• Journal of the Microelectronics and Packaging Society
• /
• v.17 no.1
• /
• pp.19-24
• /
• 2010

The effects of $O_2$ plasma pretreatment on the properties of Ga-doped ZnO films on PET substrate were studied. GZO films were fabricated by RF magnetron sputtering process. To improve surface energy and adhesion between the PET substrate and the GZO film, $O_2$ plasma pretreatment process was used prior to GZO sputtering. As the RF power and the treatment time increased, the crystallinity increased and the contact angle decreased significantly. When the RF power was 100 W and the treatment time was 600 sec in $O_2$ plasma pretreatment process, the resistivity of GZO films on the PET substrate was $1.90{\times}10^{-3}{\Omega}-cm$.

• Electrical & Electronic Materials
• /
• v.8 no.1
• /
• pp.77-82
• /
• 1995

PTCR(Positive Temperature Coefficient of Resistivity) thermistor in thin film BaTiO$_{3}$ system was prepared by using radio frequency(13.56 MHz) and DC magnetron sputter equipment. Polycrystalline, surface structure, and R-T(Resistivity-Temperature) characteristics of the specimens were measured by X-ray diffraction(D-Max3, Rigaku, Japan), SEM(Scanning Electron Microscopy: M.JSM84 01, Japan), and insulation resistance measuring system (Keithley 719), respectively. Thin films characteristics of the thermistor showed different properties depending on the substrate even with the same sputtering condition. The thin film formed on the A1$_{2}$O$_{3}$ substrate showed a good crystalline and a low resistivity at below curie point. However, the thin films prepared on slide glass and Si wafer were amorphous. The thicknesses of the three samples prepared under the same process conditions were 700[.angs.], 637.75[.angs.], and 715[.angs.], respectively.

• Journal of the Korean Ceramic Society
• /
• v.40 no.3
• /
• pp.262-267
• /
• 2003

The heteroepitaxial ZnO thin film on sapphire (0001) substrate was prepared by an off-axis Radio Frequency(RF) magnetron sputtering. The crystallinity of ZnO thin film was affected by deposition pressure, RF power, and substrate temperature. High quality heteroepitaxial ZnO thin film was obtained when the kinetic energy of sputtered particles is well harmonized with the surface mobility. In the result of Photoluminescence(PL) of heteroepitaxial ZnO thin film, Ultraviolet(UV) emissions at 3.36 and 3.28 eV were observed at low(17 K) and Room Temperature(RT). respectively. As the ZnO thin film was annealed in O$_2$ambient, the crystallinity was improved while UV emission was drastically decreased.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.324-324
• /
• 2007

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1996.05a
• /
• pp.39-39
• /
• 1996

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.8
• /
• pp.222-227
• /
• 2020

Pb(Zr,Ti)O₃(denoted as PZT) in the perovskite phase is used as a dielectric, piezoelectric, and super appetizer material owing to its ferroelectric properties. A PZT film was formed by an RF magnetron sputtering process by preparing a target composed of Pb_1.3(Zr_0.52Ti_0.48)O₃. The PZT film was formed by dividing the material into a mono-layer PZT produced continuously with the same sputtering power and a bi-layer PZT produced with two-stage sputtering power. The bi-layer PZT consisted of a lower layer produced under low-power sputtering conditions and an upper layer produced under the same conditions as the mono-layer PZT. XRD revealed small amounts of pyrochlore phase in the mono-layer PZT, but only the perovskite phase was detected in the bi-layer PZT. SEM and AFM revealed the upper part of the bi-layer PZT to be more compact and smooth. Moreover, the bi-layered PZT showed superior symmetry polarization and a significantly reduced leakage current of less than 1×10-5 A/cm². This phenomenon observed in bi-layer PZT was attributed to the induction of growth into a pure perovskite phase by suppressing the formation of a pyrochlore phase in the upper PZT layer where the densely formed lower PZT layer was produced sequentially.

• Journal of the Korean Vacuum Society
• /
• v.18 no.5
• /
• pp.377-383
• /
• 2009

Aluminum-doped zinc oxide (AZO) thin films were deposited on sapphire substrate by using radio-frequency magnetron sputtering and were performed in the temperature range of $600-900^{\circ}C$ by rapid thermal annealing (RTA). The crystallographic structure and the surface morphology were investigated by using X-ray diffraction and scanning electron microscopy, respectively. The crystallinity of the films was improved with increasing the annealing temperature and the average size of crystalline grains was found to be 50 nm. All the thin films showed an average transmittance of 92% in the wavelength range of 400-1100 nm. As the annealing temperature was increased, the bandgap energy was decreased and the violet photoluminescence (PL) signal at 400 nm replaced the ultraviolet PL signal. The electrical properties of the thin films showed a significant dependence on the annealing temperature.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.886-887
• /
• 2011

To obtain a transparent electrode, AZO thin film was deposited on SiOC film with various flow rates by rf magnetron sputtering system. SiOC film was deposited with various DMDMOS/O2 flow rate ratio by CVD, The optical electrical properties of the SiOC film and SiOC/AZO were analyzed by the uv visible spectrometer and 4 point prove system. The reflectance of SiOC/AZO film was changed in compared with that of SiOC film. The resistance was decreased with low RF power because of increasing the concentration of carriers.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.389-389
• /
• 2011

Transparent conductive oxide (TCO) 박막은 디스플레이 및 태양전지 등 광범위한 분야에서 적용되고 있으며, 특히 indium tin oxide (ITO)는 낮은 전기적 저항과 우수한 광투과도를 가지고 있어서 이미 많은 분야에 적용되고 있다. 본 연구는 RF와 DC를 혼용한 마그네트론 스퍼터링 공정을 활용하여 ITO 박막 특성 및 이를 활용한 유기태양전지 적용에 관한 것이다. UV-O3 처리된 glass 기판위에 thermal evaporation 방식으로 밀착력을 높이기 위하여 Cr을 5 nm 두께로 증착한 후 Al을 95 nm 증착하였다. 그 위에 스퍼터링 공정으로 ITO 박막을 In2O3:SnO2 target (10wt% SnO2)을 사용하여 1.0 mTorr의 공정압력(Ar:O2=30:1), 50W의 RF power 및 0.11kW의 DC power에서 50~250 nm의 두께로 증착하였다. ITO 박막의 결정구조 및 표면 형상은 x-ray diffraction (XRD) 및 scanning electron microscope (SEM)을 사용하여 분석하였으며, 전기적 특성은 four-point probe법으로 비저항값을 측정하였다. 또한 높은 광변환효율을 가지는 태양전지 제작을 위하여, 다양한 두께의 ITO 박막을 사용하여 ITO/ZnO/P3HT:PCBM/PEDOT/Ag 구조의 유기태양전지를 제작하여 소자 특성을 최적화 하였다.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.2
• /
• pp.233-240
• /
• 2021

For the production of neodymium-doped zinc sulfide thin films in various amounts, zinc sulfide and neodymium were simultaneously deposited using an RF magnetron sputtering equipment to form a thin films, and rapid thermal annealing was performed at 400℃ for 30 minutes as a post-treatment process. The structure, shape, and optical properties of ZnS thin films having various neodymium doping contents (0.35at.%, 1.31at.%, 1.82at.% and 1.90at.%) were studied. The X-ray diffraction pattern was grown to a (111) cubic structure in all thin films. The surface and structural morphology of the thin films due to the neodymium doping content was explained through SEM and AFM images. Only elements of Zn, S, and Nd that do not contain other impurities were identified through EDAX. The transmittance and band gap of the prepared thin films were confirmed using the UV-vis spectrum.