• Transactions of Materials Processing
• /
• v.7 no.5
• /
• pp.450-458
• /
• 1998

The high temperature deformation behavior of Al 5083 alloy has been studied in the temperature range of 350 to 520 ${\circ}C$ and strain rate range of 0.2 to 3.0/sec by torsion test. The strain rate sensitivity(m) of the material was evaluated and used for estabilishing power dissipation maps following the dynamic material model. These maps show the variation of efficiency of power dissipation(${\eta}$=2m/(2m+1)) with temperature and strain rate. Hot restoration of dynamic recrystallization (DRX) was analyzed from the flow curve, deformed microstructure, and processing maps during hot deformation. Also, the effect of deformation strain on the efficiency of power dissipation of the alloy was analysed using the processing maps. Moreover relationship between the hot-ductility and efficiency of power dissipation of the alloy depending on thmperature and strain rate was studied using the Zener-Hollomon parameter(Z=${\varepsilon}$exp(Q/RT) It is found that the maximum efficiency of power dissipation for DRX in Al 5083 alloy is about 74.6 pct at the strain of 0.2. The strain rate and temperature at which the efficiency peak occurred in the DRX domain is found to be ∼0.1/sec and ∼450${\circ}C$ respectively.

• The KSFM Journal of Fluid Machinery
• /
• v.4 no.1 s.10
• /
• pp.30-37
• /
• 2001

The experimental study on the effect of axial clearance between the tip of impeller blades and stationary shroud has been performed. The investigated compressor, which is a part of a small auxiliary power unit engine, consists of a curved inlet, a centrifugal impeller, a channel diffuser and a plenum chamber. It was designed for a total pressure ratio of 4.3 and an efficiency of $77\%$ at design speed of 60,000 rpm. The experiments are carried out in an open-loop centrifugal compressor test rig driven by a turbine. For the four different clearance ratios Cr(clearance/impeller tip width) of 6.25, 10.93, 15.60 and 20.30 percent, the overall performance data are obtained at $97\%,\;90\%$ and $80\%$ of the design speed. The results show the overall pressure ratio decrease of $7.7\%$ and the efficiency loss of $8.7\%$ across the variation of clearance ratio near the design speed. It also indicates that the influence of tip clearance became weaker as the flow rate is reduced and the stable operating range is not significantly influenced by the change of clearance ratio.

• Korean Journal of Materials Research
• /
• v.14 no.7
• /
• pp.489-493
• /
• 2004

The electrical property of MMC is essentially important to some applications such as power transmission lines and cables, electronic and electrical components as well as electromagnetic shielding equipments. The behavior of electrical resistivity of $SiC_{w}/Al$ alloy composites under as-extruded and annealed conditions has been investigated within the temperature range from room temperature to $450^{\circ}C$. It can be seen that within entire temperature range, the electrical resistivity of composites was higher than that of an unreinforced matrix alloy under the same condition of either as-extrusion or annealing. The temperature dependence of both exhibited positive incline like a typical metal. The variation of electrical resistivity of an unreinforced matrix alloy with temperature from ambient temperature to $450^{\circ}C$ was nearly monotonous, while those of composites increased monotonously at low temperature and rose to a high level after about $250^{\circ}C or 275^{\circ}C$. The difference of these temperature dependences on electrical resistivity can be interpreted as qualitatively the interfaces of $SiC_{w}$ fibers and matrix, where act as nucleation sites.

• Journal of Ecology and Environment
• /
• v.33 no.3
• /
• pp.187-193
• /
• 2010

Seed germination is a biological process that is affected by a variety of genetic and environmental factors. The cardinal temperature and thermal time are required for germination. The principal objective of this study was to identify and characterize variations in the base, optimum, and maximum germination temperatures of Haloxylon aphyllum L. from two seed sources, in order to establish models for use in predicting seeding dates. Mature H. aphyllum seeds were germinated at temperatures between 5 and $35^{\circ}C$. The germination behavior of H. aphyllum seeds to different temperature regimens in light was evaluated over a temperature range of $5-35^{\circ}C$ at intervals of $5^{\circ}C$. The rate of germination increased between base and optimum thermal conditions, and decreased between optimum and maximum thermal conditions; the germination rate varied in a linear fashion at both sub-optimal and supra-optimal temperatures. The linear regression fit the range of germination rates at $5^{\circ}C$ to $25^{\circ}C$ and $25^{\circ}C$ to $30^{\circ}C$, and thus the base temperature, optimum temperature, and maximum temperature for the germination of H. aphyllum were measured to be $0.6^{\circ}C$, $25.69^{\circ}C$, $37.90^{\circ}C$, and $1.76^{\circ}C$, $21.56^{\circ}C$, $37.90^{\circ}C$ for Qom and the Fars dune desert respectively.

• Computers and Concrete
• /
• v.3 no.6
• /
• pp.389-400
• /
• 2006

This paper presents the investigations towards developing a better understanding on the contribution of steel fibers on the tensile strength of high-performance fiber reinforced concrete (HPFRC). An extensive experimentation was carried out with w/cm ratios ranging from 0.25 to 0.40 and fiber content ranging from zero to 1.5 percent with an aspect ratio of 80. For 32 concrete mixes, flexural and splitting tensile strengths were determined at 28 days. The influence of fiber content in terms of fiber reinforcing index on the flexural and splitting tensile strengths of HPFRC is presented. Based on the test results, mathematical models were developed using statistical methods to predict 28-day flexural and splitting tensile strengths of HPFRC for a wide range of w/cm ratios. The expressions, being developed with strength ratios and not with absolute values of strengths and are applicable to wide range of w/cm ratio and different sizes/shapes of specimens. Relationship between flexural and splitting tensile strengths has been developed using regression analysis and absolute variation of strength values obtained was within 3.85 percent. To examine the validity of the proposed model, the experimental results of previous researchers were compared with the values predicted by the model.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.44 no.4
• /
• pp.62-74
• /
• 2002

The purpose of this study is to find the variation of sedimentation patterns before Saemangeum reclamation. Residual flow before Saemangeum reclamation was calculated diagnostically from the observed water temperature and salinity data in May 1992 by the Marine Development Institute of Kunsan National University and wind data which were obtained from spring 1969 through winter 1977 by the Gunsan Meteorological Observatory. Three dimensional movements of injected particles due to currents, turbulence and sinking velocity are tracked by the Euler-Lagrange method. Calculated sedimentation patterns of riverine materials are highly similar to the observed ones. When suspended sediments with the size of soil grain of 60 ${\mu}m$ are injected from the Mangyeong River, their dispersion range of sediment is about 25km for 24 hours after the injection, while about 35km for 72 hours after the injection. When suspended sediments with the size of soil grain of 200 ${\mu}m$ are injected, their dispersion range of sediment is about 18km for 24 hours after the injection, while about 21km for 72 hours after the injection.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.4
• /
• pp.125-134
• /
• 2003

In this study, Mooney-Rivlin 1st model and Mooney-Rivlin 3rd model are adopted as strain energy density functions of the rubber compounds of a radial tire. It is shown that the FE analysis using Mooney-Rivlin models for rubber compounds may provide good approximations by employing the appropriate strain range of experimental stress-strain data in a way to describe the stress-strain relationship accurately. Especially, Mooney-Rivlin 3rd model gives an accurate stress-strain relationship regardless of the fitting strain range used within the strain of 100%. The static nonlinear FE analysis of a tire inflation is performed by employing an axisymmetric model, which shows that the outside shapes of the tire before and after inflating the tire agree well with those of the real tire. Additionally, the deformations at crown center and turning point on sidewall, distribution of belt cord force, interlaminar shear strain are predicted in terms of variation of belt cord angle which is known as the most influential factor in inflation behavior of a tire.

• Speech Sciences
• /
• v.9 no.3
• /
• pp.3-16
• /
• 2002

We examined some problems in speaker identification procedures: transformation of acoustic parameters into auditory scales, invalid measurement values, and comparability of spectral energy values across the frequency range. To resolve those problems, we analyzed the acoustic spectral energy of three Korean numbers produced by ten female students from narrow-band spectrograms at 19 proportional time points of each voiced segment. Then, cells of the first five spectral matrices were averaged to form a matrix model for each speaker. The correlation coefficients and sum of the absolute amplitude difference in each pair of the spectral models of the ten subjects were obtained. Also, some individual matrix models were compared to those of the same subject or the other subject with a similar spectral model. Results showed that in numbers '2' and '9' subjects could not be clearly distinguished from the others but in number '4' it shed some possibility of setting threshold values for speaker identification if we employed the coefficients and the sum of absolute difference. Further studies would be desirable on various combinations of the range of long-term average spectra and the degree of signal pre-emphasis.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.3
• /
• pp.395-399
• /
• 2002

The voltammetric behavior of spontaneously adsorbing Mo layers on Pt(111) and Pt(100) electrodes has been studied to estimate the number of electrons involved in the electrochemical processes of spontaneously adsorbed Mo and the number of the bloc ked Pt sites for hydrogen adsorption. On Pt(111) and Pt(100) surfaces, the spontaneously adsorbed Mo layers showed redox peaks at 0.10 V and 0.15 V, respectively, and continuous current-potential waves in the conventional hydrogen region. Since the potential range of the Mo redox processes on both surfaces overlapped partially with the potential range of hydrogen adsorption, the variation in the ratio of the total charge of Mo and H ($Q_H$ +$Q_{MO}$) to the hydrogen charge of clean Pt electrode ($Q_H^0$) was analyzed. From the analysis, six electrons were estimated to be involved in the electrochemical processes of the spontaneously adsorbed Mo, and four Pt sites for hydrogen adsorption were calculated to be blocked by one adsorbed Mo atom. Based on these figures and the pH dependence of the Mo redox processes, we have proposed an electrochemical equation for the spontaneously adsorbed Mo. This electrochemical equation led us to conclude that the saturation coverage of the spontaneously adsorbed Mo is 0.25. The coverage of Mo less than 0.25, however, could not be determined voltammetrically due to the convolution of the charges of Mo and H.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.22 no.11
• /
• pp.788-797
• /
• 2010

This study examines the influence of fluctuating daylight illuminance on daylight dimming control systems. Field measurements were performed for a full-scale mocked-up model under various daylight conditions in winter. Fluctuating ranges for a partially-shielded photosensor were great when the variation of sky ratio was great. When solar altitude was lower the illuminance and fluctuating range of illuminance were great due to the influence of direct components of daylight and the interrefelction between surfaces in rear area of space. It implies that daylight dimming system would not function effectively, unless the desktop illuminance by daylight is enough. Fluctuation ranges of photosensor illuminance were lower than 50 lx under clear sky conditions, but they were greater than 100 lx under partly-cloudy sky conditions. It means that the fluctuation range of electric light output of lighting fixture would greater under the partly-cloudy conditions and cause potential visual annoyance to occupants. Outdoor vertical illuminance reaching the windows would be an effective factor that can be used to predict the fluctuation of photosensor signals for effective controls of daylight dimming system.