• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.3
• /
• pp.251-256
• /
• 2019

In this paper we proposed system and algorithm to recognize hand gestures based on the millimeter wave that is in 65GHz bandwidth. The proposed system is composed of millimeter wave radar board, analog to data conversion and data capture board and notebook to perform gesture recognition algorithms. As feature vectors in proposed algorithm. we used global and local zernike moment descriptor which are robust to distort by rotation of scaling of 2D data. As Experimental result, performance of the proposed algorithm is evaluated and compared with those of algorithms using single global or local zernike descriptor as feature vectors. In analysis of confusion matrix of algorithms, the proposed algorithm shows the better performance in comparison of precision, accuracy and sensitivity, subsequently total performance index of our method is 95.6% comparing with another two mehods in 88.4% and 84%.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.2
• /
• pp.83-92
• /
• 2022

This paper analyzes the performance of the IRA(Interferometric Radar Altimeter) by terrain type for estimating reliability of TRN(Terrain Referenced Navigation). The accuracy of the altitude is one of the key parameters of TRN's accuracy. When the antenna of the IRA has wide beamwidth, its altitude accuracy is directly affected by the configuration of the earth's surface. Hence, the accuracy and reliability of TRN can also be affected and may cause ambiguity in positioning. We present analysis data for estimating the reliability of TRN by modeling several topographies and analyzing the performance of the IRA. The results of the analysis are verified by comparison with test data.

• Composites Research
• /
• v.35 no.6
• /
• pp.469-476
• /
• 2022

In this paper, the microwave absorbing characteristics after the impact of the radar-absorbing structure (RAS) consisting of periodic pattern sheet (PPS) and glass fiber-reinforced plastic (GFRP) were experimentally investigated. The fabricated RAS effectively absorbed the microwave in the X-band (8.2-12.4 GHz). In order to induce the damage to the RAS, a low-velocity impact test with various impact energy of 15, 40, and 60 J was conducted. Afterward, the impact damage was observed by using visual inspection, non-destructive test, and image processing method. Moreover, the absorbing performance of intact and damaged RAS was measured by the free-space measurement system. The experiment results revealed that the delamination damage from the impact energy of 15 J did not considerably affect the microwave absorbing performance of the RAS. However, fiber breakage and penetration damage with a relatively large damaged area were occuured when the impact energy was increased up to 40 J and 60 J, and these failures significantly degraded the microwave absorbing characteristics of the RAS.

• Journal of Advanced Navigation Technology
• /
• v.27 no.5
• /
• pp.568-573
• /
• 2023

Range resolution is the ability to distinguish different targets placed in same angular direction but at different distances from the radar. Normally, Range resolution requirement is defined as the width of transmitting pulse. The width of transmitting pulse does not mean the ability to distinguish two different targets. Range resolution performance to detect and track targets separately depends on the signal processing and tracking algorithm not only the width of transmitting pulse. This paper analyzes the processing steps in algorithms to affect the range resolution performance and verifies the results by roof-lab ground test using beacon signal. As a result, to track targets with the same angular position separately, it is desirable to have larger range difference than plot-track association test gate.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.11
• /
• pp.1016-1027
• /
• 2015

In this paper, a orbit determination process was carried out based on KARISMA(KARI Collision Risk Management System) developed by KARI(Korea Aerospace Research Institute) to verify the orbit determination performance of this system, in which radar tracking data of a space debris was used. The real radar tracking data were obtained from TIRA(Tracking & Imaging Radar) system operated by GSOC(German Space Operation Center) for the KITSAT-3 finished satellite. And orbit determination error was approximately 60m compared to that of the GSOC's orbit determination result from the same radar tracking data. However, those results were influenced due to the insufficient information on the radar tracking data, such as error correction. To verify and confirm it, the error analysis was demonstrated and first observation data arc which has huge observation error was rejected. In this result, the orbit determination error was reduced such as approximately 25m. Therefore, if there are some observation data information such as error correction data, it is expected to improve the orbit determination accuracy.

• Journal of the Korea Society for Simulation
• /
• v.27 no.4
• /
• pp.61-68
• /
• 2018

This paper deals with ground clutter model for FOD (foreign object debris) surveillance FMCW (frequency modulated continuous waveform) radar. In the FOD surveillance radar, it has received not only the signals reflected by FOD, but also the clutters of the surface of the runway and the grassland simultaneously. However, to detect the FOD, the clutter rejection algorithm is necessary because the RCS (radar cross section) of FOD is nearly same to RCS of the grassland. In addition, it is difficult to apply the MTI (moving target indicator) algorithm as the clutter rejection algorithm because both the FOD and the clutter coexist stationarily. Hence, to remove the stationary clutter, it is crucial to accurately generate clutter map considering the surface of road. In this paper, in order to generate the clutter map, the respective beat signal at every range bin is generated in the case of only the surface without FOD, and then the beat signal accumulated 100 times. And also, Weibull distribution is applied to the RCS value to take the scattering distribution of clutter into consideration. The simulation results show that FOD can be well detected by applying the generated clutter map to the FOD FMCW radar.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.11
• /
• pp.2252-2260
• /
• 2015

In this paper, we propose a vehicular cooperative navigation system using GNSS, vision sensor and radar sensor that are frequently used in mass-produced cars. The proposed cooperative vehicular navigation system is a variant of the Hybrid-Sum Product Algorithm over Wireless Network (H-SPAWN), where we use vision and radar sensors instead of radio ranging(i.e.,UWB). The performance is compared and analyzed with respect to the sensors, especially the position estimation error decreased about fifty percent when using radar compared to vision and radio ranging. In conclusion, the proposed system with these popular sensors can improve position accuracy compared to conventional cooperative navigation system(i.e.,H-SPAWN) and decrease implementation costs.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.11
• /
• pp.1204-1212
• /
• 2008

The paper proposes a new signal model which is revised from the commonly used signal model. Recently, many research institutions had a research about CW bio-radar for detecting he heartbeat and respiration. However, when the bio-radar detects the heartbeat using the previous signal model, the bio-radar has a disadvantage of weakness about he residual phase and AWGN. Also, the model is inappropriate in ergonomics because this signal model supposes hat the heart and lung are located at a same place. In this paper, the modified signal model, which is appropriate n ergonomics, is proposed. This paper analyzes and compares with the performance for detecting the heartbeat and respiration using the previous model and revised model in AWGN and multi-path environment.

• Journal of electromagnetic engineering and science
• /
• v.9 no.3
• /
• pp.130-140
• /
• 2009

The design theory and experimental results of a true random noise radar system are presented in this paper. Target range information can be extracted precisely by correlation processing between the delayed reference and the signal received from a target, and the velocity information by the Doppler processing with successive correlation data. A K-band noise radar system was designed using random FM noise signal, and the characteristics of the fabricated system were examined with laboratory and outdoor experiments. A C-band random FM noise signal was generated by applying a low-frequency white Gaussian noise source to VCO(Voltage Controlled Oscillator), and a K-band Tx noise signal with 100 MHz bandwidth was obtained by using a following frequency multiplier. Two modified wave-guide horn arrays were designed and fabricated, and used for the Tx and Rx antennas. The required amount of Tx/Rx isolation was attained by using a coupling cancellation circuit as well as keeping them apart with predetermined spacing. A double down-conversion scheme was used in the Rx and reference channels, respectively, for easy post processing such as correlation and Doppler processing. The implemented noise radar performance was examined with a moving bicycle and a very high-speed target with a velocity of 150 m/s. The results extracted by the Matlab simulation using the logging data were found to be in a reasonable agreement with the expected results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.8
• /
• pp.784-790
• /
• 2009

A forward-looking automotive radar typically utilizes the frequency modulated continuous wave(FMCW) or pulsed-Doppler waveform for the Information acquisition of the target range and velocity. In order to obtain the high resolution target information, however, a narrow pulse width and wide bandwidth are inherently required, thus resulting in high peak power and high speed digital converter processing. In this paper, a stepped-frequency pulsed-Doppler(SFPD) waveform algorithm is proposed for high resolution forward looking automotive radar application. The performance of the proposed SFPD waveform technique is analyzed and compared with the conventional FMCW and PD method. Since this technique can be used for the high resolution target imaging with arbitrary range and Doppler resolution, it is expected to be useful In automotive radar target classification for the precision collision avoidance applications in the future.