• Journal of the Microelectronics and Packaging Society
• /
• v.6 no.3
• /
• pp.1-7
• /
• 1999

A single RF transceiver evaluation board have been developed for the purpose of application to the 900MHz band transceiver contained RF-IC chip And environment test was evaluated. The RF-IC chipset includes LNA(Low Noise Amplifier), down-conversion mixer, AGC(Automatic Gain Controller), switched capacitor filter and down sampling mixer. The RF evaluation board for the testing of chipset contained various external matching circuits, filters such as RF/IF SAW(Surface Acoustic Wave) filter and duplexer and power supply circuits. With the range of 2.7~3.3V the operated chip revealed moderate power consumption of 42mA. The chip was well operated at the receiving frequency of 925~960MHz. Measurement result is similar to general RF receiving specification of the 900MHz digital mobile phone.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.2
• /
• pp.67-72
• /
• 2011

8-layer printed circuit board is designed and implemented for triple band(2.3/2.5/3.5GHz) m-WiMAX system. In order to maintain excellent RF performance, low dielectric constant material is used for implementation of the printed circuit board. Also, embedded printed circuit board which embed passive devices is manufactured to reduce total system area. As a result, total system area is cut off by 9%. Triple band m-WiMAX system is produced using embedded printed circuit board. Furthermore, internet connecting test is performed and proved successful running of the system. The developed embedded printed circuit board will provide a effective solution for system area reduction and low loss signal RF communication system.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.145-153
• /
• 2011

In the system necessary for safety such as the train control system, to make train control information be sent correctly is very important to enable organic movement between trains. In the case of the system such as RF-CBTC (Radio Frequency Communication Based Train Control) the control related information is sent through wireless transmission between on-board system of a train and wayside transmitter. The wayside transmitter collects the running information such as location, velocity from the on-board system and operates the optimizing control by sending the control information such as the target, limited velocity to the on-board system. But, when the communication disconnect or train failure, the critical hazard such as train collision or derailment may be possible because the RF-CBTC depends on the information through wireless communication. This paper discribes of performing Fall-Back system to detect train position in the case of rail break or communication failure to avoid train accident and allows train to be operated safely. It can be implemented with ATP function through track circuits using active-type transformers and axle counters, and allows train to be operated manually in emergency status.

• Journal of the Korea Furniture Society
• /
• v.17 no.1
• /
• pp.33-46
• /
• 2006

This study was carried out to investigate a radio-frequency/vacuum (RF/V) drying ability and physical properties of the green boards and the pre-kiln dried boards with 40 mm thickness, and the 70 mm-thick green board of Iroko (Milicia excelsa). The major results were summarized as follows; The drying time from initial moisture content (MC) of 110% to approximate 6% MC for a 40mm-thick green board was 192 hours, and about 200 hours for the 70 mm-thick green board, respectively and so the RF/V drying times were dramatically shortened compared to conventional kiln drying time. The case hardenings at the RF/V drying completion stage test were very negligible, thus represented almost no existence of the residual stress. The checks were very slightly formed on all of the boards during the RF/V drying test, but crook appeared quite severely. During the accelerating test, the water-resistant treated specimens had not experienced any signs of checking occurred, whereas the control boards had encountered very frequent occurrences of end checking and slight surface checking. There were no observations of warping and discoloring regardless of the treatment.

• Proceedings of the KAIS Fall Conference
• /
• 2000.10a
• /
• pp.99-103
• /
• 2000

최근 많은 분야에서 사용피고 있는 소형 전광판을 이용하여 원거리에서도 메시지 전달이 가능한 광고용 전광판을 제작하였다. FSK Modem과 RF-Module을 이용하여 실시간으로 광고의 내용을 바꾸는 것을 원칙으로 구현하였다.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.46 no.1
• /
• pp.49-54
• /
• 2009

This paper proposes a new approach to provide RF communication channel and electric power transmission to overcome the weakness of conventional tests, which may cause several problems. When an RF communication device is used to communicate between launch vehicle and launch complex in stead of using harness umbilical, it may draw the simplicity of ground test equipments, cost-saving, and the reduction of test time. In addition, if an RF power transmission device is adopted to supply on-board power of launch vehicle, it can replace expensive on-board batteries, which may be degraded easily by the repeated charging and discharging processes.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.4 no.2 s.7
• /
• pp.23-31
• /
• 2005

ITS(Intelligent Transportation System) implementing information collection services and information support services for cars of moving fast needs a communication system of special aim such as RF-DSRC(Radio Frequency Dedicated Short Range Communication). Before RSE(Road Side Equipment) and OBE(On-Board Equipment) will be able to communicate RF-DSRC, OBE first have to request Link Initialization Access using ACTC(Activation Channel) in allocated ACTS(Activation Slot) by Slotted ALOHA. Even though Link Initialization Access is a important element to decide performance of communication system, optimal mathematic modeling study of Link Initialization Access which is adapted RF-DSRC characteristics is not enoush. So, in this paper, we propose mathematical modeling about Link Initialization Access of RF-DSRC. And then we computed Link Initialization Access probability defining offer load(G) which is adapted RF-DSRC characteristics for analyzing performance of modeling.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.9
• /
• pp.4107-4111
• /
• 2011

Therapeutic rehabilitation moped wired to process the data, because it is a complicated installation and configuration in terms of space utilization for people with disabilities have many difficulties. In this study, considering the economic costs and health-related engineering technology to develop its roots and rehabilitation of electric bicycles for the RF transceiver board data processing were developed. In particular, the low power RF transceiver in the ISM frequency bands of radio stations using the number of modules, electric bicycles and one was to enable the processing of data between PC.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.1148-1154
• /
• 2011

Vending machines to release single-use RF(Radio Frequency) transport cards at Seoul Metro stations are operated under unmanned facility and have release & charge function. This Paper introduces function, configuration of vending machine to release single-use RF transport cards, the basic concepts & overview about vending machine's operating system. And suggests programming procedure to develop OS image of Windows Embedded operating system which is onboard the main board's electronic circuitry.

• Proceedings of the IEEK Conference
• /
• 2002.06e
• /
• pp.55-58
• /
• 2002

This paper describes an RF module for 2.4GHz wireless audio/video transmission. The pre-processed baseband input signals are FM-modulated using a VCO and then transmitted through an antenna after RF filtering. The designed circuits are implemented using a Teflon board of which the size is 52mm${\times}$62mm. The measured maximum output signal levels are around -3dBm and the harmonics are less than -450dBc. The manufactured module consumes 130mA from a 8V supply.