• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.7
• /
• pp.115-121
• /
• 2013

We fabricated thin film transistors (TFTs) using TiInZnO(TiIZO) thin films as active channel layer. The thin films of TiIZO were deposited at room temperature by RF-magnetron co-sputtering system from InZnO(IZO) and Ti targets. We examined the effects of titanium addition by X-ray diffraction, X-ray photoelectron spectroscopy and the electrical characteristics of the TFTs. The TiIZO TFTs were investigated according to the radio-frequency power applied to the Ti target. We found that the transistor on-off currents were greatly influenced by the composition of titanium addition, which suppressed the formation of oxygen vacancies, because of the stronger oxidation tendency of Ti relative to that of Zn or In. A optimized TiIZO TFT with rf power 40W of Ti target showed good performance with an on/off current ratio greater than $10^5$, a field-effect mobility of 2.09 [$cm^2/V{\cdot}s$], a threshold voltage of 2.2 [V] and a subthreshold swing of 0.492 [V/dec.].

• The Journal of Advanced Prosthodontics
• /
• v.5 no.4
• /
• pp.402-408
• /
• 2013

PURPOSE. The aim of this study was to evaluate the surface properties and in vitro bioactivity to osteoblasts of magnesium and magnesium-hydroxyapatite coated titanium. MATERIALS AND METHODS. Themagnesium (Mg) and magnesium-hydroxyapatite (Mg-HA) coatings on titanium (Ti) substrates were prepared by radio frequency (RF) and direct current (DC) magnetron sputtering.The samples were divided into non-coated smooth Ti (Ti-S group), Mg coatinggroup (Ti-Mg group), and Mg-HA coating group (Ti-MgHA group).The surface properties were evaluated using scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The surface roughness was evaluated by atomic force microscopy (AFM). Cell adhesion, cell proliferation and alkaline phosphatase (ALP) activity were evaluated using MC3T3-E1 cells. Reverse transcription polymerase chain reaction (RT-PCR) analysis was performed. RESULTS. Cross-sectional SEM images showed that Mg and Mg-HA depositionson titanium substrates were performed successfully. The surface roughness appeared to be similaramong the three groups. Ti-MgHA and Ti-Mg group had improved cellular responses with regard to the proliferation, alkaline phosphatase (ALP) activity, and bone-associated markers, such as bone sialoprotein (BSP) and osteocalcin (OCN) mRNA compared to those of Ti-S group. However, the differences between Ti-Mg group and Ti-MgHA group were not significant, in spite of the tendency of higher proliferation, ALP activity and BSP expression in Ti-MgHA group. CONCLUSION. Mg and Mg-HAcoatings could stimulate the differentiation into osteoblastic MC3T3-E1 cells, potentially contributing to rapid osseointegration.

• The Bulletin of The Korean Astronomical Society
• /
• v.41 no.2
• /
• pp.33.1-33.1
• /
• 2016

We report detection of short-term flux variability in multi-epoch observations and intraday variability in polarized emission at millimeter-wavelength from S5 0716+714 using Korean VLBI Network (KVN) radio telescopes. Over the whole observation epochs, the source shows significant inter-month variations at K- and Q-band with modulation indices of 19% at K-band and 36% at Q-band. In each epoch, the source shows monotonic flux increase in Epoch 1 and 3, and monotonic flux decrease in Epoch 2 and 4. We found an inverted spectrum with mean spectral indices of -0.57 in Epoch 1 and -0.15 in Epoch. On the contrary, we found relatively steep indices of 0.24 and 0.17 in Epoch 2 and Epoch 4, respectively. In the study of intraday variability of polarization, we found significant variations in the degree of linear polarization at 86 GHz, and in polarization angle at 43 and 86 GHz during ~10 h. The spectrum of the source is quite flat with spectral indices of -0.07 to 0.07 at 22-43 GHz and -0.23 to 0.04 at 43-86 GHz. The measured degree of the linear polarization ranges from 2.3% to 3.3 % at 22 GHz, from 0.9% to 2.2 % at 43 GHz and from 0.4 % to 4.0 % at 86 GHz, yielding prominent variations at 86 GHz over 4-5 h. The linear polarization angle is in the range of 4 to $12^{\circ}$ at 22 GHz, -39 to $81^{\circ}$ at 43 GHz, and 66 to 119 at 86 GHz with a maximum rotation of $110^{\circ}$ at 43 GHz over ~4 h. We estimated the Faraday rotation measures (RM) ranging from -9200 to 6300 rad m-2 between 22 and 43 GHz, and from -71000 to 7300 rad m-2 between 43 and 86 GHz, respectively. The frequency dependency of RM was investigated, yielding a mean power-law index, a, of 2.0. This implies that the polarized emission from S5 0716+714 at 22-86 GHz moves through a Faraday screen in or near the jet of the source.

• Journal of Korean Home Economics Education Association
• /
• v.9 no.1
• /
• pp.1-17
• /
• 1997

This study was conducted to obtain basic materials to improve the teaching method of Home Economics by theoretically looking into the supplementary teaching materials or implements usable in teaching Costume History area. And based on these data, the types and the applications of the supplementary teaching materials or implements highschool owned were examined. The subjects of this study were 111 Home Economics and Housework curriculum highschool teachers who give a lecture in the country by using self-administered questionnaires. SAS program was used to calculate frequency, percentage, average, standard deviation, and $\chi$(sup)2-test analysis. The results of the study were as follows； 1. Most of the highschool teachers used the school expenses for experiments in preparing the supplementary teaching materials or implements. 2. Of the supplementary teaching materials and implements concerning Costume History, visual implements such as slides and pictures were the mostly owned. CD and audio implements as cassette-tapes were not used. 3. Most of the teachers recognized the importance of the audio-visual teaching materials and implements concerning Costume History. 4. Among the audio-visual materials and implements concerning Costume History by which can be made by school teachers of Home Economics and Housework curriculum, the mostly used one was ‘cutting pictorials from magazines and newspapers’, and the next were ‘orbital materials’, and ‘copy the pictorials’, and the least was ‘recording from the radio’. 5. Most of the annual expenses assigned to the department of Home Economics was used in cooking practice, and the least of the expenses was assigned in buying audio-visual teaching materials and implements. 6. Time assigned to the area of Home Economics was for the most part one or two hours per week, and among this, time assigned to the history of western costume and the history ok korean costume was for the most part five to eight hours. 7. The areas that the highschool teachers felt difficulties mostly during clothing and textiles curriculum were ‘textiles’and the next were ‘knitting’, ‘western costume history’, and ‘korean clothing construction’. 8. The difficulties the highschool teachers faced while teaching Costume History were mostly that ‘the pictorials in the text is not fully explainable’, the next were ‘most of the supplementary teaching materials or implements are not owned’, ‘have to explain very much in a short time’, and ‘the lectural explanation is insufficient’. 9. The solution for the difficulties that the highschool teachers faced while teaching Costume History was mostly ‘the information, on which audio-visual materials and implements are distributed in the market, should be easy to obtain’, the next opinions were ‘the school should provide enough experiment and practice expenses to buy audio-visual materials and implements’, and ‘education facilities of the Home Economics Department should be the main aspects in improving the teaching methods and should give special lectures about it’.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.11-11
• /
• 2008

ZnO has a very large exciton binding energy (60 meV) as well as thermal and chemical stability, which are expected to allow efficient excitonic emission, even at room temperature. ZnO based electronic devices have attracted increasing interest as the backplanes for applications in the next-generation displays, such as active-matrix liquid crystal displays (AMLCDs) and active-matrix organic light emitting diodes (AMOLEDs), and in solid state lighting systems as a substitution for GaN based light emitting diodes (LEDs). Most of these electronic devices employ the electrical behavior of n-type semiconducting active oxides due to the difficulty in obtaining a p-type film with long-term stability and high performance. p-type ZnO films can be produced by substituting group V elements (N, P, and As) for the O sites or group I elements (Li, Na, and K) for Zn sites. However, the achievement of p-type ZnO is a difficult task due to self-compensation induced from intrinsic donor defects, such as O vacancies (Vo) and Zn interstitials ($Zn_i$), or an unintentional extrinsic donor such as H. Phosphorus (P) doped ZnO thin films were grown on c-sapphire substrates by radio frequency magnetron sputtering with various Ar/ $O_2$ gas ratios. Control of the electrical types in the P-doped ZnO films was achieved by varying the gas ratio with out post-annealing. The P-doped ZnO films grown at a Ar/ $O_2$ ratio of 3/1 showed p-type conductivity with a hole concentration and hole mobility of $10^{-17}cm^{-3}$ and $2.5cm^2/V{\cdot}s$, respectively. X-ray diffraction showed that the ZnO (0002) peak shifted to lower angle due to the positioning of $p^{3-}$ ions with a smaller ionic radius in the $O^{2-}$ sites. This indicates that a p-type mechanism was due to the substitutional Po. The low-temperature photoluminescence of the p-type ZnO films showed p-type related neutral acceptor-bound exciton emission. The p-ZnO/n-Si heterojunction LEO showed typical rectification behavior, which confirmed the p-type characteristics of the ZnO films in the as-deposited status, despite the deep-level related electroluminescence emission.

• Journal of the Microelectronics and Packaging Society
• /
• v.16 no.4
• /
• pp.9-15
• /
• 2009

Compared to the flip-chip process using solder bumps, Cu pillar bump technology can accomplish much finer pitch without compromising stand-off height. Flip-chip process with Cu pillar bumps can also be utilized in radio-frequency packages where large gap between a chip and a substrate as well as fine pitch interconnection is required. In this study, Cu pillars with and without Sn caps were electrodeposited and flip-chip-bonded together to form the Cu-Sn-Cu sandwiched joints. Contact resistances and die shear forces of the Cu-Sn-Cu sandwiched joints were evaluated with variation of the height of the Sn cap electrodeposited on the Cu pillar bump. The Cu-Sn-Cu sandwiched joints, formed with Cu pillar bumps of $25-{\mu}m$ diameter and $20-{\mu}m$ height, exhibited the gap distance of $44{\mu}m$ between the chip and the substrate and the average contact resistance of $14\;m{\Omega}$/bump without depending on the Sn cap height between 10 to $25\;{\mu}m$.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.2 no.1 s.2
• /
• pp.1-13
• /
• 2003

This International Standard establishes an AVI/AEI System based on radio frequency technologies. This system is intended for general application in ITS. Specially, It allows the transfer of the identification codes and further information about equipment and vehicles used in intermodal transport into such CVO and information systems related to Intermodal Transport processes. The aim of this standard is to define, describe and specify Architecture, System Parameters, Numbering/ Data structures and interface related to an AVI/AEI system to provide an enabling Standard, which, whilst allowing the system specifier to determine the performance levels and operating conditions, provides a framework for nominal interoperability. The Standard is to establish a common framework to achieve unambiguous identification in AVI/AEI applications. Thes is AVI/AEI is designed to be an 'enabling' structure to allow interoperability between different commercial systems, and not prescriptive in determining any one system. The ISO TC204 WG4 has eight active work items. A new WI on ERI is progressing quickly; three WIs for the road environment and four multimodal WIs are under development. All Work Items are joint between CEN TC278 and ISO TC204 according to the Vienna Agreement, with CEN in the lead. The work is progressing with some delay. For all the work items, the countries who have appointed experts we: Australia, Austria, Belgium, Canada, Czech, Denmark France, Germany, Japan, Korea, the Netherlands, Norway, Spain, Sweden, UK and USA. There are 30 registered experts. The study focus on the AVI/AEcl standardization and developing of the Korea standard

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.9 s.351
• /
• pp.32-39
• /
• 2006

5.8GHz DSRC(Dedicated Short Range Communications) is a short to medium range communications service that supports both public safety and private operations in roadside to vehicle and vehicle communication. However the 5.8GHz frequency may cause the shadowing effect or communication blocking problem when there is an obstacle or another vehicle between RSE (Road Side Equipment) and OBE (On Board Equipment). In this paper, to solve this problem of the 5.8GHz DSRC, we propose a relay protocol based on the standard of DSRC radio communication between RSE and OBE in the 5.8GHz band made by TTA (Telecommunication Technology Association). By using the proposed relay protocol to DSRC system and intervehicle communication, we also consider a fixed relay protocol and mobile relay protocol. We expect to apply this relay protocol for the DSRC intervehicle communication and video communication between drivers and safe distance among vehicles in the near future.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.5
• /
• pp.445-453
• /
• 2016

This paper presents the implementation and design of the 1T-1R wireless HD video streaming systems over 28 GHz mmWave frequency using 3GPP LTE-TDD standard on NI USRP RIO SDR platform. The baseband of the system uses USRP RIO that are stored in Xilinx Kintex-7 chip to implement LTE-TDD transceiver modem, the signal that are transceived from USRP RIO up or down converts to 28 GHz by using self-designed 28 GHz RF transceiver modules and it is finally communicated HD video data through self-designed $4{\times}8$ sub array antennas. It is that communication method between USRP RIO and Host PC use PCI express ${\times}4$ to minimize delay of data to transmit and receive. The implemented system show high error vector magnitude performance above 25.85 dBc and to transceive HD video in experiment environment anywhere.

• Journal of Digital Contents Society
• /
• v.9 no.4
• /
• pp.661-667
• /
• 2008

The dynamics of business cycles has been changed by the macroscopic economic forces because of the introduction of new technical know-how each year. These the dynamics of business has a significant influence on the investment of enterprise in the information communication field. Today, the most important goal of the IT investment is simply not to lower the production cost any more, but to improve the usefulness for the customers and partners in order to obtain the optimized mass products. Therefore, the enterprises have been concentrating their all abilities on the automation, integration, and optimization of business process using BPM. In addition, they are concentrating their efforts on the business expansion by approaching the technical aspect using RFID application system. However, in order to accomplish a successful enterprise ability, the technical view, business process view, and organization view must be considered together. We suggested the method considering organization view, via the technical element, i.e., RFID system for approaching the business process. Furthermore, we tried the optimization of assignment using Context Analysis methodology and proposed the method to reduce the element with respect to the time, human, and expense by applying the Case Study method that minimizes the iteration times through the transmitted processing procedure and type. The proposed method gave us the expectation that it will bring out the innovative improvement with respect to the time, expense, quality, and customer's satisfaction in the process from the analysis of business process to the analysis and design of system.