• Journal of Mechanical Science and Technology
• /
• 제14권5호
• /
• pp.499-507
• /
• 2000

Smooth shift is one of the key issues in automatic power transmission control systems. However, the torque sensors are too expensive to be used in shift controllers on production vehicles. In order to provide a basic strategy for smooth shifting by using RPM sensors only and in order to accomplish the shift within a designated time, this paper studies detailed characteristics of the smooth shift for clutch-to-clutch shift mechanism. A desired trajectory of slip speed is proposed for smooth acceleration shift defined in this paper. Also the clutch torque needed to achieve this trajectory is derived, and it may be used as a open loop shift control law.

• 한국분무공학회지
• /
• 제9권1호
• /
• pp.15-20
• /
• 2004

The post injection effect to enhance aftertreatment devices' performance is essential to meet future stringent emission standards by controlling exhaust gas temperature and emission pollutants. The test has been made with commercial common rail diesel engine by post injection manipulation, to optimize exhaust gas temperature while guarantee low fuel penalty. The optimization was done at 1500, 2000 and 2500[rpm] for 2, 4[bar] condition which show low exhaust gas temperature. The main purpose of this test is dedicated to understand mechanism of exhaust gas temperature rise while optimizing

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제3B권2호
• /
• pp.90-96
• /
• 2003

This paper deals with the design and the characteristic analysis of a coreless axial flux permanent magnet (AFPM) motor. Because a direct-drive wheel motor is easily derived from it, the AFPM motor is very suitable for application in an electric scooter. Compared to a conventional motor of the same size and weight, the AFPM motor is proven to have more power and torque per unit weight. In this paper, an AFPM coreless motor with a double-sided rotor disk equipped with Nd-Fe-B rare earth magnets is designed and a prototype of the motor is manufactured, which will be properly applied for the low-speed, and high-torque direct drive required for the electric scooter. The manufactured prototype of the motor has a rating of 300W, 510rpm, 5.6Nm, and 85% efficiency.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.399-404
• /
• 2002

Analyzing acoustic-structural systems such as automobiles and aircraft the FRF-based substructuring method is one of the most powerful tools. In this paper, an optimization procedure far the engine mount system of passenger car has been presented using the design sensitivity analysis based on the multi-domain FRF-based substructuring formulation. The proposed method is applied to an optimization problem of the engine mount system, of which objective is to minimize the interior sound over the concerned rpm range. The design variables selected are the stiffnesses of the engine mounts and bushes. Plugging the gradient information calculated by the proposed method into nonlinear optimization software, we can obtain the optimal stiffnesses of the engine mounts and bushings through design iterations. The optimized interior noise in the passenger car shows that the proposed method is very useful in the realistic situation.

• 한국가시화정보학회지
• /
• 제5권2호
• /
• pp.26-32
• /
• 2007

Stereoscopic PTV and Stereoscopic-PIV measurements have been carried out for the studies of the wake of a ship's propeller. Stereoscopic photogrammetry based on a 3D-PTV principle was introduced using two high-definition cameras(1k x 1k, 30Hz). The arrangement of the two cameras was based on angular position. The pair-matching of the three-dimensional velocity vectors were based on Genetic Algorithm based 3D-PTV technique. The results obtained by both measurement systems have been compared at the advance ratio J=0.88(290 rpm, d=54 mm). Turbulent properties have also been compared each other at the same condition.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.11-15
• /
• 2002

This paper presents the thermal characteristic analysis of a high-speed HMC with spindle speed of 50,000rpm. The spindle is supported by two radial and axial magnetic bearings. and the built-in motor is located between the axial and rear radial magnetic bearings. The X-axis and Y-axis feeding systems are composed of linear motor and linear motion guides, and the Z-axis feeding system is composed of servo-motor, ballscrew and linear motion guide. The thermal analysis model of high-speed HMC is constructed by the finite element method, and the thermal characteristics in the design stage are estimated based on the temperature distribution and thermal deformation under the conditions related to the heat generation of built-in motor, magnetic bearings, linear motors, servo-motor, ballscrew, and so on.

• 한국분무공학회지
• /
• 제22권4호
• /
• pp.203-209
• /
• 2017

The International maritime organization(IMO), in an effort to slow down the global warming, proposes reduction in ship's speed as a way to lower the rate emissions from ships. In addition, since ship's fuel cost have been increased, the shipping volumes, fuel-saving technology are being required urgently. Therefore, in this present study, a method of reducing the fuel cost that can improve the performance of the diesel engine was tried by introducing a predetermined amount (0.1~0.3% of the mass amount of fuel used) of hydrogen fuel additive. The experimental conditions of the test engine were 1500rpm and torque BMEP-10b ar. The engine performances (power output, fuel consumption rate, p-max, exhaust temperature) were compared before and after addition of hydrogen fuel additives. This experimental study confirmed reducing at least 2% fuel consumption and 2.19% NOx emission.

• 한국유체기계학회 논문집
• /
• 제7권4호
• /
• pp.47-52
• /
• 2004

Cryogenic pump test facility (CPTF) is designed and developed in KARI. Hydraulic and cavitation performance of pump and inducer in cryogenic environment can be measured. Working fluid is liquid nitrogen and operating temperature is $-197^{\circ}C$. Run tank, catch tank of liquid nitrogen and their pressurizing tank has been built and remote tank pressure control system are installed. Maximum power of driving motor is 320 kW and its maximum speed is 32000rpm. Cryogenic fluids and lubricating systems are effectively separated that long test times are acquired. Therefore hydraulic and cavitation performance can be measured accurately and effectively. Pre-cooling test of the facility was successfully accomplished. This facility will contribute greatly to the development of turbopump for KSLV.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2006년도 하계종합학술대회
• /
• pp.917-920
• /
• 2006

It is possible to make a practical application for many services by using Home Networking. It's brings much improve the quality of our life. Remote control communication should be made by Home Network but present networks are generally using wireless Internet. But, this method don't use exist home and not install wireless internet. Because It need to many devices. Therefore, in this paper we implement gas valve remote control system using RPM(Radio Packet Modem). We can easily installing systems and operating. This system provide different solution for Home networking.

• 조명전기설비학회논문지
• /
• 제22권3호
• /
• pp.59-65
• /
• 2008

High-speed electrical motor has been studied for several applications, i.e. for direct-drive systems of centrifugal compressors and turbo blowers. This paper deals with a design consideration of electromagnetic, mechanical and thermal limits of high-speed induction motor for turbo blower. Basic design concept of high-speed motor was proposed. As the motor is to be operated at high speed, the losses are quite different from conventional low-speed machines. Especially, the increases of rotor eddy current and friction losses could lead to an overheated motor. So, we suggested a special cooling system to reduce temperature rise. And, based upon this design concept, the prototype induction motor(37[kW], 45,000[rpm]) for high-speed turbo blower was designed and 2-D electromagnetic field analysis was implemented. Finally, criteria to evaluate the characteristics of high-speed induction motor have been proposed and tested.