• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.08a
• /
• pp.138-141
• /
• 2002

The channel of the superconducting Flux Flow Transistor has been fabricated with plasma etching method using ICP. The ICP conditions were 700 W of ICP power, 150 W of rf chuck power, 5 mTorr of the pressure in chamber and 1:1 of Ar : $Cl_2$, respectively. The channel etched by plasma gas showed superconducting characteristics of over 77 K and superior surface morphology. The critical current of SFFT was altered by varying the external applied current. As the external applied current increased from 0 to 12 mA, the critical current decreased from 28 to 22 mA. Then the obtained $r_m$ values were smaller than $0.1\Omega$ at a bias current of 40 mA. The current gain was about 0.5. Output resistance was below $0.2\Omega$.

• Proceedings of the KIEE Conference
• /
• 2003.10a
• /
• pp.322-325
• /
• 2003

BST thin films were etched with inductively coupled plasmas. A chemically assisted physical etch of BST was experimentally confirmed by ICP under various gas mixtures. After a 20 % addition of $BCl_3$ to the $Cl_2/Ar$ mixture, resulting in an increased the chemical effect. As a increases of RF power, substrate power, and substrate temperature, and decrease of working pressure, the ion energy flux and chlorine atoms density increased. The maximum etch rate of the BST thin films was 90.1 nm/min at the RF power, substrate power, working pressure, and substrate temperature were 700 W, 300 W, 1.6 Pa, and 20 $^{\circ}C$, respectively. It was proposed that sputter etching is dominant etching mechanism while the contribution of chemical reaction is relatively low due to low volatility of etching product.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.179-179
• /
• 2016

A radio-frequency (RF) Inductively Coupled Plasma (ICP) torch system was used for boron-nitride nano-tube (BNNT) synthesis. Because of electrodeless plasma generation, no electrode pollution and effective heating transfer during nano-material synthesis can be realized. For stable plasma generation, argon and nitrogen gases were injected with 60 kW grid power in the difference pressure from 200 Torr to 630 Torr. Varying hydrogen gas flow rate from 0 to 20 slpm, the electrical and optical plasma properties were investigated. Through the spectroscopic analysis of atomic argon line, hydrogen line and nitrogen molecular band, we investigated the plasma electron excitation temperature, gas temperature and electron density. Based on the plasma characterization, we performed the synthesis of BNNT by inserting 0.5~1 um hexagonal-boron nitride (h-BN) powder into the plasma. We analysis the structure characterization of BNNT by SEM (Scanning Electron Microscopy) and TEM (Transmission Electron Microscopy), also grasp the ingredient of BNNT by EELS (Electron Energy Loss Spectroscopy) and Raman spectroscopy. We treated bundles of BNNT with the atmospheric pressure plasma, so that we grow the surface morphology in the water attachment of BNNT. We reduce the advancing contact angle to purity bundles of BNNT.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.10
• /
• pp.785-791
• /
• 2001

High dielectric (Ba, Sr) TiO$_3$ thin films were etched in an inductively coupled plasma (ICP) as a function of Cl$_2$/Ar mixing ration. Under Cl$_2$(20)/Ar(80), the maximum etch rate of the BST films was 400 $\AA$/mim and selectivities of BST to Pt and PR were obtained 0.4 and 0.2, respectively. Etching products were redeposited on the surface of BST and resulted in varying the nature of crystallinity. Therefore, we investigated the etched surface of BST by x-ray photoelectron spectroscopy (XPS) atomic force microscopy (AFM) and x-ray diffraction (XRD). From the result of XPS analysis, we found that residues of Ba-Cl and Ti-Cl bonds remained on the surface of the etched BST for high boiling point. The morphology of the etched surfact was analyzed by AFM. A smoothsurface(roughness ~2.8nm) ws observed under Cl$_2$(20)/Ar(80), rf power of 600 W, dc bias voltage of -250 V and pressure of 10 mTorr. This changed the nature of the crystallinity of BST. From the result of XRD analysis, the crystallinities of the etched BST film under Ar only and Cl$_2$(20)/Ar(80) were maintained as similar to as-deposited BST. However, intensity of BST(100) orientation under Cl$_2$ only plasma was abruptly decreased. This indicated that CI compounds were redeposited on the etched BST surface and resulted in changed of the crystallinity of BST during the etch process.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.13 no.3
• /
• pp.34-39
• /
• 1999

Electron temperature and electron density were rreasured in a radio-frequency inductively coupled plasma (RFICP) using a Langmuir probe method. Measurerrent was conducted in an argon discharge for pressures from 10 mTorr to 40 mTorr and input rf rnwer from 100 W to 600 W. Spatial distribution electroo temperature and electron density were rreasured for discharge with satre aspect ratio (R/L=2). Electron temperature and electron density were discovered depending on both pressure and power. Electron density was increased with iocreasing input power, but saturated at 450 W. Electron density was iocreased with iocreasing pressure. Radial distribution of the electron density was peaked at the rnsition which was a little rmved from center toward quartz window. Normal distribution of the electron density was peaked in the center between quartz plate and substrate. The above results could contribute to understand the Mechanism of Radio-Frequency Inductively Discharge Plasma.Plasma.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2008.11a
• /
• pp.51-52
• /
• 2008

결정화된 아나타이즈와 루타일 구조의 $TiO_2$ 박막을 유도결합플라즈마 화학기상증착법 (ICP-CVD)을 이용하여 증착하였다. 기판 온도는 플라즈마에 의한 가열에 의하여 최대 450K까지 증가하였다. 일반적인 플라즈마 화학기상증착법 (PE-CVD)으로 결정화된 $TiO_2$ 박막을 얻기 위해서는 최소 573K까지 가열해야 하기 때문에, 현 실험에서의 $TiO_2$ 박막은 플라즈마 가열에 의한 것이 아니라 높은 플라즈마 밀도에 의하여 증착된 것이다. 증착속도는 외부가열이 없는 상태에서 $5{\sim}50nm$/min이 얻어졌다. ICP 파워 (RF power)는 결정화도, 루타일상의 증착, 증착속도 그리고 광전류 특성에 영향을 끼쳤다.

• Journal of the Korean Vacuum Society
• /
• v.9 no.3
• /
• pp.285-289
• /
• 2000

It has been well known that weak axial magnetic field on the process plasma enhances plasma density. As the magnetic field helps a specific polarized EM wave mode to penetrate into the plasma, the energy transfer to the plasma enhances and the ion density increases. We have analyzed systematic change of the dispersion relation caused by the cyclotron resonance condition. This resonance occurs at near 5 gauss to provide minimum penetration depth, as known before. RF penetration depth increases abruptly beyond the magnetic field of 5 gauss, and this phenomena lessen as the collision frequency increases.

• Journal of the Korean Vacuum Society
• /
• v.15 no.3
• /
• pp.241-245
• /
• 2006

In this study, the characteristics of large area internal linear ICP sources of 1020mm X 920mm(substrate area is 880 X 660mm) were investigated using two different types of antenna, that is, a conventional serpentine-type antenna and a newly developed multiple U-type antenna. The multiple antenna showed a higher plasma density, a higher radical density, and more plasma stability compared to the serpentine-type antenna, and it appeared from the higher inductively coupling and less standing wave effect compared to the serpentine-type antenna. Using the multiple U-type antenna, the plasma density of $2\times10^{11}/cm^3$ with the plasma uniformity of 4% could be obtained using 15mTorr Ar and 5000W of RF power.

• Applied Chemistry for Engineering
• /
• v.18 no.1
• /
• pp.24-28
• /
• 2007

The etching of zinc oxide (ZnO) thin films has been studied using a high density plasma in a $Cl_2/Ar$ gas. The etch characteristics of ZnO thin films were systematically investigated on varying $Cl_2$ concentration, coil rf power, dc-bias voltage, and gas pressure. With increasing $Cl_2$ concentration, the etch rate of ZnO thin film increased, the redeposition around the etched patterns decreased but the sidewall slope of the etched patterns slanted. As the coil rf power and dc-bias voltage increased, the etch rates of ZnO thin films increased and etch profiles of ZnO thin films were improved. With increasing gas pressure, the etch rate of ZnO thin films slightly increased but little change in etch profile was observed. Based on these results, the optimal etching conditions of ZnO thin film were selected. Finally, the etching of ZnO thin films with a high degree of anisotropy of approximately $75^{\circ}{\sim}80^{\circ}$ without the redepositions and residues was successfully achieved at the etching conditions of 20% $Cl_2$ concentration, coil rf power of 1000 W, dc-bias voltage of 400 V, and gas pressure of 5 mTorr.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.2
• /
• pp.93-98
• /
• 2001

YMnO$_3$ films are excellent gate dielectric materials of ferroelectric random access memories (FRAMs) with MFSFET (metal -ferroelectric-semiconductor field effect transistor) structure because YMnO$_3$ films can be deposited directly on Si substrate and have a relatively low permittivity. Although the patterning of YMnO$_3$ thin films is the requisite for the fabrication of FRAMs, the etch mechanism of YMnO$_3$ thin films has not been reported. In this study, YMnO$_3$thin films were etched with Cl$_2$/Ar gas chemistries in inductively coupled plasma (ICP). The maximum etch rate of YMnO$_3$ film is 285$\AA$/min under Cl$_2$/(Cl$_2$+Ar) of 1.0, RF power of 600 W, dc-bias voltage of -200V, chamber pressure of 15 mTorr and substrate temperature of $25^{\circ}C$. The selectivities of YMnO$_3$ over CeO$_2$ and $Y_2$O$_3$ are 2.85, 1.72, respectively. The selectivities of YMnO$_3$ over PR and Pt are quite low. Chemical reaction in surface of the etched YMnO$_3$ thin films was investigated with X-ray photoelectron spectroscopy (XPS) surface of the selected YMnO$_3$ thin films was investigated with X-ray photoelectron spectroscopy(XPS) and secondary ion mass spectrometry (SIMS). The etch profile was also investigated by scaning electron microscopy(SEM)