• Journal of Bio-Environment Control
• /
• v.17 no.4
• /
• pp.252-260
• /
• 2008

This study was conducted to observe the characteristics of mineral nutrient uptake of single-node cutting rose 'Versilla' and to determine optimal nutrient solution control method for soilless culture of 'Versilla' in a closed hydroponic system. Nutrient solution was managed by five different control methods: macro- and micro-element control in aeroponic system (M&M), macroelement control in aeroponic system (M), nutrient solution supplement in aeroponic system (S); electrical conductivity (EC) control in aeroponic system(EC-A); EC control in deep flow technique system(EC-D). The concentration of $NO_3$-N exceeds optimal range whereas P and Mg decreased at the later stage of plant growth with the EC control method, EC-A and EC-D. The overall mineral nutrient content increased with S. On the other hand the nutrient content at the root environment was maintained optimal with M&M and M. The nutrient solution control methods had significantly effect on the cut-flower quality. In the M&M and M, flower length, fresh weight and root activity were higher than those with the other mineral nutrients control methods. The maximal efficiency of photochemistry (Fv/Fm) was higher for M&M, M and S than that with EC-A and EC-D. Based on the above results, it is highly recommended to control nutrient solution by mineral nutrient control methods (M&M and M) in a closed hydroponic system for single-node cutting rose, 'Versillia'.

• Journal of the Korean Society for Precision Engineering
• /
• v.3 no.2
• /
• pp.62-75
• /
• 1986

An experimental investigation of the machining characteristics such as cutt- ing resistance, surface roughness and tool wear in turning the test pieces of SM45C steel with both coated and uncoated carbide tool tips under various cutting conditions was conducted. Also a specially designed simple vibration damping device was experimentally evaluated for its effectiveness on machined surface roughness and a vibration test was conducted to confirm its ability to reduce the amplitude. Based on these tests finding, the following conclusions are made; 1. The cutting resistance($\textrm{p}_{1}$) increases as the depth of cut(d) increases at fixed feed rate(f) over the cutting speed(v) range of 43-226 m/min and p decreses about 18% average when V is increased for fixed d and f. At V= 226m/min, $\textrm{p}_{1}$/for A, C tips are about the same level but $\textrm{p}_{1}$ for B tip is 15% less than A, C tips. 2. The specific cutting resistance(Ks) at V=226 m/min was derived for A, B, C tips respectively and the value of Ks for B rip is about 20% less than A, C tips. 3. The surface roughness(Ra) improves significantly as the cutting speed(V) is increased and this effect was greater when V>100 m/min. On the other hand, Ra deteriorates as the feed rate(f) is increased and this trend was accelerated when f>0.3 mm/rev. With regard to the difference of Ra values among A, B, C tips, at V=226m/min, d=0.4mm, and f=0.31-0.61mm/rev, Ra values for B.C tips are about 17% less than tip A. 4. The experimental tool wear equations were derived for A, B, C tips and from these equations, the tool life($\textrm{T}_{\textrm{L}}$) baced on the I.S.O. criteria was calculated to be $\textrm{T}_{\textrm{L}}$<$\textrm{T}_{\textrm{LB}}$<$\textrm{T}_{\textrm{LC}}$ for both flank wear($\textrm{V}_{\textrm{B}}$) and boundary wear($\textrm{V}_{\textrm{N}}$). Hence, the coated tips are superior to the uncoated tip and tip C is considered to be the best. 5. The cutting resistance may be slightly reduced and the surface rounghness improved when the damper is used especially when V>100 m/min. Therefore this damping device is considered to be effective and practical. The experimental surface roughness equations were also derived. Based on the vibration test, it is established that the surface roughness improvement was the result of amplitude reduction made possible by the damper.

• Journal of Korean Society of Forest Science
• /
• v.109 no.4
• /
• pp.468-476
• /
• 2020

we developed a stand density management diagram for Quercus variabilis in order to predict the final cutting ages of coppice forests based on management objectives. The sample data were classified into two groups: 603 data points for analysis and 113 data points for verification. Using these data, a stand density management diagram was constructed and a goodness-of-fit test was performed. The explanatory power (R2) of the constituent models for the stand density management diagram was 0.732 for the equivalent height curve and 0.990 for the equivalent diameter curve. According to the analysis of the final cutting age rangeof the highest production, the final cutting ages for 900 buds remaining per hectare was 42-44 years, and that for the 1,800 buds remaining per hectare was 38-42 years. With the third-grade log set as the production target, the final cutting age range with site index 16 and 14 was 25-28 years and 29-33 years, respectively. The results of this study provide baseline data for establishing a management plan for Q. variabilis coppice stands.

• Journal of the Korean Ceramic Society
• /
• v.27 no.1
• /
• pp.102-108
• /
• 1990

WC-Co composites are widely used as cutting or drilling tools because of their high hardness, strength, and fracture toughness. The working temperature is, however, generally in the range of 300-$700^{\circ}C$ so thermal shock fracture of WC-Co can occur. In this study, the strength, fracture toughness and fracture surface of 16wt% Co bonded tungsten carbide composites before and after thermal shock were observed.

• Economic and Environmental Geology
• /
• v.13 no.2
• /
• pp.80-90
• /
• 1980

A geologic disasters in Ulreung-island is forming along the slope of pyroclastic, deposits and this paper discusses soil mechanics and properties and morphologies of pyroclastic soil. The typers of degradation are determined by cutting the soil and classified genetically. Finally, the range of stability is deduced from dip of slope (${\alpha}$) and lengh of slope (l) as the following;.

• Horticultural Science & Technology
• /
• v.30 no.4
• /
• pp.449-462
• /
• 2012

The objectives of this study were to measure the range of motion for joints and muscle activation of upper limb for flower arrangement tasks for physical rehabilitation and to test horticultural therapy programs using flower arrangement tasks for improving upper limb function of the patients with stroke. Major flower arrangement tasks were classified with eight tasks (cutting 1, thick stem; cutting 2, thin stem; fixing 1, long stem; fixing 2, short stem; rolling a leaf; bending 1, thick stem; bending 2, thin stem; and winding, using a wire) based on the occupational analysis. When eight male university students (mean age $24.1{\pm}2.5$ years) conducted the eight flower arrangement tasks, range of motion for joints and muscle activation of upper limb were measured by a 3D motion analyzer and electromyography, respectively. Based on the results of the range of motion and muscle activation of upper limb, horticultural therapy programs using flower arrangement tasks (total 33 sessions) for improving upper limb function of the patients with stroke was conducted at a rehabilitation hospital, Seoul, South Korea and then the range of motion, grip strength, and upper limb function of the patients were tested. Among the eight flower arrangement tasks, cutting 1, winding, and bending 1 induced the highest value for the range of motion in joints of shoulder, elbow, and wrist, respectively (P < 0.001). In terms of muscle activation, eight flower arrangement tasks performed in this study showed various patterns of muscle activation and several muscles were simultaneously used for each task (P < 0.001). In addition, thickness and length of the materials used in a task had a prominent effect on the range of motion for joints and muscle activation of upper limb (P < 0.001). The stroke patients had positive effects for their range of motion of upper limb (shoulder, forearm, and elbow), grip strength, and overall upper limb function through the horticultural therapy program. Thus, this study suggested that flower arrangement tasks would be a potential horticultural activity for physical rehabilitation program. It would be interesting to apply a customized horticultural therapy program using flower arrangement tasks according to the symptoms of patient for physical rehabilitation.

• Design & Manufacturing
• /
• v.11 no.2
• /
• pp.46-50
• /
• 2017

EPS used in lost foam casting elastic modulus is extremely low. So it is necessary to derive machining conditions for effective cutting. Therefore this study were analyzed end-milling machining conditions to affecting the surface roughness of EPS foam. The machining conditions were set to depth, feed, and RPM at 3-level. And 18experimental conditions were derived using mixed orthogonal array. The most important condition for surface roughness is RPM. In addition, RPM machining condition range test that can realize surface roughness less than $10{\mu}m$ was performed. he range of RPM conditions is more than 15,000. However the range of RPM conditions is a condition that is difficult to use in actual field. In the future variance analysis and experiments are needed to derive the range of machining conditions available.

• Journal of the Korean institute of surface engineering
• /
• v.15 no.3
• /
• pp.138-145
• /
• 1982

The effects of the simultaneous variations of the ratio of feed gases(H2/N2 Flow ratio), feed gas flow rate (H2/N2, total-flow rate) and partial pressures of TiCl4 (PTiCl41) as well as deposition time and cobalt content of the substrate on the deposition rate of the TiN Coated Cemented Tungsten Carbide Tools were investigated. Deposition was carried out in the temperature range of 930$^{\circ}C$-1080$^{\circ}C$ and an activation energy of 46.5 Kcal/mole can be calculated. Transverse rupture strength was noticeably reduced by the TiN coating on the virgin surfa-ce of Cemented Tungsten Carbide, the extent of which was decreased according to the coa-ting thickness. Microhardness value observed on the work was in the range of 1700∼2000kg/mm, which were in well agreement with the value of bult TiN. The wear resistance of TiN layers was performed by turning test and it was observed that crater and flank resistance remarkably enhanced by TiN coating.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.7C
• /
• pp.723-727
• /
• 2002

In this paper a new remote control system for operating indoor gas(LPG) range safely based on PLM(Power Line Modem) and telephone is developed because it would make disasters of properties and lives by user's carelessness or worker's bad installation, etc. The system includes the following elements: a telephone line interface system for user to call from the outdoors to the indoors, a communication system using the power line as a communication media, a system of cutting off gas and a alarm system.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.29 no.7 s.144
• /
• pp.978-986
• /
• 2005

The color of apparel products have a close relationship with the face skin colors of consumers. In order to extract the favorable colors which flatter to consumer's face skin colors, this study was carried our to classify the face skin colors of Korean females. The criteria that select new subjects who have the classified face skin colors have to be decided. With color spectrometer, JX-777, face skin colors of subjects were measured and classified into three clusters that had similar hue, value and chroma with Munsell Color System. Sample size was 324 Korean females and other new 10 college girls. Data were analyzed by K-means cluster analysis, ANOVA, Duncan multiple range test, Stepwise discriminant analysis using SPSS Win. 12. Findings were as follows: 1. 324 subjects who have YR colors were clustered into 3 face skin color groups. 2. Discriminant variables of face skin colors were 5 variables : b value of cheek, V value of forehead, L value of cheek, C value of forehead and H value of cheek by the standardized canonical discriminant function coefficient 1. 3. Hit ratio of type 1 was $96.8\%$, of type 2 was $94.9\%$, of type 3 was $100.0\%$ and mean of hit ratio was $96.9\%$ by canonical discriminant function of 5 variables. 4. With the unstandardized canonical discriminant function coefficient and constant, canonical discriminant function equation 1 and 2 were calculated. And cutting score and range of score of the classified types were computed. The criteria that select the new subjects were decided.