• 소성∙가공
• /
• 제16권7호
• /
• pp.538-548
• /
• 2007

In this paper, a novel approach which enables rapid die surface modification for sheet metal forming process is proposed. In this method an implicit surface which interpolates a given set of control points and displacement constraints is generated to compute the displacements at arbitrary points located on die surface. The proposed method does not depend on the underlying surface representation type and is affected neither by its complexity nor by its quality. In addition, the domain decomposition method is introduced in order to treat large surface model. The global domain of interest is divided into smaller domains where the problem can be solved locally. And then the local solutions are combined together to obtain a global solution. In order to verify the validity and effectiveness of the proposed method, various surface modifications are carried out fur three kinds of die surface model including polygonal surface composed of triangular and rectangular meshes, polynomial surface and NURBS surface.

• Journal of Positioning, Navigation, and Timing
• /
• 제8권4호
• /
• pp.225-232
• /
• 2019

The satellite-based ionospheric model consists of local first-order plane function parameters for individual satellites and provides excellent accuracy in the flat ionospheric environment of the Korean Peninsula. This paper analyzes the performance of such model under the rapid changes in the ionosphere. Rapid changes in the ionosphere were observed in Korea from September to October 2014, and a satellite-based ionosphere model was applied to Wide Area Differential GPS (WADGPS) to analyze the navigation performance and the performance of estimating ionospheric delay errors. After processing the test data, it was confirmed that there was a deterioration in navigation performance and extrapolation performance in low-latitude areas and analyzed the cause.

• 대한전자공학회논문지
• /
• 제27권5호
• /
• pp.729-736
• /
• 1990

Oxide (RTO), nitrided-oxide(NO), and reoxidized-nitrided-oxide(ONO) films were formed by sequential rapid thermal processing. The film composition was investigated by Auger electron spectroscopy(AES). The Si/SiO2 interface and SiO2 surface are nitrided more preferentially than SiO2 bulk. When the NO is reoxidized, [N](atomic concentration of N) in the NO film decreased` especially, the decrease of [N] at the surface is considerable. The weaker the nitridation condition is, the larger the increase of thickness is as the reoxidation proceeds. The elelctrical characteristics of RTO, NO, and ONO films were evaluated by 1-V, high frequency (1 MHz) C-V, and high frequency C-V after constant current stress. The ONO film-which has 8 nm thick initial oxide, nitrided in NH3 at 950\ulcorner for 60 s, reoxidized in O2 at 1100\ulcorner for 60 s-shows good electrical characteristics such as higher electrical breakdown voltage and less variation of flat band voltage under high electric field than RTO, and NO films.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.759-762
• /
• 2000

Rapid Prototyping (RP) techniques have their unique characteristics according to the working principles: stair-stepped surface of parts due to layer-by-layer stacking, low build speed caused by line-by-line solidification to build one layer, and additional post processing to improve surface roughness, so it is required very high cost to introduce and to maintain RP apparatus. The objective of this study is to develop and design a new RP process, Variable Lamination Manufacturing using expandable polystyrene foam sheet as part material (VLM-S), which can make up for the disadvantage of existing techniques, and to develop an apparatus to implement the process. In order to examine the possibility of practical utilization of the proposed VLM-S process for prototyping of a general three-dimensional shape, an auto-shift lever knob and a pyramid shape were fabricated.

• 한국재료학회지
• /
• 제13권5호
• /
• pp.285-291
• /
• 2003

The nanosized silver and gold particles are prepared by ERC method in which metal vapors with high temperature is rapidly quenched by coolants such as liquid nitrogen or liquid argon. In order to monitor the crystal structural changes on the internal and the surface of the nanosized noble metal particles, lattice parameter, internal strain and Debye-Waller factor are investigated, and the calculation of X-ray diffraction scattering intensity is performed. The lattice parameters of silver and gold particles agree with those of bulk materials, and crystal internal strain of the metal particles is not changed by rapid cooling. The Debye-Waller factor of gold particles is increased with decreasing particle size because of the surface softening phenomenon of nanosized particles, but the crystal structural change on the surface of the particles is not detected from the comparison the calculated X-ray diffraction profile with the experimental profile on gold particles with the particle size of 4 nm.

• 소성∙가공
• /
• 제23권8호
• /
• pp.475-481
• /
• 2014

Water quenching is one method of cooling after hot forming, which is presently being used for the manufacturing of automobile parts. The formed parts at room temperature are heated and then cooled rapidly in a water bath to produce high strength. The formed parts may undergo excessive thermal distortion during the water quench. In order to predict the distortion during water quenching, a coupled thermo-mechanical simulation is needed. In the current study, the simulation of heating and cooling of boron steel cylinders was performed. The material properties for the simulation were calculated from JMatPro, and the convective heat transfer coefficient was obtained from experimental tests. The results show that the thermal distortion and the residual stresses are well predicted by the coupled simulation.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 추계학술대회 논문집
• /
• pp.763-766
• /
• 2000

Rapid Prototyping(RP) techniques have their unique characteristics according to the working principles: stair-stepped surface of parts due to layer-by-layer stackin, low build speed caused by line-by-line solidification to build one layer, and additional post processing to improve surface roughness, so it is required very high cost to introduce and to maintain RP apparatus. The objective of this study is to develop software for automatic generation of unit shape part (USP) for a new RP process, Variable Lamination Manufacturing using linear hotwire cutting technique and expandable polystyrene foam sheet as part material (VLM-S). In order to examine the applicability of the developed software to VLM-S, USP's of general three-dimensional shapes, such as an auto-shift lever knob and a pyramid shape were generated.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.137-140
• /
• 1997

In general, stereolithography parts is not suitable for master pattern. Because of its bad surface roughness. Therefore, To reduce roughness it requires post-process that is depending on user skill and takes long time to do. This study aims to develop an expert system which can select an optimal build orientation, reduce roughness and shorten post-processing time. Genetic Algorithm was introduced for optimization. A simplified computation model was developed for real-time response. For accurate roughness estimation, mterpolation of experimental data was implemented.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.553-556
• /
• 2003

End-milling have been used in the industrial world because it is very effective to the manufacture of mechanical parts with various shape. Recently the end-milling processing is needed the high-precise technique with good surface roughness and rapid time in aircraft, automobile part and molding industry. Therefore this study carried to decide the optimum cutting condition for surface roughness and rapid manufacturing time using design of experiment and ANOVA. From the results of experimentation, surface roughness have an effect on cutting direction, spindle speed and depth of cut. And then the optimum condition used Taguchi design is upward cutting in cutting direction, 600rpm in spindle speed, 240mm/min feed rate, 2mm in axial depth of cut and 0.25mm radial depth of cut. By using design of experiment, it is effectively represented shape characteristics of working surface in end-milling.

• 정보처리학회논문지A
• /
• 제8A권2호
• /
• pp.75-80
• /
• 2001

The rapid design of the embedded system is crucial for improving the product’s competitiveness. Existing statechart tools used for designing the embedded system rely on the copy and paste of the statechart for reuse. However, such method has a major drawback of wasting both time and cost of the system developer. This paper implements the component supporting tool. A tool that makes efficient reuse of a statechart by adding a component function to the existing functions is implemented in this paper. Also, to add a component function, this paper restructured the contract as protocol of the inter-component. The implemented tool helps not only reduce the life cycle of a product, but also enhance a product’s competitiveness by supporting the product’s time-to-market.