• 한국분무공학회지
• /
• 제22권4호
• /
• pp.190-196
• /
• 2017

The aim of this work is to investigate the combustion and exhaust emission characteristics of low-temperature combustion (LTC) at various EGR test conditions using a single cylinder common-rail diesel engine. In high EGR rate combustion mode with DME fuel, 30% (${\Phi}=0.61$) and 50% (${\Phi}=0.86$) of EGR were respectively examined, and then the combustion, exhaust emissions, nano-particle characteristics of each cases were measured. From these results, it revealed that The ignition delay and combustion duration are prolonged as the increase of EGR rate. In addition, at an advanced injection timing (BTDC $30^{\circ}$), ignition delays were fairly increased because the dilution effect of EGR and also low charge in-cylinder temperature created a lean mixture, thus decreased the peak release rate.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 C
• /
• pp.1487-1489
• /
• 2003

For this research, we developed the hardware and software of the measurement system for on-line test and evaluation. The software controls the hardware of the mesurement data and acts as interface between users and the system hardware. In this paper, practical experiment is performed to verify temperature characteristics of induction motor for high speed rail. The experimental test carried out new temperature measurement method. Through this test, temperature characteristics of induction motor is verified.

• 대한기계학회논문집B
• /
• 제36권12호
• /
• pp.1151-1159
• /
• 2012

본 논문에서는 노즐홀 직경을 확대하여 유량을 증가시킨 DME 인젝터의 가시화 실험과 분무 해석을 수행하였다. 해석의 신뢰성을 확보하기 위하여 가시화 실험과 분무해석을 비교하였고, 실엔진 모사 조건에서 분무 해석을 수행하여 DME의 거동을 예측하였다. 분사 압력과 분위기 압력이 각각 35MPa 및 5MPa인 경우 가시화 실험과 분무 해석의 도달거리는 3.57%의 차이를 나타내었다. 실엔진 모사 해석의 경우, 완전하게 발달된 DME의 분무 도달거리는 분위기 온도와 압력의 비가 300K/MPa에서 42mm로 최대를 나타내었고, 300K/MPa미만의 영역에서 DME의 분무는 분위기 압력, 300K/MPa초과의 영역에서는 분위기 온도의 영향이 지배적임을 확인하였다.

• 한국자동차공학회논문집
• /
• 제19권4호
• /
• pp.72-77
• /
• 2011

This study is to investigate the effect of the distillation temperature in ultra low sulfur diesel fuel on exhaust emissions in the low-temperature diesel combustion with 1.9L common rail direct injection diesel engine. Low temperature diesel combustion was achieved by adopting an external high EGR rate with a strategic injection control. The engine was operated at 1500 rpm 2.6 bar BMEP. The 90% distillation recovery temperature (T90) was $270^{\circ}C$ and $340^{\circ}C$ for the respective cetane number (CN) 30 and 55. It was found that there exists no distinctive discrepancy on exhaust emissions with regards to the different T90s. The high CN (CN55) fuels follow the similar trend of exhaust emissions as observed in CN30 fuels' except that high T90 fuel (CN55-T340) produced higher PM compared to low T90 fuel (CN55-T270). This may come from that high T90 plays an active role in aggravating the degree of fuel-air mixture preparedness before ignition.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.2487-2492
• /
• 2011

At high rail temperature above the neutral temperature, high compressive axial stresses will occur in the rails. High thermal axial force and vehicle loads cause the track to shift in a lateral direction and the formation of track geometry imperfections (track irregularity). When the thermal stress level and track irregularity with vehicle load reach a critical value, the track loses stability. In many studies, the stability of CWR tracks is analyzed. However these studies are only considered in temperature load. The main objective of this investigation was to estimate a new, comprehensive, realistic, the stability of CWR tracks considering wheel load. The ballast resistance is changed by wheel load. When the wheel load is applied, rails and ties are moved upward or downward. In this case the friction between ties and ballasts is decreased or increased. In this study the change of the ballast resistance of each tie was applied to the nonlinear analysis of CWR tracks.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 A
• /
• pp.378-380
• /
• 1998

In this paper, to analyse the temperature rise of the traction motor the methods evaluating the heat sources and heat transfer coefficients are represented. And the results of temperature analysis of the 3- designed cases of traction motor also are represented. In case of KERI01, the tempeature rise of the rotor is higher than DW01 and DW02. In the stators, case of DW01 is presented higher temperature rise than DW02 and KERI01.

• 한국전산구조공학회논문집
• /
• 제29권2호
• /
• pp.169-177
• /
• 2016

슬라이딩 궤도는 콘크리트 궤도와 교량 바닥판 사이에 저마찰 슬라이드층을 두어 레일신축이음장치와 같은 특수 장치를 적용하지 않고도 궤도-교량 상호작용 효과를 효과적으로 저감시킬 수 있는 새로운 궤도 시스템으로 개발되고 있다. 이 논문에서는 장경간 교량에 슬라이딩 궤도와 레일신축이음장치를 각각 적용한 경우에 대하여 궤도-교량 상호작용해석을 수행하고 그 결과를 비교 검토하였다. 대상교량은 상호작용 효과를 극대화하기 위하여 9경간 연속 PSC교와 2경간 연속 강합성교를 포함하며, 총 연장 1,205m, 최대 고정지점간 거리 825m인 장경간 교량을 선정하였다. 해석결과 슬라이딩 궤도는 레일신축이음장치를 적용한 경우보다 레일 부가 축력이 더 작은 것은 물론, 지점부에 재하되는 수평 반력 또한 작게 나타나 궤도-교량 상호작용 저감 효과가 뛰어난 것으로 확인되었다. 반면 슬라이딩 궤도는 온도하중에 의해 높은 슬래브 축력이 발생되므로, 궤도 설계 시 슬래브 축력에 대한 단면 설계에 주의를 기울일 필요가 있다.

• 한국자동차공학회논문집
• /
• 제21권4호
• /
• pp.1-7
• /
• 2013

DME spray characteristics were investigated about varied ambient pressure and fuel injection pressure using the DME common rail fuel injection system when the nozzle holes diameter is varied. The common rail fuel injection system with DME cooling system was used since DME has properties of compressibility and vaporization in atmospheric temperature. The fuel injection quantity and spray characteristics were measured. The spray analysis parameters were spray shape, penetration length, and spray angle at six nozzle holes. Three types of injector were used, the nozzle holes diameter were 0.166 mm (Injector 1), 0.250 mm (Injector 2), and 0.250 mm with enlargement of orifice hole from 0.6 mm to 1.0 mm (Injector 3). The fuel injection pressure was varied by 5MPa from 35 to 70MPa when the ambient pressure was varied 0, 2.5, and 5MPa. When using Injector 3 in comparison to the others, the DME injection quantity was increased 1.69 ~ 2.02 times. Through this, it had the similar low heat value with diesel which was injected Injector 1. Among three types of injector, Injector 3 had the fastest development velocity of penetration length. In case of spray angle, Injector 2 had the largest spray angle. Through these results, only the way enlargement the nozzle holes diameter is not the solution of DME low heat value problem.

• 한국자동차공학회논문집
• /
• 제20권2호
• /
• pp.90-97
• /
• 2012

It is investigated of the DME spray characteristics about varied ambient pressure and fuel injection pressure using the common rail fuel injection system when the nozzle holes diameter is varied. The common rail fuel injection system and fuel cooling system is used since DME has compressibility and vaporization in atmospheric temperature. The fuel injection quantity and spray characteristics were measured. The spray was analyzed of spray shape, penetration length, and spray angle at the six nozzle holes. The 2 types injector were used, the one was 0.166 mm diameter the other one was 0.250 mm diameter. The ambient pressure which is based on gage pressure was 0 MPa, 2.5 MPa, and 5 MPa. The fuel injection pressure was varied by 5 MPa from 35 MPa to 70 MPa. When using the converted injector, compared to using the common injector, the DME injection quantity was increased 127 % but it didn't have the same heat release. Both of the common and converted injector had symmetric spray shapes. In case of converted injector, there were asymmetrical spray shapes until 1.2 ms, but after 1.2 ms the spray shape was symmetrical. Compared with the common and converted injector, the converted injector had shorter penetration length and wider spray angle than the common injector.

• 한국자동차공학회논문집
• /
• 제19권3호
• /
• pp.146-153
• /
• 2011

American NREL (National Renewable Energy Laboratory) reported that BDF20 could reduce PM, CO, SOx, and cancerogenic matters by 13.6%, 9.3%, 17.6%, and 13% respectively, compared to diesel fuel. BDF20 has been being tested on garbage trucks and official vehicles at Seoul City, which is positive on air environment, but negative on combustion by higher viscosity in winter season. This study investigated the combustion characteristics by applying pilot injection for improving the deterioration of combustibility caused by the higher viscosity of the BDF20 with the combustion flames taken by a high-speed camera and the cylinder pressure diagram. A 4-cycle single-cylinder diesel engine was remodeled to a visible 2-cycle engine taking the flame photographs, which has a common-rail injection system. The test was done laboratory temperature at $5{\sim}6^{\circ}C$. The results obtained are summarized as follows, (1) In the case of without pilot injection, the flame propagation speed was slowed and the maximum combustion pressure became lower. The phenomena became further aggravated as the fuel viscosity gets higher. (2) In the case of with pilot injection, early stage of combustion such as rapid ignition timing and flame propagation was activated since intermediate products formed by pilot injection act as a catalyst for combustion of main fuel.