• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.3 s.234
• /
• pp.390-401
• /
• 2005

In this study, extinction limit extension of unsteady $(CH_{4}+N_{2})$/air diffusion flames was investigated experimentally. A spatially locked flame in an opposing jet burner was perturbed by linear velocity variation, and time-dependent flame luminosity, transient maximum flame temperature and OH radical were measured over time with the high speed camera, Rayleigh scattering method and OH laser-induced fluorescence, respectively. Unsteady flames survive at strain rates that are much higher than the extinction limit of steady flames, and unsteady extinction limits extend as the slope of the strain rate increases or the initial strain rate decreases. We verified the validity of the equivalent strain rate concept by comparing the course of unsteady extinction process and steady extinction process, and it was found that the equivalent strain rate concept represents well the unsteady effect of a convective-diffusive zone. To investigate the reason of the unsteady extinction limit extension, we subtracted the time lag of the convective-diffusive zone by using the equivalent strain concept. Then the modified unsteady extinction limits become smaller than the original unsteady extinction limits, however, the modified unsteady extinction limits are still larger than the steady extinction limits. These results suggest that there exist the unsteady behavior of a diffusive-reactive zone near the extinction limit due to the chemical non-equilibrium states associated with unsteady flames.

• Journal of the Korean Society of Safety
• /
• v.5 no.2
• /
• pp.58-65
• /
• 1990

The purpose of this study is to consider the effects of strain rate on the stress-strain behavior of sheet metal at instability. The results and conclusions obtained as follows ： 1. As the strain rate increases, the fracture pressure increases and the polar height at fracture decreases. 2. The effect of strain rate on forming limit diagram produces a general lowering of the diagram with increasing strain rate but changes according to materials and strain paths. 3. The forming limit diagram predicted by swift instability theory is comparatively inconsistent with the experimental result at high strain rates, because there is inevitable gap between them.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.285-288
• /
• 2009

The purpose of this study is to predict the forming limit diagram (FLD) of strain-rate sensitive materials on the basis of the Marciniak and Kuczynski (M-K) theory. The strain-rate effect is taken into consideration in such a way that the stress-strain curves for various strain-rates are inputted into the formulation as point data, not as curve-fitted models such as power function. Tensile tests and R-value tests were carried out at several levels of temperature and strain-rate from $25^{\circ}C$ to $300^{\circ}C$ and 0.16 to 0.00016/s, respectively to obtain the mechanical properties of AZ31B magnesium alloy sheet. The FLD of this material was experimentally obtained by limit dome height tests with the punch velocity of 0.1 and 1.0 mm/s at $250^{\circ}C$. The M-K theory-based FLD predicted using Yld2000-2d yield criterion was compared with the experimental results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.698-698
• /
• 2014

According to the analysis of special medical examination and work environment monitoring data, the rate of C1 and D1 on noise hazard exceeded 90% among those of total hazardous factors. The rate of company exceeding noise exposure limit was also more than 90%. The analysis result shows that main ages diagnosed with C1 and D1 was age of 50s. The majority scale company having workers diagnosed with C1 and D1 was the companies employing 5~49 workers. Types of industries which have a large number of companies exceeding noise exposure limit were automobile and trailer manufacturing, metal processing industry and primary metal manufacturing. A large number of work processes exceeding noise exposure limit were forming and processing work, cutting and bending work and grinding. To reduce the number of company exceeding noise exposure limit, the reduction counterplan should be focused on the type of industry and the work process which exceeded noise exposure limit frequently. However, the reduction counterplan is preemptively necessary to the type of industry and the work process which exceeded noise exposure limit consecutively if the purpose of reduction counterplan is not to merely reduce the number of company exceeding noise exposure limit but to abate workers' suffering from noise.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.3-3
• /
• 2000

Limit cycle analysis of attitude control system using gas jet thrusters is performed. Schmitt-Trigger and PD control laws are applied and solenoid valve time delay is considered. Phase plane method is used for calculation of characteristics of limit cycle. Important characteristics of resultant limit cycle such as frequency, amplitude, maximum rate, and duty ratio could be expressed analytically by proposed method.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.12 no.3
• /
• pp.2013-2018
• /
• 1970

Abrasion rate of coarse aggregates is an important factor to determine aggregates quality. Allowable limit of abrasion rate of coarse aggregates for concrete is 40% according to K.S. Strength and durability test of concrete with 19 efferent aggregates were made. From this test, it was found that allowable limit of abrasion rate of aggregates can be increased to 43%.

• Journal of the Korean Society of Safety
• /
• v.16 no.4
• /
• pp.109-114
• /
• 2001

Explosive characteristics of the city gas were determined by using the gas explosion apparatues. The explosive range is determined between lower explosive limit of 5.0% and upper explosive limit of 15.3% at atmosphere and even though the oxygen concentration is decreased, lower explosive limit is not changed, but upper explosive limit is rapidly decreased. The minimum oxygen for combustion is determined 10%. The maximum explosion pressure is determined 5.72$\textrm{cm}^2$ and the maximum rate of explosion pressure rise is oxygen concentration of 12% to determined 160.12$\textrm{cm}^2{\cdot}$sec.

• Korean Journal of Mathematics
• /
• v.7 no.2
• /
• pp.301-313
• /
• 1999

In this paper we obtain similar limit theorems of the Generalized Curie - Weiss model for a new class Hamiltonian. We expressed the saddlepoint approximation by large deviation rate and then obtain the limit theorems.

• Fire Science and Engineering
• /
• v.29 no.6
• /
• pp.20-25
• /
• 2015

In order to examine the explosion risk of 2-ethylhexanoic acid, we experimentally studied the explosion limit, explosion pressure, and rate of increase of the explosion pressure at different oxygen concentrations. The lower explosion limit was 3.2% at a temperature of $100^{\circ}C$, and the oxygen concentration was 40 to 70%. The upper explosion limit was 4.5% and the lower explosion limit was 4.0% at an oxygen concentration of 21%.The maximum explosion pressure of 2-ethylhexanoic acid was 1.4161 MPa at an oxygen concentration of 70%, and the rate of increase of the explosion pressure was 62.692 MPa/s at this concentration.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.29 no.1
• /
• pp.21-26
• /
• 2019

Objective: The aim of this study is to analyze an excess trend for domestic permissible exposure limit of trichloroethylene based on previous literature review. Materials and Methods: The research object is a trichloroethylene among 13 chemical substances regulated with PEL(Permissible Exposure Limit) in Occupational Safety and Health Act. The information utilized from this study is the work environment measurement data from 2004 to 2013. The highest level among concentration data measured at various workplaces was selected as a representative value through data process. N.D. (Not Detected) data was considered as 1/2 of LOD(Limit Of Detection). Results: Among work environment measurement data between 2004 and 2013, the highest number of excess workplace and excess rate(24 sites & 1.15%) was observed in 2008's data when applying the PEL(50 ppm) of trichloroethylene. When they are compared with the ACGIH's TLV-TWA(10 ppm), 2008's data showed the highest number of excess workplace and excess rate(175 sites & 8.37%). The number of excess workplace and excess rate related to PEL of trichloroethylene showed increase trend in 2005 but tended to decrease after 2008. Conclusions: Based on the results obtained from this study, the exposure level of trichloroethylene in case of domestic workers is not considered as a safe phase regardless of the year of work environment measurement year. Thus, a strictly preventive management in workplace should be provided for reducing exposure level of trichloroethylene.