• 한국항해학회지
• /
• 제23권1호
• /
• pp.15-22
• /
• 1999

In this paper, ferrite-rubber composite has been studied in order to apply to RF-A-PF in a super wideband electromagnetic absorber in RF-A-PF type, which can be used for a general purpose anechoic chamber. $Ni_x - Mn_0.1 - Zn_{(1-x-0.1)}ㆍFe_2O_4$ ferrite powder has been fabricated, then, using this, 〔$Ni_x - Mn_0.1 - Zn_{(1-x-0.1)}ㆍFe_2O_4$〕-Rubber composite for RF-layer in the RF-A-PF type absorber has been fabricated and it's characteristics have been analyzed. As a result, it has been clearly shown that the 〔$Ni_x - Mn_0.1 - Zn_{(1-x-0.1)}ㆍFe_2O_4$〕-Rubber composite has excellent electromagnetic wave absorbing properties.

• 한국정보통신학회논문지
• /
• 제3권1호
• /
• pp.35-42
• /
• 1999

This paper describes the characteristics of the complex isotropic ferrite-rubber composite for a super wideband electromagnetic absorber in RP-A-PF type, which can be used for an anechoic chamber, wall material to prevent TV ghost, etc. The $Ni_x-A_{0.1}-ZN_{(1-x0.1)}$. $Fe{_2}O_4$ ferrite powder has been fabricated. Using this, then, [$Ni_x-A_{0.1}-ZN_{(1-x0.1)}$. $Fe{_2}O_4$]-Rubber composite for RF-layer in the RF-A-PF type absorber has been fabricated and it's characteristics has been analyzed. As a result, it has been shown that the [$Ni_x-A_{0.1}-ZN_{(1-x0.1)}$. $Fe{_2}O_4$].Rubber composite has excellent electromagnetic wave absorbing properties.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권8호
• /
• pp.401-406
• /
• 2004

In this experimentation, we investigated the characteristics of electromagnetic wave absorption of ferroxplana powder and silicone rubber composite. Ferroxplana was prepared by flux method at low temperature. The crystallization, magnetic properties and particle morphology of the obtained ferroxplana powder were investigated by using XRD, VSM and SEM. The particle size of ferroxplana powder was 2∼4$\mu\textrm{m}$ at the ratio of R=26, The coercivity and saturation magnetization of ferroxplana powder increased slightly with increase of temperature, The magnetic loss was the main factor of electromagnetic wave absorption of ferroxplana powder and silicone rubber composite, The maximum reflection loss of composite was about -l5dB below 4GHz.

• 한국자기학회지
• /
• 제5권5호
• /
• pp.556-560
• /
• 1995

The absorption properties of Cu-Zn ferrite/rubber composite microwave absorbers with PZT(Lead Zirconate Titanate) additive were evaluated. The composite specimens have prepared by molding and curing the mixture of matrix rubber and Cu-Zn ferrite powders which are synthesized by the coprecipitation method using Fe Cl/sub 3/ .center dot. 6H/sub 2/O, CuCl/sub 2/ .center dot. 2H/sub 2/O and Zn Cl/sub 2/ as a starting raw materials. PZT is used as another filler particles to adjust the material constants of Cu-Zn ferrite/rubber composite specimens. We have found that the material constants of specimens could be controlled by various PZT mixing ratio. On the Cu-Zn ferrite/rubber composite specimens with PZT 10[wt%] additive, the reflection losses were larger than 30[dB] in the frequency range from 2.72 to 4.4[GHz]' by adjusing the thickness.

• Elastomers and Composites
• /
• 제52권4호
• /
• pp.280-286
• /
• 2017

The mechanical and dynamic properties according to the content of filler, plasticizer, and crosslinking agent of rubber composites for Lipseal were measured in this study. The mechanical properties of the composite including the silane coupling agent and silica were found to be superior to those of the composite containing carbon black. It was found that the rebound resilience characteristics were influenced by the crosslink density of sulfur rather than the filler or plasticizer. In the case of recovery, it was confirmed that the elastic restoring force improved in the compression deformation condition and recovery increased as the crosslinking density increased. The rubber composite for Lipseal of this study is expected to improve the manufacturing technology of the rubber composite which can implement the optimum function for recognizing the performance such as oil resistance, durability and compression set.

• Journal of the Korean Wood Science and Technology
• /
• 제25권4호
• /
• pp.29-38
• /
• 1997

The effect and control of wood property of reconstituted composite panels for improved board properties by wood-waste materials and development of combination method for heterogeneous materials have been of interest to the wood science researchers. The purpose of this study is to consider the properties in relation to hot pressing conditions and to develope the optimum hot pressing condition with waste wood and waste tire for the manufacturing of composite boards. The study of composite boards for recycling of wood and waste tire is nothing up to the present. Physical and mechanical properties such as specific gravity, moisture content, swelling coefficient, modulus of rupture and modulus of elasticity in bending test were studied. The condition of 3-stage press time for the lowest moisture content of composite board was $4{\rightarrow}3{\rightarrow}3$ minutes. Specific gravity of composite panels was affected mainly by the amount of rubber chip. Because of the low rigidity and high elasticity in rubber chip, it is considered the composite panel was adequate material in the place of compression load, but not bending load. Therefore, it was concluded that a use of rubber-based wood composite panel is proper to the interior materials such as floor a room than exterior materials. From the test results, the most optimum hot pressing conditions were $4{\rightarrow}3{\rightarrow}3$ minutes for 3-stage press time and $45{\rightarrow}20{\rightarrow}5kg/cm^2$ for 3-stage press pressure. The rubber-based wood composite panel was very excellent in elasticity by combination of rubber chip in comparison with existing other wood-based materials. Therefore, it was considered that rubber-based wood composites can be applicable to every interior materials such as floor a room and will be expected to effective reuse and recycle of waste tires and wood-waste materials, and will be contribute to protection of environment pollution in earth.

• Elastomers and Composites
• /
• 제58권3호
• /
• pp.128-135
• /
• 2023

To improve the adhesive strength of natural rubber (NR) for a seismic isolation damper, citraconic acid-g-NR (CCA-g-NR) was synthesized via the melt grafting of citraconic acid (CCA) onto NR using an azobisisnomerobutyronitrile (AIBN) initiator. Subsequently, the influence of CCA and AIBN concentrations on the graft ratio G/R (%) and graft efficiency G/E (%) of the CCA-g-NR was investigated. The optimum CCA and AIBN concentrations required to achieve the desired G/R (3.49%) and G/E (49.8%) were found to be 7 phr and 0.13 phr, respectively. Additionally, we studied the influence of CCA-g-NR concentration on the mechanical properties (tensile strength, elongation at break, and modulus at 300%), adhesive strength, and cure characteristics of the rubber compound in the seismic isolation damper. As the concentration of CCA-g-NR increased, the elongation at break and adhesive strength of the compound increased, whereas its tensile strength and modulus at 300% decreased. Moreover, as the concentration increased, the maximum torque decreased and the scorch time was delayed to obtain an optimal vulcanization time.

• Elastomers and Composites
• /
• 제46권4호
• /
• pp.318-323
• /
• 2011

폐타이어고무분말을 재활용하기 위하여 방수시트용 고무분말 복합체를 제조하였으며, 수지 종류와 가교제의 함량이 복합체의 기계적 특성에 미치는 영향을 고찰하였다. EPDM이 부가됨에 따라 고무분말 PE 복합체의 신장율이 3배 이상 증가하는 현상을 나타내었다. 고무분말 충전 복합체에 가교제의 농도가 증가함에 따라 복합체의 강도가 증가하였으며, 특히 재생 폴리프로필렌을 사용한 경우 3배 이상 인장강도가 현저하게 높게 나타났다. 따라서 폴리프로필렌 블렌드물로 고무분말 복합체를 제조하는 경우 신재 폴리프로필렌을 사용하는 것 보다 재생 폴리프로필렌을 사용하는 것이 기계적 특성면에서 효과적인 것으로 나타났다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 영호남학술대회 논문집
• /
• pp.155-161
• /
• 2000

In this paper, we studied the relation between heat-treatment temperature of ferrite and electromagnetic wave absorbing properties of ferrite-rubber composite. The heat-treatment temperatures of ferrite are 1200 and $1300^{\circ}C$, 2 hr. As s result. it has been shown that the optimum heat-treatment temperature of ferrite for electromagnetic wave absorber are related to the chemical composition. And, we can control electromagnetic wave absorbing properties of ferrite-rubber composite by the control of heat-treatment temperature of ferrite.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.290-293
• /
• 2004

In this paper a new sandwich composite is developed by injection silicone rubber into the honeycomb core. This composite material is designed to have a improved damping performance. For verification damping tests were conducted to the specimens with different stacked USNl25 carbon/epoxy prepreg laminate facesheets, $[0/90]_{4s},\;[0/45-45/90]_{2s},\;[45/-45]_{4s}$. Frequency response, displacement response and damping ratio were checked and compared for the both groups of specimens, with and without rubber fillings. The experimental results provided a good agreement with our original material design concept.