• The Journal of Korean Society for Radiation Therapy
• /
• v.26 no.1
• /
• pp.83-89
• /
• 2014

Purpose : In case of the intensity modulated radiation therapy (IMRT) using Tomotherapy and linear accelerator (Linac), it was to compare and to evaluate the imaging dose of MVCT and CBCT that were performed daily for the correct set up of the patient. Materials and Methods : The human body model Phantom (Anderson rando Phantom, USA) was divided into the three parts as Head, Thorax, pelvis, and after GafChromic EBT3 film cut to the size of $0.5{\times}0.5cm2$.in the center of the recording area were situated on the ant, post, left, and right surface of the phantom and 2cm in depth from the ant, post, left, right, and center surface of the phantom, the surface dose and inner dose were measured repeatedly three times, respectively, using the tomotherapy (Hi Art) and the OBI of NovalisTx. The measured film calculated the output value by RIP version6.0 and then the average value of the dose was calculated by the one-way analysis of variance. Results : Using the human body model phantom, the results of MVCT and CBCT performance were that measurements of MVCT inner dose were showed $15.43cGy{\pm}6.05$ in the head, $16.62cGy{\pm}3.08$ in the thorax, $16.81cGy{\pm}5.24$ in the pelvis, and measurements of CBCT inner dose were showed $13.28{\pm}3.68$ in the head, from $13.66{\pm}4.04$ in the thorax, $15.52{\pm}3.52$ in the pelvis. The measurements of surface dose were showed in case of MVCT performance, $11.64{\pm}4.05$ in the head, $12.16{\pm}4.38$ in the thorax, $12.05{\pm}2.71$ in the pelvis, and in case of CBCT performance, $14.59{\pm}3.51$ in the head, $15.82{\pm}2.89$ in the thorax, $17.48{\pm}2.80$ in the pelvis, respectively. Conclusion : In case of Inner dose, the MVCT using MV energy showed higher than the CBCT using kV energy at 1.16 times in the head, at 1.22 times in the thorax, at 1.08 times in the pelvis, and in case of surface dose, the CBCT was higher than MVCT, at 1.25 times in the head, at 1.30 times in the thorax, at 1.45 times in the pelvis. Imaging dose was a small amount compared to the therapeutic dose but it was thought to affect partially to normal tissue because it was done in daily schedule. However, IMRT treatment was necessarily parallel with the IGRT treatment through the image-guide to minimize errors between planned and actual treatment. Thus, to minimize imaging dose that the patients receive, when planning the treatment, it should be set up a treatment plan considering imaging dose, or it must be performed by minimizing the scan range when shooting MVCT.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.22 no.4
• /
• pp.1-20
• /
• 1986

Physical, chemical and biological surveys on Nakdong River estuary were made from October, 1985 to September, 1986. 1. For all the seasons except summer, the sea surface temperature in northwest area of the line which linked from Seo Island to Jisim Island was I-2$^{\circ}$C lower than in southeast area, but in summer the sea surface temperature in northwest area was I-2$^{\circ}$C higher than in southeast area. On the contrary, bottom temperature of coastal area was 1$^{\circ}$C higher than that of oceanic area except winter. 2. Surface salinity in summer and fall has minimum value of 1. 9%0 and maximum value of 32.9%0. This large variation was caused by the runoff of the Nakdong River. Effect of less saline Nakdong River water in northwest area of the line which linked from Seo Island to Jisim Island was greater than in southeast area. A strong current rip always formed near this line. 3. The yellowish-green colored zone was observed in the Nakdong River estuary throughout the year by influence of river discharge. The characteristics of the water quality in the zone have shown that the water color was grade 7 by the Forel water-color meter, transparency was less than 4 m, and concentration of suspended solids was more than 5 mg/1. This water body was in the state of eutrophication in terms of chlorophyll-a and inorganic nitrogen concentration during summer season. 4. During the study period, total 276 taxa were identified. Most of them were diatoms and dinoflagellates which consisted of 97.5%. The component ratio of the above two groups was 84.4% and 13.1 % respectively. Diatoms were plentiful in December and dinoflagellates in July. Dominant species were Nitzschia seriata in October, Thalassiosira rotula in December, Skeletoncma costatum in April, and Nitzschia longissima in July. 5. A total of 47 zooplankton taxa was identified from the samples collected. Copepods were numerically the most important components of zooplankton communities in the study area. The domir:ant copepod species were Paracalanus parvus, Acartia clausi and Temora turbinata. Noctiluca scintillans was the next important component. The other zooplankton with minor abundance were Cladocera. Sagitta spp., Cnidaria, Mysidacea, Lucifer spp. and Amphipoda. 6. During the study period, fishes from 47 families and 87 species were sampled in th~ study area. The four most abundant fish species were Rep~mucen//'s valencicnnei, Leiognathus n~cha!is, Amblychaeturicllthys hexanema and Sardirel/a zun:zsi. The fish species of the secondary importance in abundance were Cynoglossus joyneri, Sillago sihama, Engra~lis japonicus, Encdrias nebulos'l, Acanthogobius flavimanus, Trichiurus lepturus, LiParis tanai/ai, Cynagloss//'s interruptus, Aj)ogon line:z!us, Thrissz la 1l.'1la!ensis, and Limanda yokohamac.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.53 no.3
• /
• pp.244-250
• /
• 2008

The purpose of this study was to measure fundamental data required for the prediction of milling ratios, and to develop regression models to predict the head rice ratio of milled rice using NIR spectra of hulled rice. A total of 81 rice samples used in this study were collected from Jeongeup, Jeonbuk province in 2006. NIR spectra were measured using one mode of measurement, reflection. The reflectance spectra were measured in the wavelength region of 400-2500 nm with an NIR spectrophotometer "NIRSystems 6500" (Foss, Silverspring, USA). Calibration equations were developed by the modified partial least squares (MPLS), partial least squares (PLS), and principal components regression (PCR). Math treatments were 1-4-4-1, 1-10-10-1, 2-4-4-1, and 2-10-10-1. The software used was WinISI (Infrasoft International, State College, USA). Automatic head rice production and quality checking system used was "SY2000-AHRPQCS" (Ssangyong, Korea). The calibration was made with the first derivative and the spectrum designated was in 8 nm interval. The determination coefficients of head rice ratios were 0.8353, 0.8416 and 0.5277 for the MPLS, PLS and PCR, respectively. Those obtained with 20 nm interval were 0.8144, 0.8354 and 0.6908 for the MPLS, PLS and PCR, respectively. The calibration was made with second derivative that spectrum designated was 8 nm in interval. The determination coefficients of head rice ratios were 0.7994, 0.8017 and 0.4473 for the MPLS, PLS and PCR, respectively. Those with 20 nm interval were 0.8004, 0.8493 and 0.6609 for the MPLS, PLS and PCR, respectively. These results indicate that the accuracy of determination coefficient for MPLS and PLS is higher than that of PCR.

• The Journal of the Korea Contents Association
• /
• v.19 no.6
• /
• pp.471-480
• /
• 2019

L-spine 3~4, L-spine 4~5, and L-spine 5~Sacrum 1 intervertebral disc(IVD) angle according to gender, age, body mass index(BMI), lumbar lordosis angle(LLA) were compared and analyzed. The anteriorposterior incidence angle of L-spine 3 ~ 4, L-spine 4 ~ 5 and L-spine 5~Sacrum 1 in body mass index were 5.66, 13.23 and 29.13 degrees in the head direction and L-spine 3 4, L-spine 4 ~ 5, L-spine 5~Sacrum 1 had 6.32 degrees, 16.09 degrees and 35.36 degrees in the head direction. The distortion area ratio comparison was performed with the phantom image using the proposed incidence angle. There was a significant difference in L-spine 4~5 and L-spine 5~Sacrum 1 IVD angle relative to body mass index and LLA(p<0.05), IVD angle and LLA were positively correlated(p<0.05).As a result of evaluating the usefulness of the image by applying the incidence angles of the disc angles according to the phantom angle of deviation to the head direction as 11 degrees for L4 and 26 degrees for L5, the distortion ratio area decreased from 14.90% to 12.11% in L4, And from 15.25% to 13.72% in L5. In anteriorposterior image of the Lumbar spine applying the incidence angle according to the measured disc angle, it is possible to reduce the distortion to purpose L4, L5. And improved the quality and diagnostic information of the target site.

• Journal of Environmental Science International
• /
• v.19 no.5
• /
• pp.647-653
• /
• 2010

The objectives of this research are to evaluate and compare the oxygen transfer coefficients($K_{La}$) in both a general bubbles reactor and a micro-nano bubbles reactor for effective operation in sewage treatment plants, and to understand the effect on microbial kinetic parameters of biomass growth for optimal biological treatment in sewage treatment plants when the micro-nano bubbles reactor is applied. Oxygen transfer coefficients($K_{La}$) of tap water and effluent of primary clarifier were determined. The oxygen transfer coefficients of the tap water for the general bubbles reactor and micro-nano bubbles reactor were found to be 0.28 $hr^{-1}$ and 2.50 $hr^{-1}$, respectively. The oxygen transfer coefficients of the effluent of the primary clarifier for the general bubbles reactor and micro-nano bubbles reactor were found be to 0.15 $hr^{-1}$ and 0.91 $hr^{-1}$, respectively. In order to figure out kinetic parameters of biomass growth for the general bubbles reactor and micro-nano bubbles reactor, oxygen uptake rates(OURs) in the saturated effluent of the primary clarifier were measured with the general bubbles reactor and micro-nano bubbles reactor. The OURs of in the saturated effluent of the primary clarifier with the general bubbles reactor and micro-nano bubbles reactor were 0.0294 mg $O_2/L{\cdot}hr$ and 0.0465 mg $O_2/L{\cdot}hr$, respectively. The higher micro-nano bubbles reactor's oxygen transfer coefficient increases the OURs. In addition, the maximum readily biodegradable substrate utilization rates($K_{ms}$) for the general bubbles reactor and micro-nano bubbles reactor were 3.41 mg COD utilized/mg active VSS day and 7.07 mg COD utilized/mg active VSS day, respectively. The maximum specific biomass growth rates for heterotrophic biomass(${\mu}_{max}$) were calculated by both values of yield for heterotrophic biomass($Y_H$) and the maximum readily biodegradable substrate utilization rates($K_{ms}$). The values of ${\mu}_{max}$ for the general bubbles reactor and micro-nano bubbles reactor were 1.62 $day^{-1}$ and 3.36 $day^{-1}$, respectively. The reported results show that the micro-nano bubbles reactor increased air-liquid contact area. This method could remove dissolved organic matters and nutrients efficiently and effectively.

• Development and Reproduction
• /
• v.17 no.4
• /
• pp.345-351
• /
• 2013

This study examines the effects on fertilization rate (FR), hatching rate (HR), and normal individual rate after artificial fertilization using frozen thawed sperm according to the cryoprotectant (DMSO) concentration and the period of cryopreserved sperm of longtooth grouper, Epinephelus bruneus. Performing artificial fertilization using frozen-thawed sperm, after freezing the sperm at different DMSO concentration of 5.0%, 7.5%, 10.0% respectively, FR were (DMSO 5.0%: $99.5{\pm}0.8%$, DMSO 7.5%: $99.5{\pm}0.7%$, and DMSO 10.0%: $99.6{\pm}0.6%$). The results are not significantly different from the control fresh sperm (100%). HR also (DMSO 5.0%: $96.2{\pm}2.3%$, DMSO 7.5%: $95.3{\pm}3.6%$, 10.0%: $96.6{\pm}1.8%$) were not significantly different in each group. The normal individual rate after hatching using with control fresh sperm ($98.4%{\pm}0.5$) and DMSO concentration level of 5.0% ($97.8{\pm}0.1%$) were not significantly different. However, with 7.5% ($97.2{\pm}0.6%$) and 10.0% DMSO concentrations ($95.9{\pm}0.2%$) are lower than the normal individual rate after hatching observed in the control and 5.0% DMSO. Performing artificial fertilization using frozen-thawed sperm at different frozen period (2 days, 2 years, and 3 years), 10% DMSO FR and HR of 3 years (FR; $66.8{\pm}1.8%$, HR: $82.0{\pm}12.9%$) and 2 years (FR; $78.5{\pm}14.8%$, HR: $79.3{\pm}0.6%$) cryopreserved sperm were lower than control (FR; 100%, HR: $91.1{\pm}3.6%$) and 2 days cryopreserved sperm (FR; $99.6{\pm}0.6%$, HR: $96.6{\pm}1.8%$). These results suggest suitable DMSO concentration ranges of cryopreservation sperm for E. bruneus is 5 to 10% and with 2 to 3 years cryopreservation period, cryopreservation sperm can be useful for seed production.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.57 no.4
• /
• pp.456-462
• /
• 2012

In the new changing scenario, the goal of agriculture is shifting from traditional to sustainable and environment-friendly agriculture. Therefore, in this experiment, we analyzed economic efficiency of two methods of rice cultivation i.e. new cultural method and conventional method, at farmers' fields. In the new cultural method, cost of materials and machines (rice-transplanting and sowing machine) was found 245% higher than the conventional method. Depreciation of cost and working hours were also higher in the new cultural method by 1.9 and 1.1 time, respectively. However, cost of seeds and seedbed soil were 44.0% and 49.2% lower and total material cost was 4.4% lower than the conventional method. In the new cultural method, overall working cost of nursery raising and transplanting per 10a was 229.8% higher than the conventional method. However, in spite of high input cost, yield of rice in new cultural method was higher by 6.7% than the conventional method. Our results showed that new cultural method was better than the conventional method except the input cost. If government provide 80% subsidy for machine cost then its input cost will be reduced by 45.4% than the conventional method.

• The Korean Journal of Mycology
• /
• v.17 no.3
• /
• pp.105-113
• /
• 1989

For selective purification of proteins in Pleurotus cornucopiae, affinity chromatography was performed by p-aminoanilinylsuccinyl-AH-Sepharose 4B gel synthesized by treating p-phenylene diamine with succinyl-AH-Sepharose 4B, which was prepared by treating AH-Sepharose 4B with succinic anhydride. The capacity of p-aminoanilinyl ligand group was 6.1 micromole per milliliter of gel. Total apparent molecular weight of the affinity proteins eluted from the synthesized gel was 167 KD, which were a protein complex of 130 KD and 37 KD. The contents of the nonpolar, polar, positively and/or negatively charged amino acids in the affinity protein were 44.57%, 24.75%, 21.25%, and 9.43%, respectively. Total apparent molecular weight of the affinity proteins eluted from the AH-Sepharose 4B gel was 95.2 KD, which were a protein complex of 61 KD, 31 KD and 3.2 KD. The contents of the nonpolar, positively and/or negatively charged amino acids in the affinity protein by AH-Sepharose 4B gel were 44.05%, 29.13%, and 12.91% respectively.

• Korean Journal of Environmental Agriculture
• /
• v.29 no.1
• /
• pp.33-38
• /
• 2010

To improve the existing nitrogen recommendation method based on chemical properties of soils and to establish new recommendation rates of nitrogen fertilizer due to different types of soils, the application rates of nitrogen fertilizer were examined in different soils of 12 experimental rice paddy fields. The application rates of nitrogen fertilizer estimated by soil-testing were higher than the rates of nitrogen standard recommendation that has been used. The application rates for minimum rice productivity ranged from a low of 168 kg/10a in sandy soil to a high of 315 kg/10a in saline soil. Amounts of nitrogen absorption in rice were proportional to the application amounts of nitrogen fertilizer in soils. Nitrogen use efficiency was the highest, 36.7%, in immatured paddy field and it was inversely proportional to the application amounts of nitrogen. the rice tasty value was the highest in the soils without nitrogen application, and also it was the lowest in the saline soils with or without nitrogen application. As comparing with the nitrogen application rates obtained by the existing nitrogen recommendation method, optimal nitrogen application rates estimated by the standardization of nitrogen application efficiency rate, environmental index, and rice quality were 1.0 fold in the well adapted soil and sandy soil fields, 0.92 fold in the immatured soil field, and 0.83 fold in the saline soil field.

• Journal of the Korean Society for Precision Engineering
• /
• v.3 no.2
• /
• pp.62-75
• /
• 1986

An experimental investigation of the machining characteristics such as cutt- ing resistance, surface roughness and tool wear in turning the test pieces of SM45C steel with both coated and uncoated carbide tool tips under various cutting conditions was conducted. Also a specially designed simple vibration damping device was experimentally evaluated for its effectiveness on machined surface roughness and a vibration test was conducted to confirm its ability to reduce the amplitude. Based on these tests finding, the following conclusions are made; 1. The cutting resistance($\textrm{p}_{1}$) increases as the depth of cut(d) increases at fixed feed rate(f) over the cutting speed(v) range of 43-226 m/min and p decreses about 18% average when V is increased for fixed d and f. At V= 226m/min, $\textrm{p}_{1}$/for A, C tips are about the same level but $\textrm{p}_{1}$ for B tip is 15% less than A, C tips. 2. The specific cutting resistance(Ks) at V=226 m/min was derived for A, B, C tips respectively and the value of Ks for B rip is about 20% less than A, C tips. 3. The surface roughness(Ra) improves significantly as the cutting speed(V) is increased and this effect was greater when V>100 m/min. On the other hand, Ra deteriorates as the feed rate(f) is increased and this trend was accelerated when f>0.3 mm/rev. With regard to the difference of Ra values among A, B, C tips, at V=226m/min, d=0.4mm, and f=0.31-0.61mm/rev, Ra values for B.C tips are about 17% less than tip A. 4. The experimental tool wear equations were derived for A, B, C tips and from these equations, the tool life($\textrm{T}_{\textrm{L}}$) baced on the I.S.O. criteria was calculated to be $\textrm{T}_{\textrm{L}}$<$\textrm{T}_{\textrm{LB}}$<$\textrm{T}_{\textrm{LC}}$ for both flank wear($\textrm{V}_{\textrm{B}}$) and boundary wear($\textrm{V}_{\textrm{N}}$). Hence, the coated tips are superior to the uncoated tip and tip C is considered to be the best. 5. The cutting resistance may be slightly reduced and the surface rounghness improved when the damper is used especially when V>100 m/min. Therefore this damping device is considered to be effective and practical. The experimental surface roughness equations were also derived. Based on the vibration test, it is established that the surface roughness improvement was the result of amplitude reduction made possible by the damper.