as stabilizer, accelerator and surfactants, respectively. With this additives, the maximum plating rate of $12\mu\textrm{m}$/h at $65^{\circ}C$ and $2\mu\textrm{m}$/h at $25^{\circ}C$ was obtained.

• 한국세라믹학회지
• /
• 제26권4호
• /
• pp.550-558
• /
• 1989

Polycrystalline diamond films have been deposited on Si wafer Ly hot W filament CVD method using CH4H2 mixtures. The effects of surface pretreatment, W filament temperature, CH4 volume fraction, and addition of water vapor on the growth rate and morphology of the films were investigated. Surface pretretment was essential for depositing a continuous diamond film. Raising the filament temperature resulted in an increased growth rate and a better crystal quality of the film. As the methane content is varied from 0.5% to 5%, well-faceted crystals gradually transformed into spherical particles of non-diamond phase with a simultaneous increase in the growth rate. Addition of water vapor markedly improved the crystallinity to produce crystalline particles even with 5% methane mixture.

• 한국폐기물자원순환학회지
• /
• 제35권8호
• /
• pp.785-798
• /
• 2018

Since the Framework Act on Resource Circulation was enacted in 2018, the government should establish a National Resource Circulation Master Plan every 10 years, which defines mid- to long-term policy goals and directions on the efficient use of resources, prevention of waste generation and recycling of waste. In addition, we must set mid- to long-term and stepwise targets for the final disposal rate, recycling rate (based on sorted recyclable materials and recycled products), and energy recovery rate of wastes, and relevant measures should be taken to achieve these targets. However, the current industrial waste (IW) statistics have limitations in setting these targets because the final disposal rate and recycling rate are calculated as the ratio of the recycling facility input to the IW generation. In this study, the material flow from the collection stage to the final disposal of industrial waste was analyzed based on the generation of 2016, and the actual recycling amount, actual incineration amount, final disposal amount and their rates were calculated. The effect on the recycling, incineration and final disposal rates was examined by changing the treatment method of nonhazardous wastes from the factory and construction and demolition wastes, which were put in landfills in 2016. In addition, the variation of the waste treatment charge was investigated according to the change of treatment methods. The results of this study are expected to be effectively used to establish the National Resource Circulation Master Plan and industrial waste management policy in the future in South Korea.

• Tribology and Lubricants
• /
• 제37권6호
• /
• pp.253-260
• /
• 2021

Metal pipes are used in a wide range of applications, from plumbing systems of large construction sites to small devices such as medical tools. When a liquid is enforced to flow through a metal pipe, a higher flow rate is beneficial for higher efficiency. Using high pressures can enhance the flow rate yet can be harmful for medical applications. Thus, we consider an optimal geometrical design to increase the flow rate in medical devices. In this study, we focus on cannulas, which are widely used small metal pipes for surgical procedures, such as liposuction. We characterize the internal flow rate driven by a negative pressure and explore its dependence on the key design parameters. We quantitatively analyze the suction characteristics for each design variable by conducting computational fluid dynamics simulations. In addition, we build a suction performance measurement system which enables the translational motion of cannulas with pre-programmed velocity for experimental validation. The inner diameter, section geometry, and hole configuration are the design factors to be evaluated. The effect of the inner diameter dominates over that of section geometry and hole configuration. In addition, the circular tube shape provides the maximum flow rate among the elliptical geometries. Once the flow rate exceeds a critical value, the rate becomes independent of the number and width of the suction holes. Finally, we introduce a slippery liquid-infused nanoporous surface (SLIPS) coating using nanoparticles and hydrophobic lubricants that effectively improves the flow rate and antifouling property of cannulas without altering the geometrical design parameter.

• 한국물환경학회지
• /
• 제23권6호
• /
• pp.837-842
• /
• 2007

This study was conducted to test the effect of residual Al on plankton community after dissolved air flotation (DAF) application. Growth rate of phytoplankton after DAF application ($0.37day^{-1}$) was about 2 times lower than that before DAF application ($0.70day^{-1}$). Under the condition of addition of nitrogen and phosphorus without light, growth rate phytoplankton in treatment without residual Al increased in difference with showing the negative growth rate in treatment with residual Al. Under the condition of light without addition of nutrient, growth rate of phytoplankton was no noticeable difference between the before and after DAF application. The relatively high settling rate (0.47 m/day) was observed in treatment after DAF application. Although the abundance of rotifer decreased, the abundance of copepod and cladoceran such as Daphnia galeata, Diaphanosoma sp. and Bosmina longirostris with relative higher grazing was no noticeable difference between the before and after DAF application. In the treatments before and after DAF application with zooplankton, growth rate of phytoplankton was $0.41{\pm}0.08day^{-1}$, $0.20{\pm}0.03day^{-1}$, respectively. This difference was in treatment after DAF application similar with those in treatments before and after DAF application without zooplankton. Those indicate that the filter-feeding effect of zooplankton on phytoplankton community may be not changed by residual Al after the DAF application. These results suggest that residual Al after DAF application be to improve water quality by inhibition of growth rate as well as increasing settling rate of phytoplankton.