• Nuclear Engineering and Technology
• /
• 제54권6호
• /
• pp.2253-2261
• /
• 2022

In this study, nano-scaled shielding materials were assembled and fabricated by doping different weight percentages of Nano-mercuric oxide (N-HgO) into Nano-Bentonite (N-Bent) based on using (100-x% N-Bent + x% N-HgO, x = 10, 20, 30, and 40 wt %). The fabricated N-HgO/N-Bent nanocomposites were characterized by FT-IR, XRD, and SEM and evaluated to evaluate their shielding properties toward gamma radiation by using four different γ-ray energies form three point sources; 356 keV from ¹³³Ba, 662 keV from ¹³⁷Cs as well as 1173, and 1332 keV from ⁶⁰Co. The γ-rays mass attenuation coefficients were plotted as a function of the doped N-HgO concentrations into N-HgO/N-Bent nanocomposites. The computed values of mass attenuation coefficients (µ_m), effective atomic number (Z_eff) and electron density (N_el) by the as-prepared samples were found to increase, while the half value layer (HVL) and mean free path (MFP) were identified to decrease upon increasing the N-HgO contents. It was concluded also that the increase in N-HgO concentration led to a direct increase in the mass attenuation coefficient from 0.10 to 0.17 cm²/g at 356 keV and from 0.08 to 0.09 cm²/g at 662 keV. However, a slight increase was observed in the identified mass attenuation coefficients at (1172 and 1332 keV).

• Nuclear Engineering and Technology
• /
• 제54권2호
• /
• pp.674-680
• /
• 2022

In the present study, radiation shielding and protection ability of prepared Flyash-lime-Gypsum (FaLG) bricks has been studied in terms of energy exposure build up factors and dose parameters. The energy exposure build up factors of Flyash-lime-Gypsum (FaLG) bricks have been calculated for the energy range of 0.015 MeV-15 MeV and for penetration depth upto 40 mfp directly using a new and simplified Piecewise Linear Spline Interpolation Method (PLSIM). In this new method, the calculations of G.P fitting parameters are not required. The verification and accuracy of this new method has been checked by comparing the results of exposure build up factor for NBS concrete calculated using present method with the results obtained by using G.P fitting method. Further, the relative dose distribution and reduced exposure dose rate for various radioactive isotopes without any shielding material and with Flyash-lime-Gypsum (FaLG) bricks have been calculated in the energy range of 59.59-1332 keV. On the basis of the obtained results, it has been reported that the prepared Flyash-lime-Gypsum (FaLG) bricks possess satisfactory radiation shielding properties and can be used as environmentally safe storage facilities for low level nuclear waste.

• 한국재료학회지
• /
• 제8권5호
• /
• pp.457-463
• /
• 1998

방사선물질의 수송 및 저장용기 등에 사용되는 에폭시수지계 중섣자 차폐재, KNS-201, KNS-301 및 KNS-601을 제조하였다. 기본물질은 개질 및 수소 첨가된 비스페놀 A형 그리고 노블락형 에폭시수지이며, 첨가제로는 수산화알루미늄 및 탄화붕소이다. 이들 중성자 차폐재들의 열적 및 역학적 성질 및 재방사선성 등을 평가하기 위해 여러 특성시험을 행하였다. 조사된 제반 특성들은 열분해온도;$257~280^{\circ}C$, 열전도도;0.95~1.14W/m.K, 열팽창계수 ;0.77~1.26x$10^{-6}$$^{\circ}$$C^{-1}$, 연소특성;$800^{\circ}C$이하, 평균연소시간;5초 이하, 평균연소길이 ;5mm 이하, 인장강도;2.5~3.2Kg/$\textrm{mm}^2$,압축강도:13.2~15.2kg/$\textrm{mm}^2$ 굴곡강도:5.2~604Kg/$\textrm{mm}^2$ 등을 나타냈다. 전반적으로 개발된 중성자 차폐재들의 관련 특성들이 외국에서 사용되는 중성자 차폐재, NS-4-RF보다 우수한 것으로 나타났다. 또한 KNS-601의 내방사선성이 KNS-201과 KNS-301보다 우수한 것으로 나타났다. 또한 KNS-601의 내방사선이 KNS-201과 KNS-301보다 우수한 것으로 나타났다.

• Nuclear Engineering and Technology
• /
• 제55권6호
• /
• pp.2335-2347
• /
• 2023

As medical facilities are usually built at urban areas, special concrete aggregates and evaluation methods are needed to optimize the design of concrete walls by balancing density, thickness, material composition, cost, and other factors. Carbon treatment rooms require a high radiation shielding requirement, as the neutron yield from carbon therapy is much higher than the neutron yield of protons. In this case study, the maximum carbon energy is 430 MeV/u and the maximum current is 0.27 nA from a hybrid particle therapy system. Hospital or facility construction should consider this requirement to design a special heavy concrete. In this work, magnetite is adopted as the major aggregate. Density is determined mainly by the major aggregate content of magnetite, and a heavy concrete test block was constructed for structural tests. The compressive strength is 35.7 MPa. The density ranges from 3.65 g/cm³ to 4.14 g/cm³, and the iron mass content ranges from 53.78% to 60.38% from the 12 cored sample measurements. It was found that there is a linear relationship between density and iron content, and mixing impurities should be the major reason leading to the nonuniform element and density distribution. The effect of this nonuniformity on radiation shielding properties for a carbon treatment room is investigated by three groups of Monte Carlo simulations. Higher density dominates to reduce shielding thickness. However, a higher content of high-Z elements will weaken the shielding strength, especially at a lower dose rate threshold and vice versa. The weakened side effect of a high iron content on the shielding property is obvious at 2.5 µSv=h. Therefore, we should not blindly pursue high Z content in engineering. If the thickness is constrained to 2 m, then the density can be reduced to 3.3 g/cm³, which will save cost by reducing the magnetite composition with 50.44% iron content. If a higher density of 3.9 g/cm³ with 57.65% iron content is selected for construction, then the thickness of the wall can be reduced to 174.2 cm, which will save space for equipment installation.

• Structural Engineering and Mechanics
• /
• 제87권5호
• /
• pp.499-516
• /
• 2023

To defend against harmful gamma radiation, new types of materials for use in the construction of heavyweight concrete (HWC) are still needed to be developed. This research introduces new materials to be employed as a partial replacement for fine aggregate (FA) to manufacture high-performance heavyweight concrete (HPHWC). These materials include hematite, black sand, ilmenite, and magnetite, with substitution ratios of 50% and 100% of FA. In this research, the hardening and fresh characteristics of HPHWC were obtained. Concrete samples' Gamma-ray linear attenuation coefficient was evaluated utilizing a gamma source of Co-60 through the thicknesses of 2.5, 5, 7.5, 10, 12.5, and 15 cm. High temperatures were studied for HPHWC samples, which were exposed to up to 700℃ for two hours. Energy-dispersive x-rays and a scanning electron microscope carried out microstructure analyses. Magnetite as an FA attained the lowest compressive strength of 87.1 MPa, but the best radiation protection characteristics and the highest density of 3100 kg/m³ were achieved. After 28 days, the attenuation efficiency of concrete mixtures was increased by 6.5% when fine sand was replaced with black sand at a ratio of 50%. HPHWC, which contains hematite, black sand, ilmenite, and magnetite, is designed to reduce environmental and health dangers and be used in medicinal, military, and civil applications.

• 한국방사선학회논문지
• /
• 제12권2호
• /
• pp.173-178
• /
• 2018

병원에서 방사선을 차폐하는데 있어 납은 매우 유용하게 사용되고 있다. 하지만 납은 독성을 가지고 있고 대체물질에 대한 연구가 많이 이루어지고 있으며, 대표적으로 텅스텐을 대체물질로 한 연구가 많이 이루어지고 있다. 이에 본 연구에서 납과 텅스텐의 물리적 특성 및 반가층 실험을 진행한 결과 원자번호가 높은 납 원소의 반응단면적이 텅스텐에 비해 높게 나타났으나, 텅스텐의 밀도가 높아 동일한 크기일 경우 텅스텐의 전자밀도가 납에 비해 약 1.7배 높은 것으로 나타났다. MCNPX를 이용한 모의 모사에서도 에너지 따라 다소 차이가 있지만 텅스텐이 납에 비해 약 1.4배 차폐효과가 높은 것으로 나타났으며, 텅스텐이 납에 비해 우수한 차폐효율을 갖고 있는 것으로 확인 되었다. 하지만 경제적 측면을 고려할 때 텅스텐은 희소금속으로 납에 비해 가격이 약 25배 높아 납에 대한 대체물질로는 부적당한 것으로 사료되었다.

• Nuclear Engineering and Technology
• /
• 제55권3호
• /
• pp.1061-1070
• /
• 2023

Over the last few years, lead-free inorganic metal perovskites have gained impressive ground in empowering satellites in space exploration owing to their material stability and performance evolution under extreme space environments. The present work has examined the versatility of eight such perovskites as space radiation shielding materials by computing their photon, charged particles and neutron interaction parameters. Photon interaction parameters were calculated for a wide energy range using PAGEX software. The ranges of heavy charged particles (H, He, C, N, O, Ne, Mg, Si and Fe ions) in these perovskites were estimated using SRIM software in the energy range 1 keV-10 GeV, and that of electrons was computed using ESTAR NIST software in the energy range 0.01 MeV-1 GeV. Further, the macroscopic fast neutron removal cross-sections were also calculated to estimate the neutron shielding efficiencies. The examined shielding parameters of the perovskites varied depending on the radiation type and energy. Among the selected perovskites, Cs₂TiI₆ and Ba₂AgIO₆ displayed superior photon attenuation properties. A 3.5 cm thick Ba₂AgIO₆-based shield could reduce the incident radiation intensity to half its initial value, a thickness even lesser than that of Pb-glass. Besides, CsSnBr₃ and La_0.8Ca_0.2Ni_0.5Ti_0.5O₃ displayed the highest and lowest range values, respectively, for all heavy charged particles. Ba₂AgIO₆ showed electron stopping power (on par with Kovar) better than that of other examined materials. Interestingly, La_0.8Ca_0.2Ni_0.5Ti_0.5O₃ demonstrated neutron removal cross-section values greater than that of standard neutron shielding materials - aluminium and polyethylene. On the whole, the present study not only demonstrates the employment prospects of eco-friendly perovskites for shielding space radiations but also suggests future prospects for research in this direction.

• Nuclear Engineering and Technology
• /
• 제55권4호
• /
• pp.1218-1224
• /
• 2023

We investigated the radiation shielding competence for TeO₂-V₂O₅-MoO₃ glasses. The Phy-X software was used to report the radiation shielding parameters for the present glasses. With an increase in TeO₂ and MoO₃ content, the samples' linear attenuation coefficient improves. However, at low energies, this change is more apparent. At low energy, the present samples have an effective atomic number (Z_eff) that is relatively high (in order of 16.17-24.48 at 0.347 MeV). In addition, the findings demonstrated that the density of the samples is a very critical factor in determining the half value layer (HVL). The minimal HVL for each sample can be found at 0.347 MeV and corresponds to 1.776, 1.519, 1.391, 1.210 and 1.167 cm for Te1 to Te5 respectively. However, the highest HVL of these glasses is recorded at 1.33 MeV, which corresponds to 3.773, 3.365, 3.218, 2.925 and 2.908 cm respectively. The tenth value layer results indicate that the thickness of the specimens needs to be increased in order to shield the photons that have a greater energy. Also, the TVL results demonstrated that the sample with the greatest TeO₂ and MoO₃ concentration has a higher capacity to attenuate photons.

• Nuclear Engineering and Technology
• /
• 제55권5호
• /
• pp.1734-1741
• /
• 2023

This work presents the synthesis and preparation of a new glass system described by the equation of (70-x) B₂O₃-5TeO₂ -20SrCO₃-5ZnO -xBi₂O₃, x = 0, 1, 5, 10, and 15 mol. %, using the melt quenching technique at a melting temperature of 1100 ℃. The photon-shielding characteristics mainly the linear attenuation coefficient (LAC) of the prepared glass samples were evaluated using Monte Carlo (MC) simulation N-particle transport code (MCNP-5) at gamma-ray energy extended from 59 keV to 1408 keV emitted by the radioisotopes Am-241, Ba-133, Cs-137, Co-60, Na-22, and Eu-152. Furthermore, we observed that the Bi₂O₃ content of the glasses had a significantly stronger impact on the LAC at 59 and 356 keV. The study of the lead equivalent thickness shows that the performance of fabricated glass sample with 15 mol.% of Bi₂O₃ is four times less than the performance of pure lead at low gamma photon energy while it is enhanced and became two times lower the perforce of pure lead at high energy. Therefore, the fabricated glasses special sample with 15 mol.% of Bi₂O₃ has good shielding properties in low, intermediate, and high energy intervals.

• 한국섬유공학회:학술대회논문집
• /
• 한국섬유공학회 2003년도 The Korea-Japan Joint Symposium
• /
• pp.71-72
• /
• 2003

The aim of our study is to prepare nanocomposites consisting polymer/inorganic nanoparticles and investigate their physical properties as a functional material. In this study, a nanocomposite of copper sulfide (CuS) nanoparticles introduced into a poly(acrylic acid) matrix was prepared and the optical absorption property was measured. The composite exhibited strong absorption of both ultraviolet and near-infrared rays, indicating that the composite is applicable to a solar radiation shielding filter. The wavelength of the near infrared absorption was controlled from ca.1000 nm to 1700 nm by heat and acidic solution treatments.