• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.2
• /
• pp.148-156
• /
• 2003

This paper describes the RF performance issues of UE for W-CDMA system based on 3 GPP specifications. The parameters of transmitter and receiver are derived from the viewpoint of RF performance. In order for UE to achieve high performance, the transceiver performance requirements such as ACLR, EVM, Peak Code Domain Error, spectrum emission mask, frequency error stability and TX power control dynamic range for transmitter and reference sensitivity level, blocking characteristics, noise figure, ACS, AGC dynamic range for receiver are considered. On the basis of the required parameters, the UE RF transceiver is implemented and then the evaluation of RF performance is accomplished through practical test scenarios.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2002.11a
• /
• pp.205-208
• /
• 2002

This paper presents a quantitative analysis on the intermodulation product between transmitter W-CDMA leakage signal and receiver out of band blocker, and proposes design guide lines for overcoming the effect in receiver design. Our analysis shows that duplexer isolation, attenuation and LNA IIP3 are mainly responsible for the 3rd order intermodulation product. Analysis also shows that LNA IIP3 required for meeting 3GPP TS 34.121 specification is about 1 ㏈m with duplexer isolation of 50 ㏈ and duplexer attenuation of 24㏈.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.2
• /
• pp.36-44
• /
• 2016

In this paper, an Impulse Radio-Ultra Wide band RF Transceiver for WBAN applications is implemented in $0.18{\mu}m$ CMOS technology. The designed RF transceiver support 3-5GHz UWB low band and employs OOK(On-Off Keying) modulation. The receiver employs non-coherent energy detection architecture to reduce complexity and power consumption. For the rejection of the undesired interferers and improvement of the receiver sensitivity, RF active notch filter is integrated. The VCO based transmitter employs the switch mechanism. As adapt the switch mechanism, power consumption and VCO leakage can be reduced. Also, the spectrum mask is always same at each center frequency. The measured sensitivity of the receiver is -84.1 dBm at 3.5 GHz with 1.579 Mbps. The power consumption of the transmitter and receiver are 0.3nJ/bit and 41 mW respectively.

• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.3210-3212
• /
• 2000

We designed and manufactured 300MHz NMR RF Transceiver. NMR system is composed of NMR Spectrometer, Superconductive Magnet and Pulse Programmer, GUI. NMR RF Transceiver is composed of transmitter, receiver, frequency synthesizer. T/R switch, main power amp., RF coil. To phase modulation, transmitter is composed of mixer, splitter and combiner et al. To weak signal detection, receiver is composed of pre-amp., filter, mixer et al. Each module is manufactured PCB. And installed NMR system to detect chemical component of specimen. In result, we can get the information of specimen.

• ETRI Journal
• /
• v.40 no.2
• /
• pp.167-179
• /
• 2018

This paper proposes an IEEE 802.15.4m compliant TV white-space orthogonal frequency-division multiplexing (TVWS)-(OFDM) radio frequency (RF) transceiver that can be adopted in advanced metering infrastructures, universal remote controllers, smart factories, consumer electronics, and other areas. The proposed TVWS-OFDM RF transceiver consists of a receiver, a transmitter, a 25% duty-cycle local oscillator generator, and a delta-sigma fractional-N phase-locked loop. In the TV band from 470 MHz to 698 MHz, the highly linear RF transmitter protects the occupied TV signals, and the high-Q filtering RF receiver is tolerable to in-band interferers as strong as -20 dBm at a 3-MHz offset. The proposed TVWS-OFDM RF transceiver is fabricated using a $0.13-{\mu}m$ CMOS process, and consumes 47 mA in the Tx mode and 35 mA in the Rx mode. The fabricated chip shows a Tx average power of 0 dBm with an error-vector-magnitude of < 3%, and a sensitivity level of -103 dBm with a packet-error-rate of < 3%. Using the implemented TVWS-OFDM modules, a public demonstration of electricity metering was successfully carried out.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.8
• /
• pp.1813-1819
• /
• 2011

In this research, the location positioning system supposed is concerned with range recognition technology using phase and magnitude of radio wave and adding technology of image histogram by vision. By the proposed technology, we design the radio transmitter and receiver and realize the measurement system, and save the data in disk that is earned from 900Mhz RF signal, middle frequency 450Khz of analog signal. Range information is earned the data through digital signal processing of IF signal. For the estimation of range measured, we analyze the difference between real range and measurement range, and also suggest the method to improve the measurement error using average processing and amplitude properties.

• Journal of Korea Multimedia Society
• /
• v.9 no.12
• /
• pp.1669-1680
• /
• 2006

This paper explains that the RF systems for hi-directional wireless capsule endoscopes were designed and implemented. The designed RF systems for a capsule endoscope can transmit the images of intestines from the inside to the outside of a body and the behavior of the capsules can be controlled by an external controller simultaneously. The hi-directional wireless capsule endoscope consists of a CMOS image sensor, FPGA, LED, battery, DC to DC Converter, transmitter, receiver, and antennas. The transmitter and receiver which were used in the hi-directional capsule endoscope, were designed and fabricated with $10mm(diameter){\times}3.2mm(thickness)$ dimensions taking into the MPE, power consumption, system size, signal to noise ratio and modulation method. The RF systems designed and implemented for the hi-directional wireless capsule endoscopes system were verified by in-vivo experiments. As a result, the RF systems for the hi-directional wireless capsule endoscopes satisfied the design specifications.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1666-1668
• /
• 2004

By wireless transmission data, there is high possibility to get distortion and lose by noise and barrier on wireless. If the data check damaged and lost at receiver, can't make it clear and can't judge whether this data is right or not. Therefore, by wireless transmission data need the data error check algorithm in order to decrease the data's distortion and lose and to monitoring the transmission data as real time. This study consists of RF station for wireless transmission, Water Level Meter station for water level measurement and Error check algorithm for error check of transmission data. This study is also that investigation and search for error check algorithm in order to wireless digital data transmission in condition of the least data's damage and lose. Designed transmitter and receiver with one - chip micro process to protect to swell the volume of circuit. Had designed RF transmitter - receiver station simply by means of ATMEL one - chip micro process in the systems. Used 10mW of the best RF power and 448MHz-449MHz on frequency band which can get permission to use by Frequency Law made by Korean government

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.993-997
• /
• 2004

A data error inspection algorithm for wireless digital data communication was developed. Original data converted By wireless digital data error inspection algorithm. Wireless digital data is high possibility to get distortion and lose by noise and barrier on wireless. If the data check damaged and lost at receiver, can't make it clear and can't judge whether this data is right or not. Therefore, by wireless transmission data need the data error inspection algorithm in order to decrease the data distortion and lose and to monitoring the transmission data as real time. This study consists of RF station for wireless transmission, Water Level Meter station for water level measurement and Error inspection algorithm for error check of transmission data. This study is also that investigation and search for error inspection algorithm in order to wireless digital data transmission in condition of the least data's damage and lose. Designed transmitter and receiver with one - chip micro process to protect to swell the volume of circuit. Had designed RF transmitter - receiver station simply by means of ATMEL one - chip micro processing the systems. Used 10mW of the best RF power and 448MHz-449MHz on frequency band which is open to public touse free within the limited power.

• The Journal of the Korea Contents Association
• /
• v.6 no.1
• /
• pp.8-13
• /
• 2006

In this thesis, an automatic door lock system using a dual tone multiple frequency(DTMF) signal generated as pushing the key button of mobile phone is proposed and implemented. This system consists of a transmitter module and a receiver module for processing the DTMF signal of mobile phone. The DTMF signal of mobile phone connected with ear-phone jack enter into the input terminal of DTMF receiver and those are encoded by a code-converter with 4-bits binary format in the DTMF receiver. The encoded output signals are transmitted to the amplitude shift keying(ASK) modulator of transmitter module and the modulated ASK signals which are converted into radio frequency(RF) signals propagate in a free space. The RF signals passed through a free space are demodulated by the ASK demodulator of receiver module and the demodulated ASK signals are sent to a micro-controller unit(MCU). The output signals processed by the MCU are compared with the secreted identification number which is prerecorded in a microprocessor and are transferred to a power relay. If the result is the same, the automatic door lock system opens a door. In the opposite case, it maintains closing the door. The implemented automatic door lock system operates well in mobile environments.